Job Duties Custom List 47-3016.00 — Helpers--Roofers
- Apply shingles, gravel, or asphalt over the top layer of tar to protect the roofing material.
Occupations with related tasks Save Table: XLSX CSV
- Cement or nail flashing strips of metal or shingle over joints to make them watertight.
- Install partially overlapping layers of material over roof insulation surfaces, using chalk lines, gauges on shingling hatchets, or lines on shingles.
- Apply plastic coatings, membranes, fiberglass, or felt over sloped roofs before applying shingles.
- Install, repair, or replace single-ply roofing systems, using waterproof sheet materials such as modified plastics, elastomeric, or other asphaltic compositions.
- Attach roofing paper to roofs in overlapping strips to form bases for other materials.
- Cover roofs or exterior walls of structures with slate, asphalt, aluminum, wood, gravel, gypsum, or related materials, using brushes, knives, punches, hammers, or other tools.
- Apply reflective roof coatings, such as special paints or single-ply roofing sheets, to existing roofs to reduce solar heat absorption.
- Apply alternate layers of hot asphalt or tar and roofing paper to roofs.
- Glaze top layers to make a smooth finish or embed gravel in the bitumen for rough surfaces.
- Apply gravel or pebbles over top layers of roofs, using rakes or stiff-bristled brooms.
- Set up scaffolding to provide safe access to roofs.
- Install vapor barriers or layers of insulation on flat roofs.
- Mop or pour hot asphalt or tar onto roof bases.
- Install attic ventilation systems, such as turbine vents, gable or ridge vents, or conventional or solar-powered exhaust fans.
- Install skylights on roofs to increase natural light inside structures or to reduce energy costs.
- Apply modular soil- and plant-containing grids over existing roof membranes to create green roofs.
- Install layers of vegetation-based green roofs, including protective membranes, drainage, aeration, water retention and filter layers, soil substrates, irrigation materials, and plants.
- Inspect problem roofs to determine the best repair procedures.
- Remove snow, water, or debris from roofs prior to applying roofing materials.
- Estimate materials and labor required to complete roofing jobs.
- Cut felt, shingles, or strips of flashing to fit angles formed by walls, vents, or intersecting roof surfaces.
- Waterproof or damp-proof walls, floors, roofs, foundations, or basements by painting or spraying surfaces with waterproof coatings or by attaching waterproofing membranes to surfaces.
- Cover exposed nailheads with roofing cement or caulking to prevent water leakage or rust.
- Smooth rough spots to prepare surfaces for waterproofing, using hammers, chisels, or rubbing bricks.
- Install solar roofing systems that have energy-collecting photovoltaic panels built into roofing membranes, shingles, or tiles.
- Spray roofs, sidings, or walls to bind, seal, insulate, or soundproof sections of structures, using spray guns, air compressors, or heaters.
- Attach solar panels to existing roofs, according to specifications and without damaging roofing materials or the structural integrity of buildings.
- Punch holes in slate, tile, terra cotta, or wooden shingles, using punches and hammers.
- Cement or nail flashing strips of metal or shingle over joints to make them watertight.
- Install partially overlapping layers of material over roof insulation surfaces, using chalk lines, gauges on shingling hatchets, or lines on shingles.
- Apply plastic coatings, membranes, fiberglass, or felt over sloped roofs before applying shingles.
- Install, repair, or replace single-ply roofing systems, using waterproof sheet materials such as modified plastics, elastomeric, or other asphaltic compositions.
- Attach roofing paper to roofs in overlapping strips to form bases for other materials.
- Cover roofs or exterior walls of structures with slate, asphalt, aluminum, wood, gravel, gypsum, or related materials, using brushes, knives, punches, hammers, or other tools.
- Apply reflective roof coatings, such as special paints or single-ply roofing sheets, to existing roofs to reduce solar heat absorption.
- Apply alternate layers of hot asphalt or tar and roofing paper to roofs.
- Glaze top layers to make a smooth finish or embed gravel in the bitumen for rough surfaces.
- Apply gravel or pebbles over top layers of roofs, using rakes or stiff-bristled brooms.
- Set up scaffolding to provide safe access to roofs.
- Install vapor barriers or layers of insulation on flat roofs.
- Mop or pour hot asphalt or tar onto roof bases.
- Install attic ventilation systems, such as turbine vents, gable or ridge vents, or conventional or solar-powered exhaust fans.
