Job Duties Custom List 47-2082.00 — Tapers
- Install metal molding at wall corners to secure wallboard.
Occupations with related tasks Save Table: XLSX CSV
- Connect columns, beams, and girders with bolts, following blueprints and instructions from supervisors.
- Bolt aligned structural steel members in position for permanent riveting, bolting, or welding into place.
- Erect metal or precast concrete components for structures, such as buildings, bridges, dams, towers, storage tanks, fences, or highway guard rails.
- Force structural steel members into final positions, using turnbuckles, crowbars, jacks, or hand tools.
- Drive drift pins through rivet holes to align rivet holes in structural steel members with corresponding holes in previously placed members.
- Assemble hoisting equipment or rigging, such as cables, pulleys, or hooks, to move heavy equipment or materials.
- Insert sealing strips, wiring, insulating material, ladders, flanges, gauges, or valves, depending on types of structures being assembled.
- Read specifications or blueprints to determine the locations, quantities, or sizes of materials required.
- Fasten structural steel members to hoist cables, using chains, cables, or rope.
- Hoist steel beams, girders, or columns into place, using cranes or signaling hoisting equipment operators to lift and position structural steel members.
- Verify vertical and horizontal alignment of structural steel members, using plumb bobs, laser equipment, transits, or levels.
- Cut, bend, or weld steel pieces, using metal shears, torches, or welding equipment.
- Pull, push, or pry structural steel members into approximate positions for bolting into place.
- Unload and position prefabricated steel units for hoisting, as needed.
- Fabricate metal parts, such as steel frames, columns, beams, or girders, according to blueprints or instructions from supervisors.
- Dismantle structures or equipment.
- Ride on girders or other structural steel members to position them, or use rope to guide them into position.
- Hold rivets while riveters use air hammers to form heads on rivets.
- Place blocks under reinforcing bars used to reinforce floors.
- Catch hot rivets in buckets and insert rivets in holes, using tongs.
- Connect columns, beams, and girders with bolts, following blueprints and instructions from supervisors.
- Bolt aligned structural steel members in position for permanent riveting, bolting, or welding into place.
- Erect metal or precast concrete components for structures, such as buildings, bridges, dams, towers, storage tanks, fences, or highway guard rails.
- Force structural steel members into final positions, using turnbuckles, crowbars, jacks, or hand tools.
- Drive drift pins through rivet holes to align rivet holes in structural steel members with corresponding holes in previously placed members.
- Assemble hoisting equipment or rigging, such as cables, pulleys, or hooks, to move heavy equipment or materials.
- Insert sealing strips, wiring, insulating material, ladders, flanges, gauges, or valves, depending on types of structures being assembled.
- Cut and screw together metal channels to make floor or ceiling frames, according to plans for the location of rooms or hallways.
- Install horizontal and vertical metal or wooden studs to frames so that wallboard can be attached to interior walls.
- Fasten metal or rockboard lath to the structural framework of walls, ceilings, or partitions of buildings, using nails, screws, staples, or wire-ties.
- Install metal lath where plaster applications will be exposed to weather or water, or for curved or irregular surfaces.
- Fit and fasten wallboard or drywall into position on wood or metal frameworks, using glue, nails, or screws.
- Assemble or install metal framing or decorative trim for windows, doorways, or vents.
- Cut fixture or border tiles to size, using keyhole saws, and insert them into surrounding frameworks.
- Hang drywall panels on metal frameworks of walls and ceilings in offices, schools, or other large buildings, using lifts or hoists to adjust panel heights, when necessary.
- Suspend angle iron grids or channel irons from ceilings, using wire.
- Install blanket insulation between studs and tack plastic moisture barriers over insulation.
- Apply or mount acoustical tile or blocks, strips, or sheets of shock-absorbing materials to ceilings or walls of buildings to reduce reflection of sound or to decorate rooms.
- Mount tile, using adhesives, or by nailing, screwing, stapling, or wire-tying lath directly to structural frameworks.
- Nail channels or wood furring strips to surfaces to provide mounting for tile.
- Apply cement to backs of tiles and press tiles into place, aligning them with layout marks or joints of previously laid tile.
