- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
Occupations with related tasks Save Table: XLSX CSV
| Closely Related Tasks | All Related Tasks | Job Zone | Code | Occupation |
| 9 | 9 | 2 | 47-3013.00 | Helpers--Electricians |
| 5 | 5 | 3 | 47-2111.00 | Electricians 
|
| 3 | 6 | 3 | 49-2022.00 | Telecommunications Equipment Installers and Repairers, Except Line Installers
|
| 2 | 7 | 3 | 49-2021.00 | Radio, Cellular, and Tower Equipment Installers and Repairers |
| 2 | 4 | 3 | 49-2093.00 | Electrical and Electronics Installers and Repairers, Transportation Equipment
|
| 2 | 4 | 3 | 49-2098.00 | Security and Fire Alarm Systems Installers |
| 2 | 2 | 3 | 49-2091.00 | Avionics Technicians |
| 1 | 8 | 3 | 49-9012.00 | Control and Valve Installers and Repairers, Except Mechanical Door |
| 1 | 2 | 3 | 27-4015.00 | Lighting Technicians |
| 1 | 2 | 3 | 49-2011.00 | Computer, Automated Teller, and Office Machine Repairers |
| 1 | 1 | 3 | 49-9061.00 | Camera and Photographic Equipment Repairers |
| 1 | 1 | 3 | 49-2094.00 | Electrical and Electronics Repairers, Commercial and Industrial Equipment |
| 1 | 1 | 2 | 47-2221.00 | Structural Iron and Steel Workers |
| 1 | 1 | 2 | 47-2231.00 | Solar Photovoltaic Installers
|
| 1 | 1 | 2 | 47-5044.00 | Loading and Moving Machine Operators, Underground Mining |
| 1 | 1 | 3 | 49-9071.00 | Maintenance and Repair Workers, General
|
| 1 | 1 | 3 | 49-3011.00 | Aircraft Mechanics and Service Technicians |
- Strip insulation from wire ends, using wire stripping pliers, and attach wires to terminals for subsequent soldering.
- Drill holes and pull or push wiring through openings, using hand and power tools.
- Perform semi-skilled and unskilled laboring duties related to the installation, maintenance and repair of a wide variety of electrical systems and equipment.
- Thread conduit ends, connect couplings, and fabricate and secure conduit support brackets, using hand tools.
- String transmission lines or cables through ducts or conduits, under the ground, through equipment, or to towers.
- Install copper-clad ground rods, using a manual post driver.
- Bolt component parts together to form tower assemblies, using hand tools.
- Erect electrical system components and barricades, and rig scaffolds, hoists, and shoring.
- Solder electrical connections, using soldering iron.
- Trace out short circuits in wiring, using test meter.
- Measure, cut, and bend wire and conduit, using measuring instruments and hand tools.
- Examine electrical units for loose connections and broken insulation and tighten connections, using hand tools.
- Maintain tools, vehicles, and equipment and keep parts and supplies in order.
- Clean work area and wash parts.
- Disassemble defective electrical equipment, replace defective or worn parts, and reassemble equipment, using hand tools.
- Construct controllers and panels, using power drills, drill presses, taps, saws, and punches.
- Transport tools, materials, equipment, and supplies to work site by hand, handtruck, or heavy, motorized truck.
- Dig trenches or holes for installation of conduit or supports.
- Raise, lower, or position equipment, tools, and materials, using hoist, hand line, or block and tackle.
- Trim trees and clear undergrowth along right-of-way.
- Requisition materials, using warehouse requisition or release forms.
- Paint a variety of objects related to electrical functions.
- Break up concrete, using airhammer, to facilitate installation, construction, or repair of equipment.
- Operate heavy equipment, such as backhoes.
- Operate cutting torches and welding equipment, while working with conduit and metal components to construct devices associated with electrical functions.
- Strip insulation from wire ends, using wire stripping pliers, and attach wires to terminals for subsequent soldering.
- Drill holes and pull or push wiring through openings, using hand and power tools.
- Perform semi-skilled and unskilled laboring duties related to the installation, maintenance and repair of a wide variety of electrical systems and equipment.
- Thread conduit ends, connect couplings, and fabricate and secure conduit support brackets, using hand tools.
- String transmission lines or cables through ducts or conduits, under the ground, through equipment, or to towers.
- Install copper-clad ground rods, using a manual post driver.
- Bolt component parts together to form tower assemblies, using hand tools.
- Erect electrical system components and barricades, and rig scaffolds, hoists, and shoring.
- Solder electrical connections, using soldering iron.
- Place conduit, pipes, or tubing, inside designated partitions, walls, or other concealed areas, and pull insulated wires or cables through the conduit to complete circuits between boxes.
- Assemble, install, test, or maintain electrical or electronic wiring, equipment, appliances, apparatus, or fixtures, using hand tools or power tools.
- Connect wires to circuit breakers, transformers, or other components.
- Install ground leads and connect power cables to equipment, such as motors.
- Fasten small metal or plastic boxes to walls to house electrical switches or outlets.
- Prepare sketches or follow blueprints to determine the location of wiring or equipment and to ensure conformance to building and safety codes.
- Work from ladders, scaffolds, or roofs to install, maintain, or repair electrical wiring, equipment, or fixtures.
