- Weigh clay, and mix with water and chemicals to make drilling mud.
Occupations with related tasks Save Table: XLSX CSV
| Closely Related Tasks | All Related Tasks | Job Zone | Code | Occupation |
| 3 | 3 | 2 | 47-2044.00 | Tile and Stone Setters 
|
| 3 | 3 | 2 | 47-2053.00 | Terrazzo Workers and Finishers |
| 3 | 3 | 2 | 47-2121.00 | Glaziers |
| 2 | 2 | 2 | 47-2021.00 | Brickmasons and Blockmasons |
| 2 | 2 | 1 | 47-5011.00 | Derrick Operators, Oil and Gas |
| 2 | 2 | 2 | 47-2041.00 | Carpet Installers |
| 2 | 2 | 2 | 47-2142.00 | Paperhangers |
| 2 | 2 | 2 | 47-2081.00 | Drywall and Ceiling Tile Installers |
| 2 | 2 | 2 | 47-2031.00 | Carpenters |
| 2 | 2 | 2 | 47-2061.00 | Construction Laborers
|
| 1 | 1 | 2 | 47-2131.00 | Insulation Workers, Floor, Ceiling, and Wall |
| 1 | 1 | 1 | 47-3014.00 | Helpers--Painters, Paperhangers, Plasterers, and Stucco Masons |
| 1 | 1 | 2 | 47-2132.00 | Insulation Workers, Mechanical |
| 1 | 1 | 2 | 47-2042.00 | Floor Layers, Except Carpet, Wood, and Hard Tiles
|
| 1 | 1 | 2 | 47-3011.00 | Helpers--Brickmasons, Blockmasons, Stonemasons, and Tile and Marble Setters |
| 1 | 1 | 2 | 47-3015.00 | Helpers--Pipelayers, Plumbers, Pipefitters, and Steamfitters |
| 1 | 1 | 1 | 47-2161.00 | Plasterers and Stucco Masons |
| 1 | 1 | 1 | 47-5071.00 | Roustabouts, Oil and Gas |
| 1 | 1 | 2 | 47-2082.00 | Tapers |
| 1 | 1 | 3 | 47-2011.00 | Boilermakers |
| 1 | 1 | 3 | 47-2022.00 | Stonemasons |
| 1 | 1 | 2 | 47-3012.00 | Helpers--Carpenters |
| 1 | 1 | 2 | 47-3016.00 | Helpers--Roofers |
| 1 | 1 | 2 | 47-4051.00 | Highway Maintenance Workers
|
| 1 | 1 | 2 | 47-2141.00 | Painters, Construction and Maintenance |
| 1 | 1 | 2 | 47-4031.00 | Fence Erectors |
| 1 | 1 | 2 | 53-7061.00 | Cleaners of Vehicles and Equipment |
| 1 | 1 | 3 | 47-4041.00 | Hazardous Materials Removal Workers |
| 1 | 1 | 2 | 47-2211.00 | Sheet Metal Workers |
| 1 | 1 | 2 | 47-3013.00 | Helpers--Electricians |
| 1 | 1 | 1 | 47-2051.00 | Cement Masons and Concrete Finishers |
| 1 | 1 | 3 | 47-2152.00 | Plumbers, Pipefitters, and Steamfitters |
- Mix, apply, and spread plaster, concrete, mortar, cement, mastic, glue or other adhesives to form a bed for the tiles, using brush, trowel and screed.
- Mix and apply mortar or cement to edges and ends of drain tiles to seal halves and joints.
- Measure and cut metal lath to size for walls and ceilings, using tin snips.
- Align and straighten tile using levels, squares, and straightedges.
- Finish and dress the joints and wipe excess grout from between tiles, using damp sponge.
- Cut and shape tile to fit around obstacles and into odd spaces and corners, using hand and power cutting tools.
- Determine and implement the best layout to achieve a desired pattern.
- Study blueprints and examine surface to be covered to determine amount of material needed.
- Measure and mark surfaces to be tiled, following blueprints.
- Lay and set mosaic tiles to create decorative wall, mural, and floor designs.
- Apply mortar to tile back, position the tile, and press or tap with trowel handle to affix tile to base.
- Apply a sealer to make grout stain- and water-resistant.
- Level concrete and allow to dry.
- Install and anchor fixtures in designated positions, using hand tools.
- Prepare surfaces for tiling by attaching lath or waterproof paper, or by applying a cement mortar coat to a metal screen.
- Remove and replace cracked or damaged tile.
- Cut tile backing to required size, using shears.
- Remove any old tile, grout and adhesive using chisels and scrapers and clean the surface carefully.
- Cut, surface, polish, and install marble and granite or install pre-cast terrazzo, granite or marble units.
- Spread mastic or other adhesive base on roof deck to form base for promenade tile, using serrated spreader.
- Assist customers in selection of tile and grout.
- Prepare cost and labor estimates, based on calculations of time and materials needed for project.
- Brush glue onto manila paper on which design has been drawn and position tiles, finished side down, onto paper.
- Select and order tile and other items to be installed, such as bathroom accessories, walls, panels, and cabinets, according to specifications.
- Build underbeds and install anchor bolts, wires, and brackets.
- Mix, apply, and spread plaster, concrete, mortar, cement, mastic, glue or other adhesives to form a bed for the tiles, using brush, trowel and screed.
- Mix and apply mortar or cement to edges and ends of drain tiles to seal halves and joints.
- Measure and cut metal lath to size for walls and ceilings, using tin snips.
- Measure designated amounts of ingredients for terrazzo or grout, according to standard formulas and specifications, using graduated containers and scales, and load ingredients into portable mixer.
- Blend marble chip mixtures, place into panels, and push a roller over the surface to embed the chips.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Grind surfaces with a power grinder, or polish surfaces with polishing or surfacing machines.
- Cut metal division strips and press them into the terrazzo base for joints or changes of color to form designs or patterns or to help prevent cracks.
- Modify mixing, grouting, grinding, or cleaning procedures, according to type of installation or material used.
- Spread, level, or smooth concrete or terrazzo mixtures to form bases or finished surfaces, using rakes, shovels, hand or power trowels, hand or power screeds, or floats.
- Grind curved surfaces or areas inaccessible to surfacing machine, such as stairways or cabinet tops, with portable hand grinder.
- Wash polished terrazzo surface, using cleaner and water, and apply sealer and curing agent according to manufacturer's specifications, using brush or sprayer.
- Position and secure moisture membrane and wire mesh in preparation for pouring base materials for terrazzo installation.
- Fill slight grinding depressions with matching grout material and hand-trowel for a smooth, uniform surface.
- Clean installation site, mixing and storage areas, tools, machines, and equipment, and store materials and equipment.
- Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth with a trowel.
- Chip, scrape, or grind high spots, ridges, or rough projections to finish concrete, using pneumatic chisel, hand chisel, or other hand tools.
- Mold expansion joints and edges, using edging tools, jointers, or straightedges.