- Read blueprints or other specifications to determine methods of installation, work procedures, or material or tool requirements.
- Measure and mark surfaces to lay out work, according to blueprints or drawings, using tape measures, straightedges or squares, and marking devices.
- Measure and cut openings in panels or tiles for electrical outlets, windows, vents, plumbing, or other fixtures, using keyhole saws or other cutting tools.
- Cut metal or wood framing and trim to size, using cutting tools.
- Inspect furrings, mechanical mountings, or masonry surfaces for plumbness and level, using spirit or water levels.
- Trim rough edges from wallboard to maintain even joints, using knives.
- Coordinate work with drywall finishers who cover the seams between drywall panels.
- Scribe and cut edges of tile to fit walls where wall molding is not specified.
- Hang dry lines to wall moldings to guide positioning of main runners.
- Seal joints between ceiling tiles and walls.
- Remove existing plaster, drywall, or paneling, using crowbars and hammers.
- Wash concrete surfaces before mounting tile to increase adhesive qualities of surfaces, using washing soda and zinc sulfate solution.
- Cut and screw together metal channels to make floor or ceiling frames, according to plans for the location of rooms or hallways.
- Install horizontal and vertical metal or wooden studs to frames so that wallboard can be attached to interior walls.
- Fasten metal or rockboard lath to the structural framework of walls, ceilings, or partitions of buildings, using nails, screws, staples, or wire-ties.
- Install metal lath where plaster applications will be exposed to weather or water, or for curved or irregular surfaces.
- Fit and fasten wallboard or drywall into position on wood or metal frameworks, using glue, nails, or screws.
- Assemble or install metal framing or decorative trim for windows, doorways, or vents.
- Cut fixture or border tiles to size, using keyhole saws, and insert them into surrounding frameworks.
- Hang drywall panels on metal frameworks of walls and ceilings in offices, schools, or other large buildings, using lifts or hoists to adjust panel heights, when necessary.
- Suspend angle iron grids or channel irons from ceilings, using wire.
- Install blanket insulation between studs and tack plastic moisture barriers over insulation.
- Apply or mount acoustical tile or blocks, strips, or sheets of shock-absorbing materials to ceilings or walls of buildings to reduce reflection of sound or to decorate rooms.
- Mount tile, using adhesives, or by nailing, screwing, stapling, or wire-tying lath directly to structural frameworks.
- Nail channels or wood furring strips to surfaces to provide mounting for tile.
- Apply cement to backs of tiles and press tiles into place, aligning them with layout marks or joints of previously laid tile.
- Stretch wire, wire mesh, or chain link fencing between posts, and attach fencing to frames.
- Complete top fence rails of metal fences by connecting tube sections, using metal sleeves.
- Insert metal tubing through rail supports.
- Attach rails or tension wire along bottoms of posts to form fencing frames.
- Attach fence rail supports to posts, using hammers and pliers.
- Assemble gates, and fasten gates into position, using hand tools.
- Nail top and bottom rails to fence posts, or insert them in slots on posts.
- Erect alternate panel, basket weave, and louvered fences.
- Nail pointed slats to rails to construct picket fences.
- Construct and repair barriers, retaining walls, trellises, and other types of fences, walls, and gates.
- Establish the location for a fence, and gather information needed to ensure that there are no electric cables or water lines in the area.
- Set metal or wooden posts in upright positions in postholes.
- Measure and lay out fence lines and mark posthole positions, following instructions, drawings, or specifications.
- Align posts, by lines or sighting, and verify vertical alignment of posts, using plumb bobs or spirit levels.
- Dig postholes, using spades, posthole diggers, or power-driven augers.
- Mix and pour concrete around bases of posts, or tamp soil into postholes to embed posts.
- Make rails for fences, by sawing lumber or by cutting metal tubing to required lengths.
- Discuss fencing needs with customers, and estimate and quote prices.
- Weld metal parts together, using portable gas welding equipment.
- Blast rock formations and rocky areas with dynamite to facilitate posthole digging.
- Stretch wire, wire mesh, or chain link fencing between posts, and attach fencing to frames.