- Use a variety of tools or equipment, such as power construction equipment, measuring devices, power tools, and testing equipment, such as oscilloscopes, ammeters, or test lamps.
- Maintain current electrician's license or identification card to meet governmental regulations.
- Plan layout and installation of electrical wiring, equipment, or fixtures, based on job specifications and local codes.
- Direct or train workers to install, maintain, or repair electrical wiring, equipment, or fixtures.
- Test electrical systems or continuity of circuits in electrical wiring, equipment, or fixtures, using testing devices, such as ohmmeters, voltmeters, or oscilloscopes, to ensure compatibility and safety of system.
- Diagnose malfunctioning systems, apparatus, or components, using test equipment and hand tools to locate the cause of a breakdown and correct the problem.
- Inspect electrical systems, equipment, or components to identify hazards, defects, or the need for adjustment or repair, and to ensure compliance with codes.
- Advise management on whether continued operation of equipment could be hazardous.
- Repair or replace wiring, equipment, or fixtures, using hand tools or power tools.
- Construct or fabricate parts, using hand tools, according to specifications.
- Provide preliminary sketches or cost estimates for materials or services.
- Perform business management duties, such as maintaining records or files, preparing reports, or ordering supplies or equipment.
- Perform physically demanding tasks, such as digging trenches to lay conduit or moving or lifting heavy objects.
- Provide assistance during emergencies by operating floodlights or generators, placing flares, or driving needed vehicles.
- Place conduit, pipes, or tubing, inside designated partitions, walls, or other concealed areas, and pull insulated wires or cables through the conduit to complete circuits between boxes.
- Assemble, install, test, or maintain electrical or electronic wiring, equipment, appliances, apparatus, or fixtures, using hand tools or power tools.
- Connect wires to circuit breakers, transformers, or other components.
- Install ground leads and connect power cables to equipment, such as motors.
- Fasten small metal or plastic boxes to walls to house electrical switches or outlets.
- Assemble and install communication equipment such as data and telephone communication lines, wiring, switching equipment, wiring frames, power apparatus, computer systems, and networks.
- Install telephone station equipment, such as intercommunication systems, transmitters, receivers, relays, and ringers, and related apparatus, such as coin collectors, telephone booths, and switching-key equipment.
- Place intercept circuits on terminals to handle vacant lines in central office installations.
- Run wires between components and to outside cable systems, connecting them to wires from telephone poles or underground cable accesses.
- Remove and remake connections to change circuit layouts, following work orders or diagrams.
- Route and connect cables and lines to switches, switchboard equipment, and distributing frames, using wire-wrap guns or soldering irons to connect wires to terminals.
- Demonstrate equipment to customers and explain its use, responding to any inquiries or complaints.
- Test circuits and components of malfunctioning telecommunications equipment to isolate sources of malfunctions, using test meters, circuit diagrams, polarity probes, and other hand tools.
- Test repaired, newly installed, or updated equipment to ensure that it functions properly and conforms to specifications, using test equipment and observation.
- Climb poles and ladders, use truck-mounted booms, and enter areas such as manholes and cable vaults to install, maintain, or inspect equipment.
- Test connections to ensure that power supplies are adequate and that communications links function.
- Note differences in wire and cable colors so that work can be performed correctly.
- Inspect equipment on a regular basis to ensure proper functioning.
- Collaborate with other workers to locate and correct malfunctions.
- Remove loose wires and other debris after work is completed.
- Repair or replace faulty equipment, such as defective and damaged telephones, wires, switching system components, and associated equipment.
- Maintain computer and manual records pertaining to facilities and equipment.
- Communicate with bases, using telephones or two-way radios to receive instructions or technical advice, or to report equipment status.
- Clean and maintain tools, test equipment, and motor vehicles.
- Perform database verifications, using computers.
- Request support from technical service centers when on-site procedures fail to solve installation or maintenance problems.
- Analyze test readings, computer printouts, and trouble reports to determine equipment repair needs and required repair methods.
- Adjust or modify equipment to enhance equipment performance or to respond to customer requests.
- Remove and replace plug-in circuit equipment.
- Refer to manufacturers' manuals to obtain maintenance instructions pertaining to specific malfunctions.
- Dig holes or trenches as necessary for equipment installation and access.
- Review manufacturer's instructions, manuals, technical specifications, building permits, and ordinances to determine communication equipment requirements and procedures.
- Drive crew trucks to and from work areas.
- Designate cables available for use.
- Diagnose and correct problems from remote locations, using special switchboards to find the sources of problems.
- Program computerized switches and switchboards to provide requested features.
- Enter codes needed to correct electronic switching system programming.
- Examine telephone transmission facilities to determine requirements for new or additional telephone services.
- Measure distances from landmarks to identify exact installation sites for equipment.
- Install updated software and programs that maintain existing software or provide requested features, such as time-correlated call routing.
- Perform routine maintenance on equipment, including adjusting and lubricating components and painting worn or exposed areas.
- Determine viability of sites through observation, and discuss site locations and construction requirements with customers.
- Clean switches and replace contact points, using vacuum hoses, solvents, and hand tools.
- Provide input into the design and manufacturing of new equipment.
- Address special issues or situations, such as illegal or unauthorized use of equipment, or cases of electrical or acoustic shock.