- Move terrazzo installation materials, tools, machines, or work devices to work areas, manually or using wheelbarrow.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Repair concrete by cutting out damaged areas, drilling holes for reinforcing rods, and positioning reinforcing rods, using power saw and drill.
- Precast terrazzo blocks in wooden forms.
- Wet concrete surface and rub with stone to smooth surface and obtain specified finish.
- Build wooden molds, clamping molds around areas to be repaired, or setting up frames to the proper depth and alignment.
- Spread roofing paper on surface of foundation and spread concrete onto roofing paper with trowel to form terrazzo base.
- Produce rough concrete surface, using broom.
- Remove frames when the foundation is dry.
- Signal truck driver to position truck to facilitate pouring concrete and move chute to direct concrete on forms.
- Measure designated amounts of ingredients for terrazzo or grout, according to standard formulas and specifications, using graduated containers and scales, and load ingredients into portable mixer.
- Blend marble chip mixtures, place into panels, and push a roller over the surface to embed the chips.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Measure mirrors and dimensions of areas to be covered to determine work procedures.
- Measure and mark outlines or patterns on glass to indicate cutting lines.
- Measure, cut, fit, and press anti-glare adhesive film to glass or spray glass with tinting solution to prevent light glare.
- Read and interpret blueprints or specifications to determine size, shape, color, type, or thickness of glass, location of framing, installation procedures, or staging or scaffolding materials required.
- Determine plumb of walls or ceilings, using plumb lines and levels.
- Install pre-assembled metal or wood frameworks for windows or doors to be fitted with glass panels, using hand tools.
- Fabricate or install metal sashes or moldings for glass installation, using aluminum or steel framing.
- Operate cranes or hoists with suction cups to lift large, heavy pieces of glass.
- Set glass doors into frames and bolt metal hinges, handles, locks, or other hardware to attach doors to frames and walls.
- Cut, fit, install, repair, or replace glass or glass substitutes, such as plastic or aluminum, in building interiors or exteriors or in furniture or other products.
- Drive trucks to installation sites and unload mirrors, glass equipment, or tools.
- Load and arrange glass or mirrors onto delivery trucks, using suction cups or cranes to lift glass.
- Cut and attach mounting strips, metal or wood moldings, rubber gaskets, or metal clips to surfaces in preparation for mirror installation.
- Pack spaces between moldings and glass with glazing compounds and trim excess material with glazing knives.
- Assemble, erect, or dismantle scaffolds, rigging, or hoisting equipment.
- Cut and remove broken glass prior to installing replacement glass.
- Secure mirrors in position, using mastic cement, putty, bolts, or screws.
- Grind or polish glass, smoothing edges when necessary.
- Fasten glass panes into wood sashes or frames with clips, points, or moldings, adding weather seals or putty around pane edges to seal joints.
- Score glass with cutters' wheels, breaking off excess glass by hand or with notched tools.
- Cut, assemble, fit, or attach metal-framed glass enclosures for showers, bathtubs, display cases, skylights, solariums, or other structures.
- Prepare glass for cutting by resting it on rack edges or against cutting tables and brushing thin layer of oil along cutting lines or dipping cutting tools in oil.
- Move furniture to clear work sites and cover floors or furnishings with drop cloths.
- Confer with customers to determine project requirements or to provide cost estimates.
- Select the type or color of glass or mirror according to specifications.
- Assemble and cement sections of stained glass together.
- Create patterns on glass by etching, sandblasting, or painting designs.
- Measure mirrors and dimensions of areas to be covered to determine work procedures.
- Measure and mark outlines or patterns on glass to indicate cutting lines.
- Measure, cut, fit, and press anti-glare adhesive film to glass or spray glass with tinting solution to prevent light glare.
- Measure distance from reference points and mark guidelines to lay out work, using plumb bobs and levels.
- Mix specified amounts of sand, clay, dirt, or mortar powder with water to form refractory mixtures.
- Construct corners by fastening in plumb position a corner pole or building a corner pyramid of bricks, and filling in between the corners using a line from corner to corner to guide each course, or layer, of brick.
- Apply and smooth mortar or other mixture over work surface.
- Calculate angles and courses and determine vertical and horizontal alignment of courses.
- Break or cut bricks, tiles, or blocks to size, using trowel edge, hammer, or power saw.
- Interpret blueprints and drawings to determine specifications and to calculate the materials required.
- Remove excess mortar with trowels and hand tools, and finish mortar joints with jointing tools, for a sealed, uniform appearance.
- Fasten or fuse brick or other building material to structure with wire clamps, anchor holes, torch, or cement.
- Clean working surface to remove scale, dust, soot, or chips of brick and mortar, using broom, wire brush, or scraper.
- Examine brickwork or structure to determine need for repair.
- Remove burned or damaged brick or mortar, using sledgehammer, crowbar, chipping gun, or chisel.
- Lay and align bricks, blocks, or tiles to build or repair structures or high temperature equipment, such as cupola, kilns, ovens, or furnaces.
- Spray or spread refractory material over brickwork to protect against deterioration.
- Measure distance from reference points and mark guidelines to lay out work, using plumb bobs and levels.
- Mix specified amounts of sand, clay, dirt, or mortar powder with water to form refractory mixtures.
- Control the viscosity and weight of the drilling fluid.
- Weigh clay, and mix with water and chemicals to make drilling mud, using portable mixers.
- Inspect derricks, or order their inspection, prior to being raised or lowered.
- Inspect derricks for flaws, and clean and oil derricks to maintain proper working conditions.
- Repair pumps, mud tanks, and related equipment.
- Set and bolt crown blocks to posts at tops of derricks.
- Listen to mud pumps and check regularly for vibration and other problems to ensure that rig pumps and drilling mud systems are working properly.
- Start pumps that circulate mud through drill pipes and boreholes to cool drill bits and flush out drill cuttings.
- Position and align derrick elements, using harnesses and platform climbing devices.
- Supervise crew members, and provide assistance in training them.
- Guide lengths of pipe into and out of elevators.
- Prepare mud reports, and instruct crews about the handling of any chemical additives.
- Clamp holding fixtures on ends of hoisting cables.
- String cables through pulleys and blocks.
- Steady pipes during connection to or disconnection from drill or casing strings.
- Control the viscosity and weight of the drilling fluid.
- Weigh clay, and mix with water and chemicals to make drilling mud, using portable mixers.
- Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting.
- Measure, cut and install tackless strips along the baseboard or wall.
- Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly.
- Join edges of carpet and seam edges where necessary, by sewing or by using tape with glue and heated carpet iron.
- Cut and trim carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer.
- Plan the layout of the carpet, allowing for expected traffic patterns and placing seams for best appearance and longest wear.
- Stretch carpet to align with walls and ensure a smooth surface, and press carpet in place over tack strips or use staples, tape, tacks or glue to hold carpet in place.
- Take measurements and study floor sketches to calculate the area to be carpeted and the amount of material needed.
- Install carpet on some floors using adhesive, following prescribed method.