- Install skylights on roofs to increase natural light inside structures or to reduce energy costs.
- Apply modular soil- and plant-containing grids over existing roof membranes to create green roofs.
- Install layers of vegetation-based green roofs, including protective membranes, drainage, aeration, water retention and filter layers, soil substrates, irrigation materials, and plants.
- Supply and place base materials, edge restraints, bedding sand and jointing sand.
- Sweep sand into the joints and compact pavement until the joints are full.
- Prepare base for installation by removing unstable or unsuitable materials, compacting and grading the soil, draining or stabilizing weak or saturated soils and taking measures to prevent water penetration and migration of bedding sand.
- Screed sand level to an even thickness, and recheck sand exposed to elements, raking and rescreeding if necessary.
- Compact bedding sand and pavers to finish the paved area, using a plate compactor.
- Resurface an outside area with cobblestones, terracotta tiles, concrete or other materials.
- Cement the edges of the paved area.
- Discuss the design with the client.
- Set pavers, aligning and spacing them correctly.
- Cut paving stones to size and for edges, using a splitter and a masonry saw.
- Design paver installation layout pattern and create markings for directional references of joints and stringlines.
- Sweep sand from the surface prior to opening to traffic.
- Supply and place base materials, edge restraints, bedding sand and jointing sand.
- Sweep sand into the joints and compact pavement until the joints are full.
- Prepare base for installation by removing unstable or unsuitable materials, compacting and grading the soil, draining or stabilizing weak or saturated soils and taking measures to prevent water penetration and migration of bedding sand.
- Screed sand level to an even thickness, and recheck sand exposed to elements, raking and rescreeding if necessary.
- Compact bedding sand and pavers to finish the paved area, using a plate compactor.
- Resurface an outside area with cobblestones, terracotta tiles, concrete or other materials.
- Cement the edges of the paved area.
- Secure metal roof panels in place by interlocking and fastening grooved panel edges.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Maintain equipment, making repairs or modifications when necessary.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Transport prefabricated parts to construction sites for assembly and installation.
- Hire, train, or supervise new employees or apprentices.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Fabricate or alter parts at construction sites, using shears, hammers, punches, or drills.
- Determine project requirements, such as scope, assembly sequences, or required methods or materials, using blueprints, drawings, or written or verbal instructions.
- Maneuver completed roofing units into position for installation.
- Select gauges or types of sheet metal or nonmetallic material, according to product specifications.
- Shape metal material over anvils, blocks, or other forms, using hand tools.
- Trim, file, grind, deburr, buff, or smooth surfaces, seams, or joints of assembled parts, using hand tools or portable power tools.
- Inspect individual parts, assemblies, or installations, using measuring instruments, such as calipers, scales, or micrometers.
- Develop or lay out patterns, using computerized metalworking equipment.
- Convert blueprints into shop drawings to be followed in the construction or assembly of sheet metal products.
- Perform sheet metal work necessary for solar panel installations.
- Verify that heating, ventilating, and air conditioning (HVAC) systems are designed, installed, and calibrated in accordance with green certification standards, such as those of Leadership in Energy and Environmental Design (LEED).
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
- Finish parts, using hacksaws or hand, rotary, or squaring shears.
- Secure metal roof panels in place by interlocking and fastening grooved panel edges.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Clean, grade, or level ballast on railroad tracks.
- Drive graders, tamping machines, brooms, or ballast spreading machines to redistribute gravel or ballast between rails.
- Patrol assigned track sections so that damaged or broken track can be located and reported.
- Repair or adjust track switches, using wrenches and replacement parts.
- Weld sections of track together, such as switch points and frogs.
- Observe leveling indicator arms to verify levelness and alignment of tracks.
- Operate single- or multiple-head spike driving machines to drive spikes into ties and secure rails.
- Operate track wrenches to tighten or loosen bolts at joints that hold ends of rails together.
- Cut rails to specified lengths, using rail saws.
- Lubricate machines, change oil, or fill hydraulic reservoirs to specified levels.
- Drill holes through rails, tie plates, or fishplates for insertion of bolts or spikes, using power drills.
- Clean tracks or clear ice or snow from tracks or switch boxes.
- Raise rails, using hydraulic jacks, to allow for tie removal and replacement.
- Adjust controls of machines that spread, shape, raise, level, or align track, according to specifications.