- Assemble and install communication equipment such as data and telephone communication lines, wiring, switching equipment, wiring frames, power apparatus, computer systems, and networks.
- Install telephone station equipment, such as intercommunication systems, transmitters, receivers, relays, and ringers, and related apparatus, such as coin collectors, telephone booths, and switching-key equipment.
- Place intercept circuits on terminals to handle vacant lines in central office installations.
- Run wires between components and to outside cable systems, connecting them to wires from telephone poles or underground cable accesses.
- Remove and remake connections to change circuit layouts, following work orders or diagrams.
- Route and connect cables and lines to switches, switchboard equipment, and distributing frames, using wire-wrap guns or soldering irons to connect wires to terminals.
- Install all necessary transmission equipment components, including antennas or antenna mounts, surge arrestors, transmission lines, connectors, or tower-mounted amplifiers (TMAs).
- Install or repair tower lighting components, including strobes, beacons, or lighting controllers.
- Run appropriate power, ground, or coaxial cables.
- Install, connect, or test underground or aboveground grounding systems.
- Insert plugs into receptacles and bolt or screw leads to terminals to connect equipment to power sources, using hand tools.
- Install, adjust, and repair stationary and mobile radio transmitting and receiving equipment and two-way radio communication systems.
- Repair circuits, wiring, and soldering, using soldering irons and hand tools to install parts and adjust connections.
- Inspect completed work to ensure all hardware is tight, antennas are level, hangers are properly fastened, proper support is in place, or adequate weather proofing has been installed.
- Test operation of tower transmission components, using sweep testing tools or software.
- Read work orders, blueprints, plans, datasheets or site drawings to determine work to be done.
- Replace existing antennas with new antennas as directed.
- Bolt equipment into place, using hand or power tools.
- Complete reports related to project status, progress, or other work details, using computer software.
- Check antenna positioning to ensure specified azimuths or mechanical tilts and adjust as necessary.
- Transport equipment to work sites, using utility trucks and equipment trailers.
- Take site survey photos or photos of work performed, using digital cameras.
- Climb towers to access components, using safety equipment, such as full-body harnesses.
- Climb communication towers to install, replace, or repair antennas or auxiliary equipment used to transmit and receive radio waves.
- Lift equipment into position, using cranes and rigging tools or equipment, such as gin poles.
- Perform maintenance or repair work on existing tower equipment, using hand or power tools.
- Locate tower sites where work is to be performed, using mapping software.
- Calibrate and align components, using scales, gauges, and other measuring instruments.
- Examine malfunctioning radio equipment to locate defects such as loose connections, broken wires, or burned-out components, using schematic diagrams and test equipment.
- Monitor radio range stations to detect transmission flaws and adjust controls to eliminate flaws.
- Mount equipment on transmission towers and in vehicles such as ships or ambulances.
- Remove and replace defective components and parts such as conductors, resistors, semiconductors, and integrated circuits, using soldering irons, wire cutters, and hand tools.
- Test batteries, using hydrometers and ammeters, and charge batteries as necessary.
- Test emergency transmitters to ensure their readiness for immediate use.
- Test equipment functions such as signal strength and quality, transmission capacity, interference, and signal delay, using equipment such as oscilloscopes, circuit analyzers, frequency meters, and wattmeters.
- Turn setscrews to adjust receivers for maximum sensitivity and transmitters for maximum output.
- Install all necessary transmission equipment components, including antennas or antenna mounts, surge arrestors, transmission lines, connectors, or tower-mounted amplifiers (TMAs).
- Install or repair tower lighting components, including strobes, beacons, or lighting controllers.
- Run appropriate power, ground, or coaxial cables.
- Install, connect, or test underground or aboveground grounding systems.
- Insert plugs into receptacles and bolt or screw leads to terminals to connect equipment to power sources, using hand tools.
- Install, adjust, and repair stationary and mobile radio transmitting and receiving equipment and two-way radio communication systems.
- Repair circuits, wiring, and soldering, using soldering irons and hand tools to install parts and adjust connections.
- Install fixtures, outlets, terminal boards, switches, and wall boxes, using hand tools.
- Install new fuses, electrical cables, or power sources as required.
- Splice wires with knives or cutting pliers, and solder connections to fixtures, outlets, and equipment.
- Measure, cut, and install frameworks and conduit to support and connect wiring, control panels, and junction boxes, using hand tools.
- Inspect and test electrical systems and equipment to locate and diagnose malfunctions, using visual inspections, testing devices, and computer software.
- Reassemble and test equipment after repairs.
- Adjust, repair, or replace defective wiring and relays in ignition, lighting, air-conditioning, and safety control systems, using electrician's tools.
- Locate and remove or repair circuit defects such as blown fuses or malfunctioning transistors.
- Maintain equipment service records.
- Refer to schematics and manufacturers' specifications that show connections and provide instructions on how to locate problems.
- Cut openings and drill holes for fixtures, outlet boxes, and fuse holders, using electric drills and routers.
- Confer with customers to determine the nature of malfunctions.
- Install electrical equipment such as air-conditioning, heating, or ignition systems and components such as generator brushes and commutators, using hand tools.
- Repair or rebuild equipment such as starters, generators, distributors, or door controls, using electrician's tools.