- Complete top fence rails of metal fences by connecting tube sections, using metal sleeves.
- Insert metal tubing through rail supports.
- Attach rails or tension wire along bottoms of posts to form fencing frames.
- Attach fence rail supports to posts, using hammers and pliers.
- Assemble gates, and fasten gates into position, using hand tools.
- Nail top and bottom rails to fence posts, or insert them in slots on posts.
- Erect alternate panel, basket weave, and louvered fences.
- Nail pointed slats to rails to construct picket fences.
- Construct and repair barriers, retaining walls, trellises, and other types of fences, walls, and gates.
- Install pre-assembled metal or wood frameworks for windows or doors to be fitted with glass panels, using hand tools.
- Fabricate or install metal sashes or moldings for glass installation, using aluminum or steel framing.
- Set glass doors into frames and bolt metal hinges, handles, locks, or other hardware to attach doors to frames and walls.
- Cut and attach mounting strips, metal or wood moldings, rubber gaskets, or metal clips to surfaces in preparation for mirror installation.
- Assemble, erect, or dismantle scaffolds, rigging, or hoisting equipment.
- Secure mirrors in position, using mastic cement, putty, bolts, or screws.
- Fasten glass panes into wood sashes or frames with clips, points, or moldings, adding weather seals or putty around pane edges to seal joints.
- Cut, assemble, fit, or attach metal-framed glass enclosures for showers, bathtubs, display cases, skylights, solariums, or other structures.
- Read and interpret blueprints or specifications to determine size, shape, color, type, or thickness of glass, location of framing, installation procedures, or staging or scaffolding materials required.
- Determine plumb of walls or ceilings, using plumb lines and levels.
- Operate cranes or hoists with suction cups to lift large, heavy pieces of glass.
- Cut, fit, install, repair, or replace glass or glass substitutes, such as plastic or aluminum, in building interiors or exteriors or in furniture or other products.
- Drive trucks to installation sites and unload mirrors, glass equipment, or tools.
- Load and arrange glass or mirrors onto delivery trucks, using suction cups or cranes to lift glass.
- Measure mirrors and dimensions of areas to be covered to determine work procedures.
- Pack spaces between moldings and glass with glazing compounds and trim excess material with glazing knives.
- Cut and remove broken glass prior to installing replacement glass.
- Measure and mark outlines or patterns on glass to indicate cutting lines.
- Grind or polish glass, smoothing edges when necessary.
- Score glass with cutters' wheels, breaking off excess glass by hand or with notched tools.
- Prepare glass for cutting by resting it on rack edges or against cutting tables and brushing thin layer of oil along cutting lines or dipping cutting tools in oil.
- Move furniture to clear work sites and cover floors or furnishings with drop cloths.
- Confer with customers to determine project requirements or to provide cost estimates.
- Select the type or color of glass or mirror according to specifications.
- Measure, cut, fit, and press anti-glare adhesive film to glass or spray glass with tinting solution to prevent light glare.
- Assemble and cement sections of stained glass together.
- Create patterns on glass by etching, sandblasting, or painting designs.
- Install pre-assembled metal or wood frameworks for windows or doors to be fitted with glass panels, using hand tools.
- Fabricate or install metal sashes or moldings for glass installation, using aluminum or steel framing.
- Set glass doors into frames and bolt metal hinges, handles, locks, or other hardware to attach doors to frames and walls.
- Cut and attach mounting strips, metal or wood moldings, rubber gaskets, or metal clips to surfaces in preparation for mirror installation.
- Assemble, erect, or dismantle scaffolds, rigging, or hoisting equipment.
- Secure mirrors in position, using mastic cement, putty, bolts, or screws.
- Fasten glass panes into wood sashes or frames with clips, points, or moldings, adding weather seals or putty around pane edges to seal joints.
- Cut, assemble, fit, or attach metal-framed glass enclosures for showers, bathtubs, display cases, skylights, solariums, or other structures.
- Install outer doors and door frames at elevator entrances on each floor of a structure.
- Bolt or weld steel rails to the walls of shafts to guide elevators, working from scaffolding or platforms.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Disassemble defective units, and repair or replace parts such as locks, gears, cables, and electric wiring.