- Dress and reshape worn or damaged railroad switch points or frogs, using portable power grinders.
- Clean or make minor repairs to machines or equipment.
- Grind ends of new or worn rails to attain smooth joints, using portable grinders.
- Operate single- or multiple-head spike pullers to pull old spikes from ties.
- String and attach wire-guidelines machine to rails so that tracks or rails can be aligned or leveled.
- Engage mechanisms that lay tracks or rails to specified gauges.
- Drive vehicles that automatically move and lay tracks or rails over sections of track to be constructed, repaired, or maintained.
- Turn wheels of machines, using lever controls, to adjust guidelines for track alignments or grades, following specifications.
- Push controls to close grasping devices on track or rail sections so that they can be raised or moved.
- Operate tie-adzing machines to cut ties and permit insertion of fishplates that hold rails.
- Paint railroad signs, such as speed limits or gate-crossing warnings.
- Spray ties, fishplates, or joints with oil to protect them from weathering.
- Clean, grade, or level ballast on railroad tracks.
- Drive graders, tamping machines, brooms, or ballast spreading machines to redistribute gravel or ballast between rails.
- Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.
- Spread, level, and smooth concrete, using rake, shovel, hand or power trowel, hand or power screed, and float.
- Mold expansion joints and edges, using edging tools, jointers, and straightedge.
- Signal truck driver to position truck to facilitate pouring concrete, and move chute to direct concrete on forms.
- Produce rough concrete surface, using broom.
- Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.
- Operate power vibrator to compact concrete.
- Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.
- Wet concrete surface, and rub with stone to smooth surface and obtain specified finish.
- Fabricate concrete beams, columns, and panels.
- Check the forms that hold the concrete to see that they are properly constructed.
- Set the forms that hold concrete to the desired pitch and depth, and align them.
- Monitor how the wind, heat, or cold affect the curing of the concrete throughout the entire process.
- Direct the casting of the concrete and supervise laborers who use shovels or special tools to spread it.
- Waterproof or restore concrete surfaces, using appropriate compounds.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Chip, scrape, and grind high spots, ridges, and rough projections to finish concrete, using pneumatic chisels, power grinders, or hand tools.
- Cut out damaged areas, drill holes for reinforcing rods, and position reinforcing rods to repair concrete, using power saw and drill.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Build wooden molds, and clamp molds around area to be repaired, using hand tools.
- Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.
- Polish surface, using polishing or surfacing machine.
- Cut metal division strips, and press them into terrazzo base so that top edges form desired design or pattern.
- Push roller over surface to embed chips in surface.
- Apply muriatic acid to clean surface, and rinse with water.
- Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.
- Spread, level, and smooth concrete, using rake, shovel, hand or power trowel, hand or power screed, and float.
- Mold expansion joints and edges, using edging tools, jointers, and straightedge.
- Signal truck driver to position truck to facilitate pouring concrete, and move chute to direct concrete on forms.
- Produce rough concrete surface, using broom.
- Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.
- Operate power vibrator to compact concrete.
- Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.
- Wet concrete surface, and rub with stone to smooth surface and obtain specified finish.
- Fabricate concrete beams, columns, and panels.
- Spread roofing paper on surface of foundation and spread concrete onto roofing paper with trowel to form terrazzo base.
- Spread, level, or smooth concrete or terrazzo mixtures to form bases or finished surfaces, using rakes, shovels, hand or power trowels, hand or power screeds, or floats.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth with a trowel.
- Mold expansion joints and edges, using edging tools, jointers, or straightedges.
- Precast terrazzo blocks in wooden forms.
- Wet concrete surface and rub with stone to smooth surface and obtain specified finish.
- Produce rough concrete surface, using broom.
- Signal truck driver to position truck to facilitate pouring concrete and move chute to direct concrete on forms.
- Measure designated amounts of ingredients for terrazzo or grout, according to standard formulas and specifications, using graduated containers and scales, and load ingredients into portable mixer.
- Grind surfaces with a power grinder, or polish surfaces with polishing or surfacing machines.
- Cut metal division strips and press them into the terrazzo base for joints or changes of color to form designs or patterns or to help prevent cracks.
- Blend marble chip mixtures, place into panels, and push a roller over the surface to embed the chips.
- Modify mixing, grouting, grinding, or cleaning procedures, according to type of installation or material used.