- Estimate costs of repairs based on parts and labor requirements.
- Install fixtures, outlets, terminal boards, switches, and wall boxes, using hand tools.
- Install new fuses, electrical cables, or power sources as required.
- Splice wires with knives or cutting pliers, and solder connections to fixtures, outlets, and equipment.
- Measure, cut, and install frameworks and conduit to support and connect wiring, control panels, and junction boxes, using hand tools.
- Install, maintain, or repair security systems, alarm devices, or related equipment, following blueprints of electrical layouts and building plans.
- Mount and fasten control panels, door and window contacts, sensors, or video cameras, and attach electrical and telephone wiring to connect components.
- Feed cables through access holes, roof spaces, or cavity walls to reach fixture outlets, positioning and terminating cables, wires, or strapping.
- Mount raceways and conduits and fasten wires to wood framing, using staplers.
- Demonstrate systems for customers and explain details, such as the causes and consequences of false alarms.
- Test and repair circuits and sensors, following wiring and system specifications.
- Examine systems to locate problems, such as loose connections or broken insulation.
- Test backup batteries, keypad programming, sirens, or other security features to ensure proper functioning or to diagnose malfunctions.
- Drill holes for wiring in wall studs, joists, ceilings, or floors.
- Inspect installation sites and study work orders, building plans, and installation manuals to determine materials requirements and installation procedures.
- Consult with clients to assess risks and to determine security requirements.
- Adjust sensitivity of units, based on room structures and manufacturers' recommendations, using programming keypads.
- Keep informed of new products and developments.
- Order replacement parts.
- Prepare documents, such as invoices or warranties.
- Provide customers with cost estimates for equipment installation.
- Install, maintain, or repair security systems, alarm devices, or related equipment, following blueprints of electrical layouts and building plans.
- Mount and fasten control panels, door and window contacts, sensors, or video cameras, and attach electrical and telephone wiring to connect components.
- Feed cables through access holes, roof spaces, or cavity walls to reach fixture outlets, positioning and terminating cables, wires, or strapping.
- Mount raceways and conduits and fasten wires to wood framing, using staplers.
- Install electrical and electronic components, assemblies, and systems in aircraft, using hand tools, power tools, or soldering irons.
- Connect components to assemblies such as radio systems, instruments, magnetos, inverters, and in-flight refueling systems, using hand tools and soldering irons.
- Test and troubleshoot instruments, components, and assemblies, using circuit testers, oscilloscopes, or voltmeters.
- Keep records of maintenance and repair work.
- Adjust, repair, or replace malfunctioning components or assemblies, using hand tools or soldering irons.
- Set up and operate ground support and test equipment to perform functional flight tests of electrical and electronic systems.
- Assemble components such as switches, electrical controls, and junction boxes, using hand tools or soldering irons.
- Lay out installation of aircraft assemblies and systems, following documentation such as blueprints, manuals, and wiring diagrams.
- Interpret flight test data to diagnose malfunctions and systemic performance problems.
- Coordinate work with that of engineers, technicians, and other aircraft maintenance personnel.
- Fabricate parts and test aids as required.
- Assemble prototypes or models of circuits, instruments, and systems for use in testing.
- Operate computer-aided drafting and design applications to design avionics system modifications.
- Install electrical and electronic components, assemblies, and systems in aircraft, using hand tools, power tools, or soldering irons.
- Connect components to assemblies such as radio systems, instruments, magnetos, inverters, and in-flight refueling systems, using hand tools and soldering irons.
- Install, inspect and test electric meters, relays, and power sources to detect causes of malfunctions and inaccuracies, using hand tools and testing equipment.
- Install regulators and related equipment such as gas meters, odorization units, and gas pressure telemetering equipment.
- Mount and install meters and other electric equipment such as time clocks, transformers, and circuit breakers, using electricians' hand tools.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Attach air hoses to meter inlets, plug outlets, and observe gauges for pressure losses to test internal seams for leaks.
- Clamp regulator units into vises on stages above water tanks, and attach compressed air hoses to intake ports.
- Splice and connect cables from meters or current transformers to pull boxes or switchboards, using hand tools.
- Connect hoses from provers to meter inlets and outlets, and raise prover bells until prover gauges register zero.
- Record maintenance information, including test results, material usage, and repairs made.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Lubricate wearing surfaces of mechanical parts, using oils or other lubricants.
- Calibrate instrumentation, such as meters, gauges, and regulators, for pressure, temperature, flow, and level.
- Test valves and regulators for leaks and accurate temperature and pressure settings, using precision testing equipment.
- Record meter readings and installation data on meter cards, work orders, or field service orders, or enter data into hand-held computers.
- Turn meters on or off to establish or close service.
- Shut off service and notify repair crews when major repairs are required, such as the replacement of underground pipes or wiring.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Turn valves to allow measured amounts of air or gas to pass through meters at specified flow rates.
- Report hazardous field situations and damaged or missing meters.
- Vary air pressure flowing into regulators and turn handles to assess functioning of valves and pistons.
- Examine valves or mechanical control device parts for defects, dents, or loose attachments, and mark malfunctioning areas of defective units.
- Investigate instances of illegal tapping into service lines.
- Trace and tag meters or house lines.