- Check that safety regulations and building codes are met, and complete service reports verifying conformance to standards.
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Adjust safety controls, counterweights, door mechanisms, and components such as valves, ratchets, seals, and brake linings.
- Read and interpret blueprints to determine the layout of system components, frameworks, and foundations, and to select installation equipment.
- Connect car frames to counterweights, using steel cables.
- Maintain log books that detail all repairs and checks performed.
- Connect electrical wiring to control panels and electric motors.
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Participate in additional training to keep skills up to date.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Cut prefabricated sections of framework, rails, and other components to specified dimensions.
- Install outer doors and door frames at elevator entrances on each floor of a structure.
- Bolt or weld steel rails to the walls of shafts to guide elevators, working from scaffolding or platforms.
- Install sheet metal around insulated pipes with screws to protect the insulation from weather conditions or physical damage.
- Apply, remove, and repair insulation on industrial equipment, pipes, ductwork, or other mechanical systems such as heat exchangers, tanks, and vessels, to help control noise and maintain temperatures.
- Fit insulation around obstructions, and shape insulating materials and protective coverings as required.
- Cover, seal, or finish insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement, or asphalt mastic.
- Distribute insulating materials evenly into small spaces within floors, ceilings, or walls, using blowers and hose attachments or cement mortar.
- Move controls, buttons, or levers to start blowers, and to regulate flow of materials through nozzles.
- Measure and cut insulation for covering surfaces, using tape measures, handsaws, knives, and scissors.
- Select appropriate insulation, such as fiberglass, Styrofoam, or cork, based on the heat retaining or excluding characteristics of the material.
- Determine the amounts and types of insulation needed, and methods of installation, based on factors such as location, surface shape, and equipment use.
- Read blueprints and specifications to determine job requirements.
- Prepare surfaces for insulation application by brushing or spreading on adhesives, cement, or asphalt, or by attaching metal pins to surfaces.
- Remove or seal off old asbestos insulation, following safety procedures.
- Fill blower hoppers with insulating materials.
- Install sheet metal around insulated pipes with screws to protect the insulation from weather conditions or physical damage.
- Apply, remove, and repair insulation on industrial equipment, pipes, ductwork, or other mechanical systems such as heat exchangers, tanks, and vessels, to help control noise and maintain temperatures.
- Fit insulation around obstructions, and shape insulating materials and protective coverings as required.
- Cover, seal, or finish insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement, or asphalt mastic.
- Distribute insulating materials evenly into small spaces within floors, ceilings, or walls, using blowers and hose attachments or cement mortar.
- Move controls, buttons, or levers to start blowers, and to regulate flow of materials through nozzles.
- Install various types of bolts, including truss, glue, and resin bolts, traversing entire ceiling spans.
- Force bolts into holes, using hydraulic mechanisms of self-propelled bolting machines.
- Perform ventilation tasks, such as hanging ventilation curtains and tubes.
- Rotate chucks to turn bolts and open expansion heads against rock formations.
- Tighten ends of anchored truss bolts, using turnbuckles.
- Drill bolt holes into roofs at specified distances from ribs or adjacent bolts.
- Pull down loose rock that cannot be supported.
- Position bolting machines, and insert drill bits into chucks.
- Perform safety checks on equipment before operating.
- Perform tests to determine if methane gas is present.
- Dust rocks after bolting.
- Drill test holes and test bolts for specified tension, using torque wrenches.
- Position safety jacks to support underground mine roofs until bolts can be installed.
- Remove drill bits from chucks after drilling holes, and insert bolts into chucks.
- Install various types of bolts, including truss, glue, and resin bolts, traversing entire ceiling spans.
- Force bolts into holes, using hydraulic mechanisms of self-propelled bolting machines.
- Perform ventilation tasks, such as hanging ventilation curtains and tubes.
- Rotate chucks to turn bolts and open expansion heads against rock formations.
- Tighten ends of anchored truss bolts, using turnbuckles.
- Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.
- Fabricate concrete beams, columns, and panels.
- Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.
- Check the forms that hold the concrete to see that they are properly constructed.