- Clean up before and after installation, including vacuuming carpet and discarding remnant pieces.
- Nail tack strips around area to be carpeted or use old strips to attach edges of new carpet.
- Cut carpet padding to size and install padding, following prescribed method.
- Fasten metal treads across door openings or where carpet meets flooring to hold carpet in place.
- Draw building diagrams and record dimensions.
- Move furniture from area to be carpeted and remove old carpet and padding.
- Cut and bind material.
- Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting.
- Measure, cut and install tackless strips along the baseboard or wall.
- Measure and cut strips from rolls of wallpaper or fabric, using shears or razors.
- Mix paste, using paste powder and water, and brush paste onto surfaces.
- Smooth strips or sections of paper with brushes or rollers to remove wrinkles and bubbles and to smooth joints.
- Trim rough edges from strips, using straightedges and trimming knives.
- Trim excess material at ceilings or baseboards, using knives.
- Check finished wallcoverings for proper alignment, pattern matching, and neatness of seams.
- Mark vertical guidelines on walls to align strips, using plumb bobs and chalk lines.
- Cover interior walls and ceilings of rooms with decorative wallpaper or fabric, using hand tools.
- Apply adhesives to the backs of paper strips, using brushes, or dunk strips of prepasted wallcovering in water, wiping off any excess adhesive.
- Place strips or sections of paper on surfaces, aligning section edges and patterns.
- Fill holes, cracks, and other surface imperfections preparatory to covering surfaces.
- Measure surfaces or review work orders to estimate the quantities of materials needed.
- Apply sizing to seal surfaces and maximize adhesion of coverings to surfaces.
- Smooth rough spots on walls and ceilings, using sandpaper.
- Set up equipment, such as pasteboards and scaffolds.
- Remove old paper, using water, steam machines, or solvents and scrapers.
- Apply thinned glue to waterproof porous surfaces, using brushes, rollers, or pasting machines.
- Staple or tack advertising posters onto fences, walls, billboards, or poles.
- Remove paint, varnish, dirt, and grease from surfaces, using paint remover and water soda solutions.
- Apply acetic acid to damp plaster to prevent lime from bleeding through paper.
- Measure and cut strips from rolls of wallpaper or fabric, using shears or razors.
- Mix paste, using paste powder and water, and brush paste onto surfaces.
- Measure and mark surfaces to lay out work, according to blueprints or drawings, using tape measures, straightedges or squares, and marking devices.
- Measure and cut openings in panels or tiles for electrical outlets, windows, vents, plumbing, or other fixtures, using keyhole saws or other cutting tools.
- Read blueprints or other specifications to determine methods of installation, work procedures, or material or tool requirements.
- Fit and fasten wallboard or drywall into position on wood or metal frameworks, using glue, nails, or screws.
- Assemble or install metal framing or decorative trim for windows, doorways, or vents.
- Cut metal or wood framing and trim to size, using cutting tools.
- Inspect furrings, mechanical mountings, or masonry surfaces for plumbness and level, using spirit or water levels.
- Cut fixture or border tiles to size, using keyhole saws, and insert them into surrounding frameworks.
- Cut and screw together metal channels to make floor or ceiling frames, according to plans for the location of rooms or hallways.
- Hang drywall panels on metal frameworks of walls and ceilings in offices, schools, or other large buildings, using lifts or hoists to adjust panel heights, when necessary.
- Trim rough edges from wallboard to maintain even joints, using knives.
- Suspend angle iron grids or channel irons from ceilings, using wire.
- Coordinate work with drywall finishers who cover the seams between drywall panels.
- Install horizontal and vertical metal or wooden studs to frames so that wallboard can be attached to interior walls.
- Scribe and cut edges of tile to fit walls where wall molding is not specified.
- Hang dry lines to wall moldings to guide positioning of main runners.
- Fasten metal or rockboard lath to the structural framework of walls, ceilings, or partitions of buildings, using nails, screws, staples, or wire-ties.
- Install blanket insulation between studs and tack plastic moisture barriers over insulation.
- Seal joints between ceiling tiles and walls.
- Remove existing plaster, drywall, or paneling, using crowbars and hammers.
- Apply or mount acoustical tile or blocks, strips, or sheets of shock-absorbing materials to ceilings or walls of buildings to reduce reflection of sound or to decorate rooms.
- Mount tile, using adhesives, or by nailing, screwing, stapling, or wire-tying lath directly to structural frameworks.
- Nail channels or wood furring strips to surfaces to provide mounting for tile.
- Install metal lath where plaster applications will be exposed to weather or water, or for curved or irregular surfaces.
- Apply cement to backs of tiles and press tiles into place, aligning them with layout marks or joints of previously laid tile.
- Wash concrete surfaces before mounting tile to increase adhesive qualities of surfaces, using washing soda and zinc sulfate solution.
- Measure and mark surfaces to lay out work, according to blueprints or drawings, using tape measures, straightedges or squares, and marking devices.
- Measure and cut openings in panels or tiles for electrical outlets, windows, vents, plumbing, or other fixtures, using keyhole saws or other cutting tools.
- Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
- Perform minor plumbing, welding, or concrete mixing work.
- Follow established safety rules and regulations and maintain a safe and clean environment.
- Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue.
- Study specifications in blueprints, sketches, or building plans to prepare project layout and determine dimensions and materials required.
- Shape or cut materials to specified measurements, using hand tools, machines, or power saws.
- Verify trueness of structure, using plumb bob and level.
- Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.
- Erect scaffolding or ladders for assembling structures above ground level.
- Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.
- Maintain records, document actions, and present written progress reports.
- Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.
- Maintain job records and schedule work crew.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Bore boltholes in timber, masonry or concrete walls, using power drill.
- Install rough door and window frames, subflooring, fixtures, or temporary supports in structures undergoing construction or repair.
- Dig or direct digging of post holes and set poles to support structures.
- Cover subfloors with building paper to keep out moisture and lay hardwood, parquet, or wood-strip-block floors by nailing floors to subfloor or cementing them to mastic or asphalt base.
- Construct forms or chutes for pouring concrete.
- Arrange for subcontractors to deal with special areas, such as heating or electrical wiring work.
- Build or repair cabinets, doors, frameworks, floors, or other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, or power tools.
- Finish surfaces of woodwork or wallboard in houses or buildings, using paint, hand tools, or paneling.
- Select and order lumber or other required materials.
- Work with or remove hazardous material.
- Fill cracks or other defects in plaster or plasterboard and sand patch, using patching plaster, trowel, and sanding tool.
- Prepare cost estimates for clients or employers.
- Apply shock-absorbing, sound-deadening, or decorative paneling to ceilings or walls.
- Examine structural timbers and supports to detect decay, and replace timbers as required, using hand tools, nuts, and bolts.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
- Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
- Perform minor plumbing, welding, or concrete mixing work.
- Mix ingredients to create compounds for covering or cleaning surfaces.
- Mix, pour, or spread concrete, using portable cement mixers.
- Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.
- Lubricate, clean, or repair machinery, equipment, or tools.
- Signal equipment operators to facilitate alignment, movement, or adjustment of machinery, equipment, or materials.
- Read plans, instructions, or specifications to determine work activities.
- Measure, mark, or record openings or distances to layout areas where construction work will be performed.
- Clean or prepare construction sites to eliminate possible hazards.
- Dig ditches or trenches, backfill excavations, or compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, or rakes.
- Load, unload, or identify building materials, machinery, or tools, distributing them to the appropriate locations, according to project plans or specifications.
- Position, join, align, or seal structural components, such as concrete wall sections or pipes.
- Perform site activities required of green certified construction practices, such as implementing waste management procedures, identifying materials for reuse, or installing erosion or sedimentation control mechanisms.
- Control traffic passing near, in, or around work zones.
- Install sewer, water, or storm drain pipes, using pipe-laying machinery or laser guidance equipment.
- Operate or maintain air monitoring or other sampling devices in confined or hazardous environments.
- Smooth or finish freshly poured cement or concrete, using floats, trowels, screeds, or powered cement finishing tools.
- Erect or dismantle scaffolding, shoring, braces, traffic barricades, ramps, or other temporary structures.
- Provide assistance to craft workers, such as carpenters, plasterers, or masons.
- Perform building weatherization tasks, such as repairing windows, adding insulation, or applying weather-stripping materials.
- Apply weather-stripping to reduce energy loss.
- Spray materials, such as water, sand, steam, vinyl, paint, or stucco, through hoses to clean, coat, or seal surfaces.
- Raze buildings or salvage useful materials.
- Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.
- Position or dismantle forms for pouring concrete, using saws, hammers, nails, or bolts.
- Grind, scrape, sand, or polish surfaces, such as concrete, marble, terrazzo, or wood flooring, using abrasive tools or machines.
- Place, consolidate, or protect case-in-place concrete or masonry structures.
- Operate jackhammers or drills to break up concrete or pavement.
- Apply caulking compounds by hand or caulking guns to protect against entry of water or air.
- Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings or walls.
- Identify, pack, or transport hazardous or radioactive materials.
- Use computers or other input devices to control robotic pipe cutters or cleaners.
- Perform construction laborer duties at green building sites, such as renewable energy plants or wind turbine installations.
- Mix ingredients to create compounds for covering or cleaning surfaces.
- Mix, pour, or spread concrete, using portable cement mixers.
- Measure and cut insulation for covering surfaces, using tape measures, handsaws, power saws, knives, or scissors.
- Fit, wrap, staple, or glue insulating materials to structures or surfaces, using hand tools or wires.
- Cover and line structures with blown or rolled forms of materials to insulate against cold, heat, or moisture, using saws, knives, rasps, trowels, blowers, or other tools and implements.
- Distribute insulating materials evenly into small spaces within floors, ceilings, or walls, using blowers and hose attachments, or cement mortars.
- Move controls, buttons, or levers to start blowers and regulate flow of materials through nozzles.
- Fill blower hoppers with insulating materials.
- Cover, seal, or finish insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement or asphalt mastic.
- Read blueprints, and select appropriate insulation, based on space characteristics and the heat retaining or excluding characteristics of the material.
- Remove old insulation, such as asbestos, following safety procedures.
- Prepare surfaces for insulation application by brushing or spreading on adhesives, cement, or asphalt, or by attaching metal pins to surfaces.
- Measure and cut insulation for covering surfaces, using tape measures, handsaws, power saws, knives, or scissors.
- Mix plaster, and carry plaster to plasterers.
- Clean work areas and equipment.
- Perform support duties to assist painters, paperhangers, plasterers, or masons.
- Apply protective coverings, such as masking tape, to articles or areas that could be damaged or stained by work processes.
- Erect scaffolding.
- Fill cracks or breaks in surfaces of plaster articles or areas with putty or epoxy compounds.
- Supply or hold tools and materials.
- Smooth surfaces of articles to be painted, using sanding and buffing tools and equipment.
- Place articles to be stripped into stripping tanks.
- Remove articles such as cabinets, metal furniture, and paint containers from stripping tanks after prescribed periods of time.
- Pour specified amounts of chemical solutions into stripping tanks.
- Mix plaster, and carry plaster to plasterers.
- Measure and cut insulation for covering surfaces, using tape measures, handsaws, knives, and scissors.
- Apply, remove, and repair insulation on industrial equipment, pipes, ductwork, or other mechanical systems such as heat exchangers, tanks, and vessels, to help control noise and maintain temperatures.
- Select appropriate insulation, such as fiberglass, Styrofoam, or cork, based on the heat retaining or excluding characteristics of the material.
- Fit insulation around obstructions, and shape insulating materials and protective coverings as required.
- Determine the amounts and types of insulation needed, and methods of installation, based on factors such as location, surface shape, and equipment use.
- Cover, seal, or finish insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement, or asphalt mastic.
- Install sheet metal around insulated pipes with screws to protect the insulation from weather conditions or physical damage.
- Read blueprints and specifications to determine job requirements.
- Prepare surfaces for insulation application by brushing or spreading on adhesives, cement, or asphalt, or by attaching metal pins to surfaces.
- Distribute insulating materials evenly into small spaces within floors, ceilings, or walls, using blowers and hose attachments or cement mortar.
- Remove or seal off old asbestos insulation, following safety procedures.
- Fill blower hoppers with insulating materials.
- Move controls, buttons, or levers to start blowers, and to regulate flow of materials through nozzles.
- Measure and cut insulation for covering surfaces, using tape measures, handsaws, knives, and scissors.
- Measure and mark guidelines on surfaces or foundations, using chalk lines and dividers.
- Sweep, scrape, sand, or chip dirt and irregularities to clean base surfaces, correcting imperfections that may show through the covering.
- Cut flooring material to fit around obstructions.
- Inspect surface to be covered to ensure that it is firm and dry.
- Trim excess covering materials, tack edges, and join sections of covering material to form tight joint.
- Form a smooth foundation by stapling plywood or Masonite over the floor or by brushing waterproof compound onto surface and filling cracks with plaster, putty, or grout to seal pores.
- Cut covering and foundation materials, according to blueprints and sketches.
- Roll and press sheet wall and floor covering into cement base to smooth and finish surface, using hand roller.
- Apply adhesive cement to floor or wall material to join and adhere foundation material.
- Determine traffic areas and decide location of seams.
- Lay out, position, and apply shock-absorbing, sound-deadening, or decorative coverings to floors, walls, and cabinets, following guidelines to keep courses straight and create designs.
- Remove excess cement to clean finished surface.
- Disconnect and remove appliances, light fixtures, and worn floor and wall covering from floors, walls, and cabinets.
- Heat and soften floor covering materials to patch cracks or fit floor coverings around irregular surfaces, using blowtorch.
- Measure and mark guidelines on surfaces or foundations, using chalk lines and dividers.