- Repair electric meters and components, such as transformers and relays, and replace metering devices, dial glasses, and faulty or incorrect wiring, using hand tools.
- Replace defective parts, such as bellows, range springs, and toggle switches, and reassemble units according to blueprints, using cam presses and hand tools.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Measure tolerances of assembled and salvageable parts for conformance to standards or specifications, using gauges, micrometers, and calipers.
- Clean internal compartments and moving parts, using rags and cleaning compounds.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Reassemble repaired equipment, and solder top, front, and back case panels in place, using soldering guns, power tools, and hand tools.
- Make adjustments to meter components, such as setscrews or timing mechanisms, so that they conform to specifications.
- Recommend and write up specifications for changes in hardware, such as house wiring.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Collect money due on delinquent accounts.
- Attach pressurized meters to fixtures which submerge them in water, and observe meters for leaks.
- Advise customers on proper installation of valves or regulators and related equipment.
- Calibrate thermostats for specified temperature or pressure settings.
- Clean plant growth, scale, paint, soil, or rust from meter housings, using wire brushes, scrapers, buffers, sandblasters, or cleaning compounds.
- Install, inspect and test electric meters, relays, and power sources to detect causes of malfunctions and inaccuracies, using hand tools and testing equipment.
- Install regulators and related equipment such as gas meters, odorization units, and gas pressure telemetering equipment.
- Mount and install meters and other electric equipment such as time clocks, transformers, and circuit breakers, using electricians' hand tools.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Attach air hoses to meter inlets, plug outlets, and observe gauges for pressure losses to test internal seams for leaks.
- Clamp regulator units into vises on stages above water tanks, and attach compressed air hoses to intake ports.
- Splice and connect cables from meters or current transformers to pull boxes or switchboards, using hand tools.
- Connect hoses from provers to meter inlets and outlets, and raise prover bells until prover gauges register zero.
- Install electrical cables or wire fixtures.
- Patch or wire lights to dimmers or other electronic consoles.
- Assess safety of wiring or equipment set-up to determine the risk of fire or electrical shock.
- Consult with lighting director or production staff to determine lighting requirements.
- Disassemble and store equipment after performances.
- Install color effects or image patterns, such as color filters, onto lighting fixtures.
- Load, unload, or position lighting equipment.
- Match light fixture settings, such as brightness and color, to lighting design plans.
- Notify supervisors when major lighting equipment repairs are needed.
- Operate manual or automated systems to control lighting throughout productions.
- Perform minor repairs or routine maintenance on lighting equipment, such as replacing lamps or damaged color filters.
- Program lighting consoles or load automated lighting control systems onto consoles.
- Set up and focus light fixtures to meet requirements of television, theater, concerts, or other productions.
- Set up scaffolding or cranes to assist with setting up of lighting equipment.
- Test lighting equipment function and desired lighting effects.
- Visit and assess structural and electrical layout of locations before setting up lighting equipment.
- Install electrical cables or wire fixtures.
- Patch or wire lights to dimmers or other electronic consoles.
- Update existing equipment, performing tasks such as installing updated circuit boards or additional memory.
- Lay cable and hook up electrical connections between machines, power sources, and phone lines.
- Reassemble machines after making repairs or replacing parts.
- Converse with customers to determine details of equipment problems.
- Disassemble machines to examine parts, such as wires, gears, or bearings for wear or defects, using hand or power tools and measuring devices.
- Advise customers concerning equipment operation, maintenance, or programming.
- Align, adjust, or calibrate equipment according to specifications.
- Repair, adjust, or replace electrical or mechanical components or parts, using hand tools, power tools, or soldering or welding equipment.
- Travel to customers' stores or offices to service machines or to provide emergency repair service.
- Maintain parts inventories and order any additional parts needed for repairs.
- Operate machines to test functioning of parts or mechanisms.
- Reinstall software programs or adjust settings on existing software to fix machine malfunctions.
- Clean, oil, or adjust mechanical parts to maintain machines' operating efficiency and to prevent breakdowns.
- Maintain records of equipment maintenance work or repairs.
- Test new systems to ensure that they are in working order.
- Complete repair bills, shop records, time cards, or expense reports.
- Install and configure new equipment, including operating software or peripheral equipment.
- Analyze equipment performance records to assess equipment functioning.
- Read specifications, such as blueprints, charts, or schematics, to determine machine settings or adjustments.
- Test components or circuits of faulty equipment to locate defects, using oscilloscopes, signal generators, ammeters, voltmeters, or special diagnostic software programs.
- Assemble machines according to specifications, using hand or power tools and measuring devices.
- Enter information into computers to copy programs from one electronic component to another or to draw, modify, or store schematics.
- Fill machines with toners, inks, or other duplicating fluids.
- Train new repairers.
- Calibrate testing instruments.
- Update existing equipment, performing tasks such as installing updated circuit boards or additional memory.
- Lay cable and hook up electrical connections between machines, power sources, and phone lines.
- Install electrical assemblies and wiring in aircraft camera housings and memory cards or film in cameras, following blueprints and using hand tools and soldering equipment.
- Adjust cameras, photographic mechanisms, or equipment such as range and view finders, shutters, light meters, or lens systems, using hand tools.
- Disassemble equipment to gain access to defect, using hand tools.