- Grind curved surfaces or areas inaccessible to surfacing machine, such as stairways or cabinet tops, with portable hand grinder.
- Wash polished terrazzo surface, using cleaner and water, and apply sealer and curing agent according to manufacturer's specifications, using brush or sprayer.
- Position and secure moisture membrane and wire mesh in preparation for pouring base materials for terrazzo installation.
- Fill slight grinding depressions with matching grout material and hand-trowel for a smooth, uniform surface.
- Clean installation site, mixing and storage areas, tools, machines, and equipment, and store materials and equipment.
- Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Chip, scrape, or grind high spots, ridges, or rough projections to finish concrete, using pneumatic chisel, hand chisel, or other hand tools.
- Move terrazzo installation materials, tools, machines, or work devices to work areas, manually or using wheelbarrow.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Repair concrete by cutting out damaged areas, drilling holes for reinforcing rods, and positioning reinforcing rods, using power saw and drill.
- Build wooden molds, clamping molds around areas to be repaired, or setting up frames to the proper depth and alignment.
- Remove frames when the foundation is dry.
- Spread roofing paper on surface of foundation and spread concrete onto roofing paper with trowel to form terrazzo base.
- Spread, level, or smooth concrete or terrazzo mixtures to form bases or finished surfaces, using rakes, shovels, hand or power trowels, hand or power screeds, or floats.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth with a trowel.
- Mold expansion joints and edges, using edging tools, jointers, or straightedges.
- Precast terrazzo blocks in wooden forms.
- Wet concrete surface and rub with stone to smooth surface and obtain specified finish.
- Produce rough concrete surface, using broom.
- Signal truck driver to position truck to facilitate pouring concrete and move chute to direct concrete on forms.
- Cover pipes with earth or other materials.
- Connect pipe pieces and seal joints, using welding equipment, cement, or glue.
- Grade or level trench bases, using tamping machines or hand tools.
- Dig trenches to desired or required depths, by hand or using trenching tools.
- Install or use instruments such as lasers, grade rods, or transit levels.
- Cut pipes to required lengths.
- Install or repair sanitary or stormwater sewer structures or pipe systems.
- Align and position pipes to prepare them for welding or sealing.
- Check slopes for conformance to requirements, using levels or lasers.
- Lay out pipe routes, following written instructions or blueprints and coordinating layouts with supervisors.
- Operate mechanized equipment, such as pickup trucks, rollers, tandem dump trucks, front-end loaders, or backhoes.
- Tap and drill holes into pipes to introduce auxiliary lines or devices.
- Locate existing pipes needing repair or replacement, using magnetic or radio indicators.
- Train or supervise others in laying pipe.
- Cover pipes with earth or other materials.
- Connect pipe pieces and seal joints, using welding equipment, cement, or glue.
- Grade or level trench bases, using tamping machines or hand tools.
- Dig trenches to desired or required depths, by hand or using trenching tools.
- Haul and spread sand, gravel, and clay to fill washouts and repair road shoulders.
- Erect, install, or repair guardrails, road shoulders, berms, highway markers, warning signals, and highway lighting, using hand tools and power tools.
- Dump, spread, and tamp asphalt, using pneumatic tampers, to repair joints and patch broken pavement.
- Place and remove snow fences used to prevent the accumulation of drifting snow on highways.
- Set out signs and cones around work areas to divert traffic.
- Flag motorists to warn them of obstacles or repair work ahead.
- Perform preventative maintenance on vehicles and heavy equipment.
- Drive trucks to transport crews and equipment to work sites.
- Clean and clear debris from culverts, catch basins, drop inlets, ditches, and other drain structures.
- Drive heavy equipment and vehicles with adjustable attachments to sweep debris from paved surfaces, mow grass and weeds, remove snow and ice, and spread salt and sand.
- Inspect, clean, and repair drainage systems, bridges, tunnels, and other structures.
- Remove litter and debris from roadways, including debris from rock and mud slides.
- Perform roadside landscaping work, such as clearing weeds and brush, and planting and trimming trees.
- Apply poisons along roadsides and in animal burrows to eliminate unwanted roadside vegetation and rodents.
- Measure and mark locations for installation of markers, using tape, string, or chalk.
- Paint traffic control lines and place pavement traffic messages, by hand or using machines.
- Apply oil to road surfaces, using sprayers.
- Inspect markers to verify accurate installation.
- Blend compounds to form adhesive mixtures used for marker installation.