- Mix mortar, plaster, and grout, manually or using machines, according to standard formulas.
- Erect scaffolding or other installation structures.
- Cut materials to specified sizes for installation, using power saws or tile cutters.
- Modify material moving, mixing, grouting, grinding, polishing, or cleaning procedures, according to installation or material requirements.
- Transport materials, tools, or machines to installation sites, manually or using conveyance equipment.
- Provide assistance in the preparation, installation, repair, or rebuilding of tile, brick, or stone surfaces.
- Locate and supply materials to masons for installation, following drawings or numbered sequences.
- Arrange or store materials, machines, tools, or equipment.
- Clean installation surfaces, equipment, tools, work sites, or storage areas, using water, chemical solutions, oxygen lances, or polishing machines.
- Move or position materials such as marble slabs, using cranes, hoists, or dollies.
- Remove excess grout or residue from tile or brick joints, using sponges or trowels.
- Apply grout between joints of bricks or tiles, using grouting trowels.
- Apply caulk, sealants, or other agents to installed surfaces.
- Remove damaged tile, brick, or mortar, and clean or prepare surfaces, using pliers, hammers, chisels, drills, wire brushes, or metal wire anchors.
- Correct surface imperfections or fill chipped, cracked, or broken bricks or tiles, using fillers, adhesives, or grouting materials.
- Mix mortar, plaster, and grout, manually or using machines, according to standard formulas.
- Measure, cut, thread and assemble new pipe, placing the assembled pipe in hangers or other supports.
- Cut or drill holes in walls or floors to accommodate the passage of pipes.
- Perform rough-ins, repair and replace fixtures and water heaters, and locate, repair, or remove leaking or broken pipes.
- Assist pipe fitters in the layout, assembly, and installation of piping for air, ammonia, gas, and water systems.
- Cut pipe and lift up to fitters.
- Fit or assist in fitting valves, couplings, or assemblies to tanks, pumps, or systems, using hand tools.
- Requisition tools and equipment, select type and size of pipe, and collect and transport materials and equipment to work site.
- Mount brackets and hangers on walls and ceilings to hold pipes, and set sleeves or inserts to provide support for pipes.
- Excavate and grade ditches, and lay and join pipe for water and sewer service.
- Disassemble and remove damaged or worn pipe.
- Clean shop, work area, and machines, using solvent and rags.
- Install gas burners to convert furnaces from wood, coal, or oil.
- Fill pipes with sand or resin to prevent distortion, and hold pipes during bending and installation.
- Immerse pipe in chemical solution to remove dirt, oil, and scale.
- Clean and renew steam traps.
- Measure, cut, thread and assemble new pipe, placing the assembled pipe in hangers or other supports.
- Mix mortar and plaster to desired consistency or direct workers who perform mixing.
- Cover surfaces such as windows, doors, or sidewalks to protect from splashing.
- Clean job sites.
- Apply coats of plaster or stucco to walls, ceilings, or partitions of buildings, using trowels, brushes, or spray guns.
- Set up scaffolds.
- Determine materials needed to complete the job and place orders accordingly.
- Apply weatherproof, decorative coverings to exterior surfaces of buildings, such as by troweling or spraying on coats of stucco.
- Clean and prepare surfaces for applications of plaster, cement, stucco, or similar materials, such as by drywall taping.
- Create decorative textures in finish coat, using brushes or trowels, sand, pebbles, or stones.
- Apply insulation to building exteriors by installing prefabricated insulation systems over existing walls or by covering the outer wall with insulation board, reinforcing mesh, and a base coat.
- Rough the undercoat surface with a scratcher so the finish coat will adhere.
- Cure freshly plastered surfaces.
- Install guide wires on exterior surfaces of buildings to indicate thickness of plaster or stucco and nail wire mesh, lath, or similar materials to the outside surface to hold stucco in place.
- Spray acoustic materials or texture finish over walls or ceilings.
- Mold or install ornamental plaster pieces, panels, or trim.
- Mix mortar and plaster to desired consistency or direct workers who perform mixing.
- Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.
- Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.
- Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.
- Guide cranes to move loads about decks.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Lay gas and oil pipelines.
- Bolt together pump and engine parts.
- Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.
- Clean trucks used in the fields.
- Bolt or nail together wood or steel framework to erect derricks.
- Supply equipment to rig floors as requested and provide assistance to roughnecks.
- Clean up spilled oil by bailing it into barrels.
- Keep pipe deck and main deck areas clean and tidy.
- Dig drainage ditches around wells and storage tanks.
- Cut down and remove trees and brush to clear drill sites, to reduce fire hazards, and to make way for roads to sites.
- Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.
- Mix sealing compounds by hand or with portable electric mixers.
- Spread sealing compound between boards or panels or over cracks, holes, nail heads, or screw heads, using trowels, broadknives, or spatulas.
- Press paper tape over joints to embed tape into sealing compound and to seal joints.
- Apply additional coats to fill in holes and make surfaces smooth.
- Seal joints between plasterboard or other wallboard to prepare wall surfaces for painting or papering.
- Spread and smooth cementing material over tape, using trowels or floating machines to blend joints with wall surfaces.
- Sand or patch nicks or cracks in plasterboard or wallboard.
- Work on high ceilings, using scaffolding or other tools, such as stilts.
- Select the correct sealing compound or tape.
- Countersink nails or screws below surfaces of walls before applying sealing compounds, using hammers or screwdrivers.
- Remove extra compound after surfaces have been covered sufficiently.
- Install metal molding at wall corners to secure wallboard.
- Apply texturizing compounds or primers to walls or ceilings before final finishing, using trowels, brushes, rollers, or spray guns.
- Check adhesives to ensure that they will work and will remain durable.
- Sand rough spots of dried cement between applications of compounds.
- Use mechanical applicators that spread compounds and embed tape in one operation.
- Mix sealing compounds by hand or with portable electric mixers.
- Locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments.
- Attach rigging and signal crane or hoist operators to lift heavy frame and plate sections or other parts into place.
- Study blueprints to determine locations, relationships, or dimensions of parts.
- Repair or replace defective pressure vessel parts, such as safety valves or regulators, using torches, jacks, caulking hammers, power saws, threading dies, welding equipment, or metalworking machinery.
- Bolt or arc weld pressure vessel structures and parts together, using wrenches or welding equipment.
- Position, align, and secure structural parts or related assemblies to boiler frames, tanks, or vats of pressure vessels, following blueprints.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Shape or fabricate parts, such as stacks, uptakes, or chutes, to adapt pressure vessels, heat exchangers, or piping to premises, using heavy-metalworking machines such as brakes, rolls, or drill presses.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Lay out plate, sheet steel, or other heavy metal and locate and mark bending and cutting lines, using protractors, compasses, and drawing instruments or templates.
- Examine boilers, pressure vessels, tanks, or vats to locate defects, such as leaks, weak spots, or defective sections, so that they can be repaired.