- Test equipment performance, focus of lens system, diaphragm alignment, lens mounts, or film transport, using precision gauges.
- Clean and lubricate cameras and polish camera lenses, using cleaning materials and work aids.
- Requisition parts or materials.
- Calibrate and verify accuracy of light meters, shutter diaphragm operation, or lens carriers, using timing instruments.
- Examine cameras, equipment, processed film, or laboratory reports to diagnose malfunction, using work aids and specifications.
- Read and interpret engineering drawings, diagrams, instructions, or specifications to determine needed repairs, fabrication method, and operation sequence.
- Measure parts to verify specified dimensions or settings, such as camera shutter speed or light meter reading accuracy, using measuring instruments.
- Fabricate or modify defective electronic, electrical, or mechanical components, using bench lathe, milling machine, shaper, grinder, or precision hand tools, according to specifications.
- Assemble aircraft cameras, still or motion picture cameras, photographic equipment, or frames, using diagrams, blueprints, bench machines, hand tools, or power tools.
- Record test data and document fabrication techniques on reports.
- Lay out reference points and dimensions on parts or metal stock to be machined, using precision measuring instruments.
- Recommend design changes or upgrades of microfilming, film-developing, or photographic equipment.
- Install electrical assemblies and wiring in aircraft camera housings and memory cards or film in cameras, following blueprints and using hand tools and soldering equipment.
- Install repaired equipment in various settings, such as industrial or military establishments.
- Test faulty equipment to diagnose malfunctions, using test equipment or software, and applying knowledge of the functional operation of electronic units and systems.
- Maintain equipment logs that record performance problems, repairs, calibrations, or tests.
- Set up and test industrial equipment to ensure that it functions properly.
- Inspect components of industrial equipment for accurate assembly and installation or for defects, such as loose connections or frayed wires.
- Operate equipment to demonstrate proper use or to analyze malfunctions.
- Enter information into computer to copy program or to draw, modify, or store schematics, applying knowledge of software package used.
- Perform scheduled preventive maintenance tasks, such as checking, cleaning, or repairing equipment, to detect and prevent problems.
- Calibrate testing instruments and installed or repaired equipment to prescribed specifications.
- Repair or adjust equipment, machines, or defective components, replacing worn parts, such as gaskets or seals in watertight electrical equipment.
- Consult with customers, supervisors, or engineers to plan layout of equipment or to resolve problems in system operation or maintenance.
- Maintain inventory of spare parts.
- Study blueprints, schematics, manuals, or other specifications to determine installation procedures.
- Examine work orders and converse with equipment operators to detect equipment problems and to ascertain whether mechanical or human errors contributed to the problems.
- Coordinate efforts with other workers involved in installing or maintaining equipment or components.
- Develop or modify industrial electronic devices, circuits, or equipment, according to available specifications.
- Determine feasibility of using standardized equipment or develop specifications for equipment required to perform additional functions.
- Advise management regarding customer satisfaction, product performance, or suggestions for product improvements.
- Send defective units to the manufacturer or to a specialized repair shop for repair.
- Sign overhaul documents for equipment replaced or repaired.
- Install repaired equipment in various settings, such as industrial or military establishments.
- Insert sealing strips, wiring, insulating material, ladders, flanges, gauges, or valves, depending on types of structures being assembled.
- Read specifications or blueprints to determine the locations, quantities, or sizes of materials required.
- Connect columns, beams, and girders with bolts, following blueprints and instructions from supervisors.
- Bolt aligned structural steel members in position for permanent riveting, bolting, or welding into place.
- Fasten structural steel members to hoist cables, using chains, cables, or rope.
- Hoist steel beams, girders, or columns into place, using cranes or signaling hoisting equipment operators to lift and position structural steel members.
- Verify vertical and horizontal alignment of structural steel members, using plumb bobs, laser equipment, transits, or levels.
- Cut, bend, or weld steel pieces, using metal shears, torches, or welding equipment.
- Erect metal or precast concrete components for structures, such as buildings, bridges, dams, towers, storage tanks, fences, or highway guard rails.
- Force structural steel members into final positions, using turnbuckles, crowbars, jacks, or hand tools.
- Pull, push, or pry structural steel members into approximate positions for bolting into place.
- Unload and position prefabricated steel units for hoisting, as needed.
- Drive drift pins through rivet holes to align rivet holes in structural steel members with corresponding holes in previously placed members.
- Assemble hoisting equipment or rigging, such as cables, pulleys, or hooks, to move heavy equipment or materials.
- Fabricate metal parts, such as steel frames, columns, beams, or girders, according to blueprints or instructions from supervisors.
- Dismantle structures or equipment.
- Ride on girders or other structural steel members to position them, or use rope to guide them into position.
- Hold rivets while riveters use air hammers to form heads on rivets.
- Place blocks under reinforcing bars used to reinforce floors.
- Catch hot rivets in buckets and insert rivets in holes, using tongs.
- Insert sealing strips, wiring, insulating material, ladders, flanges, gauges, or valves, depending on types of structures being assembled.
- Install module array interconnect wiring, implementing measures to disable arrays during installation.
- Install photovoltaic (PV) systems in accordance with codes and standards, using drawings, schematics, and instructions.