- Set the forms that hold concrete to the desired pitch and depth, and align them.
- Spread, level, and smooth concrete, using rake, shovel, hand or power trowel, hand or power screed, and float.
- Monitor how the wind, heat, or cold affect the curing of the concrete throughout the entire process.
- Mold expansion joints and edges, using edging tools, jointers, and straightedge.
- Signal truck driver to position truck to facilitate pouring concrete, and move chute to direct concrete on forms.
- Direct the casting of the concrete and supervise laborers who use shovels or special tools to spread it.
- Produce rough concrete surface, using broom.
- Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.
- Operate power vibrator to compact concrete.
- Waterproof or restore concrete surfaces, using appropriate compounds.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Chip, scrape, and grind high spots, ridges, and rough projections to finish concrete, using pneumatic chisels, power grinders, or hand tools.
- Cut out damaged areas, drill holes for reinforcing rods, and position reinforcing rods to repair concrete, using power saw and drill.
- Wet concrete surface, and rub with stone to smooth surface and obtain specified finish.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Build wooden molds, and clamp molds around area to be repaired, using hand tools.
- Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.
- Polish surface, using polishing or surfacing machine.
- Cut metal division strips, and press them into terrazzo base so that top edges form desired design or pattern.
- Push roller over surface to embed chips in surface.
- Apply muriatic acid to clean surface, and rinse with water.
- Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.
- Fabricate concrete beams, columns, and panels.
- Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.
- Position and secure steel bars, rods, cables, or mesh in concrete forms, using fasteners, rod-bending machines, blowtorches, or hand tools.
- Space and fasten together rods in forms according to blueprints, using wire and pliers.
- Determine quantities, sizes, shapes, and locations of reinforcing rods from blueprints, sketches, or oral instructions.
- Cut rods to required lengths, using metal shears, hacksaws, bar cutters, or acetylene torches.
- Place blocks under rebar to hold the bars off the deck when reinforcing floors.
- Cut and fit wire mesh or fabric, using hooked rods, and position fabric or mesh in concrete to reinforce concrete.
- Bend steel rods with hand tools or rod-bending machines and weld them with arc-welding equipment.
- Position and secure steel bars, rods, cables, or mesh in concrete forms, using fasteners, rod-bending machines, blowtorches, or hand tools.
- Space and fasten together rods in forms according to blueprints, using wire and pliers.
- Position, align, and secure structural parts or related assemblies to boiler frames, tanks, or vats of pressure vessels, following blueprints.
- Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.
- Attach rigging and signal crane or hoist operators to lift heavy frame and plate sections or other parts into place.
- Study blueprints to determine locations, relationships, or dimensions of parts.
- Repair or replace defective pressure vessel parts, such as safety valves or regulators, using torches, jacks, caulking hammers, power saws, threading dies, welding equipment, or metalworking machinery.
- Locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments.
- Bolt or arc weld pressure vessel structures and parts together, using wrenches or welding equipment.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Shape or fabricate parts, such as stacks, uptakes, or chutes, to adapt pressure vessels, heat exchangers, or piping to premises, using heavy-metalworking machines such as brakes, rolls, or drill presses.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Lay out plate, sheet steel, or other heavy metal and locate and mark bending and cutting lines, using protractors, compasses, and drawing instruments or templates.
- Examine boilers, pressure vessels, tanks, or vats to locate defects, such as leaks, weak spots, or defective sections, so that they can be repaired.
- Shape seams, joints, or irregular edges of pressure vessel sections or structural parts to attain specified fit of parts, using cutting torches, hammers, files, or metalworking machines.
- Inspect assembled vessels or individual components, such as tubes, fittings, valves, controls, or auxiliary mechanisms, to locate any defects.
- Straighten or reshape bent pressure vessel plates or structure parts, using hammers, jacks, or torches.
- Clean pressure vessel equipment, using scrapers, wire brushes, and cleaning solvents.
- Bell, bead with power hammers, or weld pressure vessel tube ends to ensure leakproof joints.
- Position, align, and secure structural parts or related assemblies to boiler frames, tanks, or vats of pressure vessels, following blueprints.
- Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.