- Shape seams, joints, or irregular edges of pressure vessel sections or structural parts to attain specified fit of parts, using cutting torches, hammers, files, or metalworking machines.
- Inspect assembled vessels or individual components, such as tubes, fittings, valves, controls, or auxiliary mechanisms, to locate any defects.
- Straighten or reshape bent pressure vessel plates or structure parts, using hammers, jacks, or torches.
- Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.
- Clean pressure vessel equipment, using scrapers, wire brushes, and cleaning solvents.
- Bell, bead with power hammers, or weld pressure vessel tube ends to ensure leakproof joints.
- Locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments.
- Mix mortar or grout and pour or spread mortar or grout on marble slabs, stone, or foundation.
- Lay out wall patterns or foundations, using straight edge, rule, or staked lines.
- Shape, trim, face and cut marble or stone preparatory to setting, using power saws, cutting equipment, and hand tools.
- Set vertical and horizontal alignment of structures, using plumb bob, gauge line, and level.
- Remove wedges, fill joints between stones, finish joints between stones, using a trowel, and smooth the mortar to an attractive finish, using a tuck pointer.
- Set stone or marble in place, according to layout or pattern.
- Clean excess mortar or grout from surface of marble, stone, or monument, using sponge, brush, water, or acid.
- Lay brick to build shells of chimneys and smokestacks or to line or reline industrial furnaces, kilns, boilers and similar installations.
- Replace broken or missing masonry units in walls or floors.
- Smooth, polish, and bevel surfaces, using hand tools and power tools.
- Drill holes in marble or ornamental stone and anchor brackets in holes.
- Repair cracked or chipped areas of stone or marble, using blowtorch and mastic, and remove rough or defective spots from concrete, using power grinder or chisel and hammer.
- Remove sections of monument from truck bed, and guide stone onto foundation, using skids, hoist, or truck crane.
- Construct and install prefabricated masonry units.
- Dig trench for foundation of monument, using pick and shovel.
- Position mold along guidelines of wall, press mold in place, and remove mold and paper from wall.
- Line interiors of molds with treated paper and fill molds with composition-stone mixture.
- Mix mortar or grout and pour or spread mortar or grout on marble slabs, stone, or foundation.
- Perform tie spacing layout and measure, mark, drill or cut.
- Clean work areas, machines, or equipment, to maintain a clean and safe job site.
- Fasten timbers or lumber with glue, screws, pegs, or nails and install hardware.
- Select tools, equipment, or materials from storage and transport items to work site.
- Drill holes in timbers or lumber.
- Cut timbers, lumber, or paneling to specified dimensions.
- Position and hold timbers, lumber, or paneling in place for fastening or cutting.
- Align, straighten, plumb, or square forms for installation.
- Hold plumb bobs, sighting rods, or other equipment to aid in establishing reference points and lines.
- Erect scaffolding, shoring, or braces.
- Construct forms and assist in raising them to the required elevation.
- Install handrails under the direction of a carpenter.
- Glue and clamp edges or joints of assembled parts.
- Smooth or sand surfaces to remove ridges, tool marks, glue, or caulking.
- Secure stakes to grids for constructions of footings, nail scabs to footing forms, and vibrate and float concrete.
- Cut and install insulating or sound-absorbing material.
- Cut tile or linoleum to fit and spread adhesives on flooring for installation.
- Cover surfaces with laminated plastic covering material.
- Perform tie spacing layout and measure, mark, drill or cut.
- Chop tar into small pieces, and heat chopped tar in kettles.
- Check to ensure that completed roofs are watertight.
- Sweep and clean roofs to prepare them for the application of new roofing materials.
- Locate worn or torn areas in roofs.
- Clean work areas and equipment.
- Maintain tools and equipment.
- Cover roofs with layers of roofing felt or asphalt strips before installing tile, slate, or composition materials.
- Remove old roofing materials.
- Unload materials and tools from work trucks, and unroll roofing as directed.
- Set ladders, scaffolds, and hoists in place for taking supplies to roofs.
- Place tiles, nail them to roof boards, and cover nailheads with roofing cement.
- Provide assistance to skilled roofers installing and repairing roofs, flashings, and surfaces.
- Attach roofing paper and composition shingles, using nails.
- Perform emergency leak repairs and general maintenance for a variety of roof types.
- Attach sheets of metal to roof boards or building frameworks when installing metal roofs.
- Hoist tar and roofing materials to roofs, using ropes and pulleys, or carry materials up ladders.
- Apply shingles, gravel, or asphalt over the top layer of tar to protect the roofing material.
- Clear drains and downspouts and clean gutters.
- Chop tar into small pieces, and heat chopped tar in kettles.
- Blend compounds to form adhesive mixtures used for marker installation.
- Set out signs and cones around work areas to divert traffic.
- Flag motorists to warn them of obstacles or repair work ahead.
- Perform preventative maintenance on vehicles and heavy equipment.
- Drive trucks to transport crews and equipment to work sites.
- Erect, install, or repair guardrails, road shoulders, berms, highway markers, warning signals, and highway lighting, using hand tools and power tools.
- Clean and clear debris from culverts, catch basins, drop inlets, ditches, and other drain structures.
- Drive heavy equipment and vehicles with adjustable attachments to sweep debris from paved surfaces, mow grass and weeds, remove snow and ice, and spread salt and sand.
- Haul and spread sand, gravel, and clay to fill washouts and repair road shoulders.
- Inspect, clean, and repair drainage systems, bridges, tunnels, and other structures.
- Remove litter and debris from roadways, including debris from rock and mud slides.
- Dump, spread, and tamp asphalt, using pneumatic tampers, to repair joints and patch broken pavement.
- Perform roadside landscaping work, such as clearing weeds and brush, and planting and trimming trees.
- Apply poisons along roadsides and in animal burrows to eliminate unwanted roadside vegetation and rodents.
- Measure and mark locations for installation of markers, using tape, string, or chalk.
- Paint traffic control lines and place pavement traffic messages, by hand or using machines.
- Apply oil to road surfaces, using sprayers.
- Inspect markers to verify accurate installation.
- Place and remove snow fences used to prevent the accumulation of drifting snow on highways.
- Blend compounds to form adhesive mixtures used for marker installation.
- Mix and match colors of paint, stain, or varnish with oil or thinning and drying additives to obtain desired colors and consistencies.
- Fill cracks, holes, or joints with caulk, putty, plaster, or other fillers, using caulking guns or putty knives.
- Cover surfaces with dropcloths or masking tape and paper to protect surfaces during painting.
- Smooth surfaces, using sandpaper, scrapers, brushes, steel wool, or sanding machines.
- Read work orders or receive instructions from supervisors or homeowners to determine work requirements.
- Apply primers or sealers to prepare new surfaces, such as bare wood or metal, for finish coats.
- Apply paint, stain, varnish, enamel, or other finishes to equipment, buildings, bridges, or other structures, using brushes, spray guns, or rollers.
- Erect scaffolding or swing gates, or set up ladders, to work above ground level.