- Assemble solar modules, panels, or support structures, as specified.
- Apply weather sealing to array, building, or support mechanisms.
- Determine appropriate sizes, ratings, and locations for all system overcurrent devices, disconnect devices, grounding equipment, and surge suppression equipment.
- Identify methods for laying out, orienting, and mounting modules or arrays to ensure efficient installation, electrical configuration, or system maintenance.
- Identify electrical, environmental, and safety hazards associated with photovoltaic (PV) installations.
- Examine designs to determine current requirements for all parts of the photovoltaic (PV) system electrical circuit.
- Check electrical installation for proper wiring, polarity, grounding, or integrity of terminations.
- Test operating voltages to ensure operation within acceptable limits for power conditioning equipment, such as inverters and controllers.
- Identify and resolve any deficiencies in photovoltaic (PV) system installation or materials.
- Program, adjust, or configure inverters and controls for desired set points and operating modes.
- Identify installation locations with proper orientation, area, solar access, or structural integrity for photovoltaic (PV) arrays.
- Visually inspect and test photovoltaic (PV) modules or systems.
- Install required labels on solar system components and hardware.
- Determine photovoltaic (PV) system designs or configurations based on factors such as customer needs, expectations, and site conditions.
- Determine materials, equipment, and installation sequences necessary to maximize installation efficiency.
- Determine connection interfaces for additional subpanels or for connecting photovoltaic (PV) systems with utility services or other power generation sources.
- Perform routine photovoltaic (PV) system maintenance on modules, arrays, batteries, power conditioning equipment, safety systems, structural systems, weather sealing, or balance of systems equipment.
- Install active solar systems, including solar collectors, concentrators, pumps, or fans.
- Activate photovoltaic (PV) systems to verify system functionality and conformity to performance expectations.
- Demonstrate system functionality and performance, including start-up, shut-down, normal operation, and emergency or bypass operations.
- Measure and analyze system performance and operating parameters to assess operating condition of systems or equipment.
- Compile or maintain records of system operation, performance, and maintenance.
- Diagram layouts and locations for photovoltaic (PV) arrays and equipment, including existing building or site features.
- Select mechanical designs, installation equipment, or installation plans that conform to environmental, architectural, structural, site, and code requirements.
- Install module array interconnect wiring, implementing measures to disable arrays during installation.
- Handle high voltage sources and hang electrical cables.
- Drive loaded shuttle cars to ramps and move controls to discharge loads into mine cars or onto conveyors.
- Pry off loose material from roofs and move it into the paths of machines, using crowbars.
- Move trailing electrical cables clear of obstructions, using rubber safety gloves.
- Control conveyors that run the entire length of shuttle cars to distribute loads as loading progresses.
- Observe hand signals, grade stakes, or other markings when operating machines.
- Examine roadway and clear obstructions from the path of travel.
- Drive machines into piles of material blasted from working faces.
- Operate levers to move conveyor booms or shovels so that mine contents such as coal, rock, and ore can be placed into cars or onto conveyors.
- Clean, fuel, service, and perform safety checks on all equipment, and repair and replace parts as necessary.
- Clean hoppers, and clean spillage from tracks, walks, driveways, and conveyor decking.
- Oil, lubricate, and adjust conveyors, crushers, and other equipment, using hand tools and lubricating equipment.
- Monitor loading processes to ensure that materials are loaded according to specifications.
- Measure, weigh, or verify levels of rock, gravel, or other excavated material to prevent equipment overloads.
- Replace hydraulic hoses, headlight bulbs, and gathering-arm teeth.
- Stop gathering arms when cars are full.
- Move mine cars into position for loading and unloading, using pinchbars inserted under car wheels to position cars under loading spouts.
- Advance machines to gather material and convey it into cars.
- Signal workers to move loaded cars.
- Guide and stop cars by switching, applying brakes, or placing scotches, or wooden wedges, between wheels and rails.
- Observe and record car numbers, carriers, customers, tonnages, and grades and conditions of material.
- Read written instructions or confer with supervisors about schedules and materials to be moved.
- Notify switching departments to deliver specific types of cars.
- Inspect boarding and locking of open-top box cars and wedging of side-drop and hopper cars to prevent loss of material in transit.
- Maintain records of materials moved.
- Direct other workers to move stakes, place blocks, position anchors or cables, or move materials.
- Push or ride cars down slopes, or hook cars to cables and control cable drum brakes, to ease cars down inclines.
- Open and close bottom doors of cars to dump contents.
- Handle high voltage sources and hang electrical cables.
- Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.
- Perform routine maintenance, such as inspecting drives, motors, or belts, checking fluid levels, replacing filters, or doing other preventive maintenance actions.
- Inspect, operate, or test machinery or equipment to diagnose machine malfunctions.
- Adjust functional parts of devices or control instruments, using hand tools, levels, plumb bobs, or straightedges.
- Order parts, supplies, or equipment from catalogs or suppliers.
- Diagnose mechanical problems and determine how to correct them, checking blueprints, repair manuals, or parts catalogs, as necessary.
- Design new equipment to aid in the repair or maintenance of machines, mechanical equipment, or building structures.
- Clean or lubricate shafts, bearings, gears, or other parts of machinery.
- Estimate costs to repair machinery, equipment, or building structures.