- Haul and spread sand, gravel, and clay to fill washouts and repair road shoulders.
- Erect, install, or repair guardrails, road shoulders, berms, highway markers, warning signals, and highway lighting, using hand tools and power tools.
- Dump, spread, and tamp asphalt, using pneumatic tampers, to repair joints and patch broken pavement.
- Place and remove snow fences used to prevent the accumulation of drifting snow on highways.
- Set up and tear down equipment.
- Operate machines to spread, smooth, level, or steel-reinforce stone, concrete, or asphalt on road beds.
- Operate tamping machines or manually roll surfaces to compact earth fills, foundation forms, and finished road materials, according to grade specifications.
- Start machine, engage clutch, and push and move levers to guide machine along forms or guidelines and to control the operation of machine attachments.
- Fill tanks, hoppers, or machines with paving materials.
- Control paving machines to push dump trucks and to maintain a constant flow of asphalt or other material into hoppers or screeds.
- Observe distribution of paving material to adjust machine settings or material flow, and indicate low spots for workers to add material.
- Coordinate truck dumping.
- Drive machines onto truck trailers, and drive trucks to transport machines and material to and from job sites.
- Inspect, clean, maintain, and repair equipment, using mechanics' hand tools, or report malfunctions to supervisors.
- Light burners or start heating units of machines, and regulate screed temperatures and asphalt flow rates.
- Control traffic.
- Operate oil distributors, loaders, chip spreaders, dump trucks, and snow plows.
- Place strips of material, such as cork, asphalt, or steel into joints, or place rolls of expansion-joint material on machines that automatically insert material.
- Drive and operate curbing machines to extrude concrete or asphalt curbing.
- Operate machines that clean or cut expansion joints in concrete or asphalt and that rout out cracks in pavement.
- Cut or break up pavement and drive guardrail posts, using machines equipped with interchangeable hammers.
- Install dies, cutters, and extensions to screeds onto machines, using hand tools.
- Set up forms and lay out guidelines for curbs, according to written specifications, using string, spray paint, and concrete or water mixes.
- Shovel blacktop.
- Set up and tear down equipment.
- Operate machines to spread, smooth, level, or steel-reinforce stone, concrete, or asphalt on road beds.
- Operate tamping machines or manually roll surfaces to compact earth fills, foundation forms, and finished road materials, according to grade specifications.
- Cover repaired pipes with dirt, and pack backfilled excavations, using air and gasoline tampers.
- Dig out sewer lines manually, using shovels.
- Communicate with supervisors and other workers, using equipment such as wireless phones, pagers, or radio telephones.
- Drive trucks to transport crews, materials, and equipment.
- Inspect manholes to locate sewer line stoppages.
- Operate sewer cleaning equipment, including power rodders, high-velocity water jets, sewer flushers, bucket machines, wayne balls, and vac-alls.
- Prepare and keep records of actions taken, including maintenance and repair work.
- Clean and repair septic tanks, sewer lines, or related structures such as manholes, culverts, and catch basins.
- Measure excavation sites, using plumbers' snakes, tapelines, or lengths of cutting heads within sewers, and mark areas for digging.
- Service, adjust, and make minor repairs to equipment, machines, and attachments.
- Locate problems, using specially designed equipment, and mark where digging must occur to reach damaged tanks or pipes.
- Clean and disinfect domestic basements and other areas flooded by sewer stoppages.
- Withdraw cables from pipes and examine them for evidence of mud, roots, grease, and other deposits indicating broken or clogged sewer lines.
- Ensure that repaired sewer line joints are tightly sealed before backfilling begins.
- Rotate cleaning rods manually, using turning pins.
- Install rotary knives on flexible cables mounted on machine reels, according to the diameters of pipes to be cleaned.
- Start machines to feed revolving cables or rods into openings, stopping machines and changing knives to conform to pipe sizes.
- Update sewer maps and manhole charts.
- Cut damaged sections of pipe with cutters, remove broken sections from ditches, and replace pipe sections, using pipe sleeves.
- Requisition or order tools and equipment.
- Break asphalt and other pavement so that pipes can be accessed, using airhammers, picks, and shovels.
- Tap mainline sewers to install sewer saddles.
- Cover repaired pipes with dirt, and pack backfilled excavations, using air and gasoline tampers.
- Dig out sewer lines manually, using shovels.