- Calculate amounts of required materials and estimate costs, based on surface measurements or work orders.
- Polish final coats to specified finishes.
- Wash and treat surfaces with oil, turpentine, mildew remover, or other preparations, and sand rough spots to ensure that finishes will adhere properly.
- Select and purchase tools or finishes for surfaces to be covered, considering durability, ease of handling, methods of application, and customers' wishes.
- Remove old finishes by stripping, sanding, wire brushing, burning, or using water or abrasive blasting.
- Remove fixtures such as pictures, door knobs, lamps, or electric switch covers prior to painting.
- Use special finishing techniques such as sponging, ragging, layering, or faux finishing.
- Cut stencils and brush or spray lettering or decorations on surfaces.
- Waterproof buildings, using waterproofers or caulking.
- Spray or brush hot plastics or pitch onto surfaces.
- Bake finishes on painted or enameled articles, using baking ovens.
- Mix and match colors of paint, stain, or varnish with oil or thinning and drying additives to obtain desired colors and consistencies.
- Mix and pour concrete around bases of posts, or tamp soil into postholes to embed posts.
- Establish the location for a fence, and gather information needed to ensure that there are no electric cables or water lines in the area.
- Set metal or wooden posts in upright positions in postholes.
- Measure and lay out fence lines and mark posthole positions, following instructions, drawings, or specifications.
- Align posts, by lines or sighting, and verify vertical alignment of posts, using plumb bobs or spirit levels.
- Attach rails or tension wire along bottoms of posts to form fencing frames.
- Dig postholes, using spades, posthole diggers, or power-driven augers.
- Attach fence rail supports to posts, using hammers and pliers.
- Assemble gates, and fasten gates into position, using hand tools.
- Make rails for fences, by sawing lumber or by cutting metal tubing to required lengths.
- Nail top and bottom rails to fence posts, or insert them in slots on posts.
- Discuss fencing needs with customers, and estimate and quote prices.
- Stretch wire, wire mesh, or chain link fencing between posts, and attach fencing to frames.
- Complete top fence rails of metal fences by connecting tube sections, using metal sleeves.
- Erect alternate panel, basket weave, and louvered fences.
- Insert metal tubing through rail supports.
- Nail pointed slats to rails to construct picket fences.
- Construct and repair barriers, retaining walls, trellises, and other types of fences, walls, and gates.
- Weld metal parts together, using portable gas welding equipment.
- Blast rock formations and rocky areas with dynamite to facilitate posthole digging.
- Mix and pour concrete around bases of posts, or tamp soil into postholes to embed posts.
- Mix cleaning solutions, abrasive compositions, or other compounds, according to formulas.
- Rinse objects and place them on drying racks or use cloth, squeegees, or air compressors to dry surfaces.
- Apply paints, dyes, polishes, reconditioners, waxes, or masking materials to vehicles to preserve, protect, or restore color or condition.
- Clean and polish vehicle windows.
- Drive vehicles to or from workshops or customers' workplaces or homes.
- Scrub, scrape, or spray machine parts, equipment, or vehicles, using scrapers, brushes, clothes, cleaners, disinfectants, insecticides, acid, abrasives, vacuums, or hoses.
- Inspect parts, equipment, or vehicles for cleanliness, damage, and compliance with standards or regulations.
- Maintain inventories of supplies.
- Pre-soak or rinse machine parts, equipment, or vehicles by immersing objects in cleaning solutions or water, manually or using hoists.
- Turn valves or disconnect hoses to eliminate water, cleaning solutions, or vapors from machinery or tanks.
- Turn valves or handles on equipment to regulate pressure or flow of water, air, steam, or abrasives from sprayer nozzles.
- Sweep, shovel, or vacuum loose debris or salvageable scrap into containers and remove containers from work areas.
- Monitor operation of cleaning machines and stop machines or notify supervisors when malfunctions occur.
- Press buttons to activate cleaning equipment or machines.
- Connect hoses or lines to pumps or other equipment.
- Collect and test samples of cleaning solutions or vapors.
- Clean the plastic work inside cars, using paintbrushes.
- Disassemble and reassemble machines or equipment or remove and reattach vehicle parts or trim, using hand tools.
- Lubricate machinery, vehicles, or equipment or perform minor repairs or adjustments, using hand tools.
- Transport materials, equipment, or supplies to or from work areas, using carts or hoists.
- Fit boot spoilers, side skirts, or mud flaps to cars.
- Mix cleaning solutions, abrasive compositions, or other compounds, according to formulas.
- Mix or pour concrete into forms to encase waste material for disposal.
- Build containment areas prior to beginning abatement or decontamination work.
- Remove asbestos or lead from surfaces, using hand or power tools such as scrapers, vacuums, or high-pressure sprayers.
- Identify asbestos, lead, or other hazardous materials to be removed, using monitoring devices.
- Prepare hazardous material for removal or storage.
- Comply with prescribed safety procedures or federal laws regulating waste disposal methods.
- Load or unload materials into containers or onto trucks, using hoists or forklifts.
- Clean contaminated equipment or areas for reuse, using detergents or solvents, sandblasters, filter pumps, or steam cleaners.
- Remove or limit contamination following emergencies involving hazardous substances.
- Clean mold-contaminated sites by removing damaged porous materials or thoroughly cleaning all contaminated nonporous materials.
- Operate machines or equipment to remove, package, store, or transport loads of waste materials.
- Record numbers of containers stored at disposal sites, specifying amounts or types of equipment or waste disposed.
- Sort specialized hazardous waste at landfills or disposal centers, following proper disposal procedures.
- Operate cranes to move or load baskets, casks, or canisters.
- Drive trucks or other heavy equipment to convey contaminated waste to designated sea or ground locations.
- Identify or separate waste products or materials for recycling or reuse.
- Upload baskets of irradiated elements onto machines that insert fuel elements into canisters and secure lids.
- Process e-waste, such as computer components containing lead or mercury.
- Organize or track the locations of hazardous items in landfills.
- Apply bioremediation techniques to hazardous wastes to allow naturally occurring bacteria to break down toxic substances.
- Package, store, or move irradiated fuel elements in the underwater storage basins of nuclear reactor plants, using machines or equipment.
- Mix or pour concrete into forms to encase waste material for disposal.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Maintain equipment, making repairs or modifications when necessary.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Transport prefabricated parts to construction sites for assembly and installation.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Hire, train, or supervise new employees or apprentices.
- Fabricate or alter parts at construction sites, using shears, hammers, punches, or drills.
- Determine project requirements, such as scope, assembly sequences, or required methods or materials, using blueprints, drawings, or written or verbal instructions.
- Maneuver completed roofing units into position for installation.
- Select gauges or types of sheet metal or nonmetallic material, according to product specifications.
- Shape metal material over anvils, blocks, or other forms, using hand tools.
- Trim, file, grind, deburr, buff, or smooth surfaces, seams, or joints of assembled parts, using hand tools or portable power tools.