- Align and balance new equipment after installation.
- Record type and cost of maintenance or repair work.
- Maintain or repair specialized equipment or machinery located in cafeterias, laundries, hospitals, stores, offices, or factories.
- Dismantle machines, equipment, or devices to access and remove defective parts, using hoists, cranes, hand tools, or power tools.
- Plan and lay out repair work, using diagrams, drawings, blueprints, maintenance manuals, or schematic diagrams.
- Install equipment to improve the energy or operational efficiency of residential or commercial buildings.
- Set up and operate machine tools to repair or fabricate machine parts, jigs, fixtures, or tools.
- Perform general cleaning of buildings or properties.
- Train or manage maintenance personnel or subcontractors.
- Fabricate or repair counters, benches, partitions, or other wooden structures, such as sheds or outbuildings.
- Paint or repair roofs, windows, doors, floors, woodwork, plaster, drywall, or other parts of building structures.
- Perform routine maintenance on boilers, such as replacing burners or hoses, installing replacement parts, or reinforcing structural weaknesses to ensure optimal boiler efficiency.
- Test and treat water supply.
- Provide groundskeeping services, such as landscaping or snow removal.
- Operate cutting torches or welding equipment to cut or join metal parts.
- Inspect used parts to determine changes in dimensional requirements, using rules, calipers, micrometers, or other measuring instruments.
- Assemble boilers at installation sites, using tools such as levels, plumb bobs, hammers, torches, or other hand tools.
- Lay brick to repair or maintain buildings, walls, arches, or other structures.
- Position, attach, or blow insulating materials to prevent energy losses from buildings, pipes, or other structures or objects.
- Grind and reseat valves, using valve-grinding machines.
- Repair machines, equipment, or structures, using tools such as hammers, hoists, saws, drills, wrenches, or equipment such as precision measuring instruments or electrical or electronic testing devices.
- Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.
- Assemble and install electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools.
- Examine and inspect aircraft components, including landing gear, hydraulic systems, and deicers to locate cracks, breaks, leaks, or other problems.
- Conduct routine and special inspections as required by regulations.
- Inspect completed work to certify that maintenance meets standards and that aircraft are ready for operation.
- Read and interpret maintenance manuals, service bulletins, and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.
- Maintain repair logs, documenting all preventive and corrective aircraft maintenance.
- Modify aircraft structures, space vehicles, systems, or components, following drawings, schematics, charts, engineering orders, and technical publications.
- Inspect airframes for wear or other defects.
- Measure parts for wear, using precision instruments.
- Obtain fuel and oil samples and check them for contamination.
- Maintain, repair, and rebuild aircraft structures, functional components, and parts, such as wings and fuselage, rigging, hydraulic units, oxygen systems, fuel systems, electrical systems, gaskets, or seals.
- Replace or repair worn, defective, or damaged components, using hand tools, gauges, and testing equipment.
- Read and interpret pilots' descriptions of problems to diagnose causes.
- Test operation of engines and other systems, using test equipment, such as ignition analyzers, compression checkers, distributor timers, or ammeters.
- Measure the tension of control cables.
- Spread plastic film over areas to be repaired to prevent damage to surrounding areas.
- Remove or install aircraft engines, using hoists or forklift trucks.
- Locate and mark dimensions and reference lines on defective or replacement parts, using templates, scribes, compasses, and steel rules.
- Fabricate defective sections or parts, using metal fabricating machines, saws, brakes, shears, and grinders.
- Reassemble engines following repair or inspection and reinstall engines in aircraft.
- Service and maintain aircraft and related apparatus by performing activities such as flushing crankcases, cleaning screens, and or moving parts.
- Clean, refuel, and change oil in line service aircraft.
- Trim and shape replacement body sections to specified sizes and fits and secure sections in place, using adhesives, hand tools, and power tools.
- Accompany aircraft on flights to make in-flight adjustments and corrections.
- Remove or cut out defective parts or drill holes to gain access to internal defects or damage, using drills and punches.
- Install and align repaired or replacement parts for subsequent riveting or welding, using clamps and wrenches.
- Inventory and requisition or order supplies, parts, materials, and equipment.
- Clean, strip, prime, and sand structural surfaces and materials to prepare them for bonding.
- Communicate with other workers to coordinate fitting and alignment of heavy parts, or to facilitate processing of repair parts.
- Examine engines through specially designed openings while working from ladders or scaffolds, or use hoists or lifts to remove the entire engine from an aircraft.
- Check for corrosion, distortion, and invisible cracks in the fuselage, wings, and tail, using x-ray and magnetic inspection equipment.
- Disassemble engines and inspect parts, such as turbine blades or cylinders, for corrosion, wear, warping, cracks, and leaks, using precision measuring instruments, x-rays, and magnetic inspection equipment.
- Cure bonded structures, using portable or stationary curing equipment.
- Listen to operating engines to detect and diagnose malfunctions, such as sticking or burned valves.
- Clean engines, sediment bulk and screens, and carburetors, adjusting carburetor float levels.
- Determine repair limits for engine hot section parts.
- Remove, inspect, repair, and install in-flight refueling stores and external fuel tanks.
- Prepare and paint aircraft surfaces.
- Assemble and install electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools.