- Inspect individual parts, assemblies, or installations, using measuring instruments, such as calipers, scales, or micrometers.
- Develop or lay out patterns, using computerized metalworking equipment.
- Convert blueprints into shop drawings to be followed in the construction or assembly of sheet metal products.
- Perform sheet metal work necessary for solar panel installations.
- Verify that heating, ventilating, and air conditioning (HVAC) systems are designed, installed, and calibrated in accordance with green certification standards, such as those of Leadership in Energy and Environmental Design (LEED).
- Secure metal roof panels in place by interlocking and fastening grooved panel edges.
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Finish parts, using hacksaws or hand, rotary, or squaring shears.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Measure, cut, and bend wire and conduit, using measuring instruments and hand tools.
- Strip insulation from wire ends, using wire stripping pliers, and attach wires to terminals for subsequent soldering.
- Trace out short circuits in wiring, using test meter.
- Examine electrical units for loose connections and broken insulation and tighten connections, using hand tools.
- Maintain tools, vehicles, and equipment and keep parts and supplies in order.
- Drill holes and pull or push wiring through openings, using hand and power tools.
- Clean work area and wash parts.
- Perform semi-skilled and unskilled laboring duties related to the installation, maintenance and repair of a wide variety of electrical systems and equipment.
- Thread conduit ends, connect couplings, and fabricate and secure conduit support brackets, using hand tools.
- Disassemble defective electrical equipment, replace defective or worn parts, and reassemble equipment, using hand tools.
- Construct controllers and panels, using power drills, drill presses, taps, saws, and punches.
- Transport tools, materials, equipment, and supplies to work site by hand, handtruck, or heavy, motorized truck.
- String transmission lines or cables through ducts or conduits, under the ground, through equipment, or to towers.
- Install copper-clad ground rods, using a manual post driver.
- Dig trenches or holes for installation of conduit or supports.
- Raise, lower, or position equipment, tools, and materials, using hoist, hand line, or block and tackle.
- Bolt component parts together to form tower assemblies, using hand tools.
- Erect electrical system components and barricades, and rig scaffolds, hoists, and shoring.
- Trim trees and clear undergrowth along right-of-way.
- Requisition materials, using warehouse requisition or release forms.
- Solder electrical connections, using soldering iron.
- Paint a variety of objects related to electrical functions.
- Break up concrete, using airhammer, to facilitate installation, construction, or repair of equipment.
- Operate heavy equipment, such as backhoes.
- Operate cutting torches and welding equipment, while working with conduit and metal components to construct devices associated with electrical functions.
- Measure, cut, and bend wire and conduit, using measuring instruments and hand tools.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Check the forms that hold the concrete to see that they are properly constructed.
- Set the forms that hold concrete to the desired pitch and depth, and align them.
- Spread, level, and smooth concrete, using rake, shovel, hand or power trowel, hand or power screed, and float.
- Monitor how the wind, heat, or cold affect the curing of the concrete throughout the entire process.
- Mold expansion joints and edges, using edging tools, jointers, and straightedge.
- Signal truck driver to position truck to facilitate pouring concrete, and move chute to direct concrete on forms.
- Direct the casting of the concrete and supervise laborers who use shovels or special tools to spread it.
- Produce rough concrete surface, using broom.
- Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.
- Operate power vibrator to compact concrete.
- Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.
- Waterproof or restore concrete surfaces, using appropriate compounds.
- Chip, scrape, and grind high spots, ridges, and rough projections to finish concrete, using pneumatic chisels, power grinders, or hand tools.
- Cut out damaged areas, drill holes for reinforcing rods, and position reinforcing rods to repair concrete, using power saw and drill.
- Wet concrete surface, and rub with stone to smooth surface and obtain specified finish.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Build wooden molds, and clamp molds around area to be repaired, using hand tools.
- Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.
- Fabricate concrete beams, columns, and panels.
- Polish surface, using polishing or surfacing machine.
- Cut metal division strips, and press them into terrazzo base so that top edges form desired design or pattern.
- Push roller over surface to embed chips in surface.
- Apply muriatic acid to clean surface, and rinse with water.
- Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Locate and mark the position of pipe installations, connections, passage holes, or fixtures in structures, using measuring instruments such as rulers or levels.
- Shut off steam, water, or other gases or liquids from pipe sections, using valve keys or wrenches.
- Install underground storm, sanitary, or water piping systems, extending piping as needed to connect fixtures and plumbing.
- Assemble pipe sections, tubing, or fittings, using couplings, clamps, screws, bolts, cement, plastic solvent, caulking, or soldering, brazing, or welding equipment.
- Cut, thread, or hammer pipes to specifications, using tools such as saws, cutting torches, pipe threaders, or pipe benders.
- Lay out full scale drawings of pipe systems, supports, or related equipment, according to blueprints.
- Plan pipe system layout, installation, or repair, according to specifications.
- Review blueprints, building codes, or specifications to determine work details or procedures.
- Select pipe sizes, types, or related materials, such as supports, hangers, or hydraulic cylinders, according to specifications.
- Fill pipes or plumbing fixtures with water or air and observe pressure gauges to detect and locate leaks.
- Direct helpers engaged in pipe cutting, preassembly, or installation of plumbing systems or components.
- Inspect, examine, or test installed systems or pipe lines, using pressure gauge, hydrostatic testing, observation, or other methods.
- Install pipe assemblies, fittings, valves, appliances such as dishwashers or water heaters, or fixtures such as sinks or toilets, using hand or power tools.
- Anchor steel supports from ceiling joists to hold pipes in place.
- Attach pipes to walls, structures, or fixtures, such as radiators or tanks, using brackets, clamps, tools, or welding equipment.
- Modify, clean, or maintain pipe systems, units, fittings, or related machines or equipment, using hand or power tools.
- Install automatic controls to regulate pipe systems.
- Estimate time, material, or labor costs for use in project plans.
- Keep records of work assignments.
- Inspect structures to assess material or equipment needs, to establish the sequence of pipe installations, or to plan installation around obstructions, such as electrical wiring.
- Maintain or repair plumbing by replacing defective washers, replacing or mending broken pipes, or opening clogged drains.
- Repair or remove and replace system components.
- Cut openings in structures to accommodate pipes or pipe fittings, using hand or power tools.
- Install green plumbing equipment, such as faucet flow restrictors, dual-flush or pressure-assisted flush toilets, or tankless hot water heaters.
- Inspect work sites for obstructions or holes that could cause structural weakness.
- Install pipe systems to support alternative energy-fueled systems, such as geothermal heating or cooling systems.
- Install fixtures, appliances, or equipment designed to reduce water or energy consumption.
- Repair hydraulic or air pumps.
- Weld small pipes or special piping, using specialized techniques, equipment, or materials, such as computer-assisted welding or microchip fabrication.
- Operate motorized pumps to remove water from flooded manholes, basements, or facility floors.
- Locate and mark the position of pipe installations, connections, passage holes, or fixtures in structures, using measuring instruments such as rulers or levels.
