- Design equipment configurations to meet personnel needs.
Occupations with related tasks Save Table: XLSX CSV
- Create and lay out designs for drill and blast patterns.
- Design well pumping systems.
- Operate controls to stabilize machines and to position and align drills.
- Start, stop, and control drilling speed of machines and insertion of casings into holes.
- Regulate air pressure, rotary speed, and downward pressure, according to the type of rock or concrete being drilled.
- Select and attach drill bits and drill rods, adding more rods as hole depths increase, and changing drill bits as needed.
- Drive or guide truck-mounted equipment into position, level and stabilize rigs, and extend telescoping derricks.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Verify depths and alignments of boring positions.
- Perform routine maintenance and upgrade work on machines and equipment, such as replacing parts, building up drill bits, and lubricating machinery.
- Select the appropriate drill for the job, using knowledge of rock or soil conditions.
- Document geological formations encountered during work.
- Drive trucks, tractors, or truck-mounted drills to and from work sites.
- Assemble and position machines, augers, casing pipes, and other equipment, using hand and power tools.
- Record drilling progress and geological data.
- Retrieve lost equipment from bore holes, using retrieval tools and equipment.
- Fabricate well casings.
- Pour water into wells, or pump water or slush into wells to cool drill bits and to remove drillings.
- Place and install screens, casings, pumps, and other well fixtures to develop wells.
- Operate water-well drilling rigs and other equipment to drill, bore, and dig for water wells or for environmental assessment purposes.
- Review client requirements and proposed locations for drilling operations to determine feasibility, and to determine cost estimates.
- Drill or bore holes in rock for blasting, grouting, anchoring, or building foundations.
- Perform pumping tests to assess well performance.
- Disinfect, reconstruct, and redevelop contaminated wells and water pumping systems, and clean and disinfect new wells in preparation for use.
- Signal crane operators to move equipment.
- Withdraw drill rods from holes, and extract core samples.
- Inspect core samples to determine nature of strata, or take samples to laboratories for analysis.
- Retract augers to force discharge dirt from holes.
- Observe electronic graph recorders and flow meters that monitor the water used to flush debris from holes.
- Monitor drilling operations, by checking gauges and listening to equipment to assess drilling conditions and to determine the need to adjust drilling or alter equipment.
- Create and lay out designs for drill and blast patterns.
- Design well pumping systems.
- Operate computer-aided drafting and design applications to design avionics system modifications.
- Test and troubleshoot instruments, components, and assemblies, using circuit testers, oscilloscopes, or voltmeters.
- Keep records of maintenance and repair work.
- Adjust, repair, or replace malfunctioning components or assemblies, using hand tools or soldering irons.
- Install electrical and electronic components, assemblies, and systems in aircraft, using hand tools, power tools, or soldering irons.
- Set up and operate ground support and test equipment to perform functional flight tests of electrical and electronic systems.
- Assemble components such as switches, electrical controls, and junction boxes, using hand tools or soldering irons.
- Lay out installation of aircraft assemblies and systems, following documentation such as blueprints, manuals, and wiring diagrams.
- Connect components to assemblies such as radio systems, instruments, magnetos, inverters, and in-flight refueling systems, using hand tools and soldering irons.
- Interpret flight test data to diagnose malfunctions and systemic performance problems.
- Coordinate work with that of engineers, technicians, and other aircraft maintenance personnel.
- Fabricate parts and test aids as required.
- Assemble prototypes or models of circuits, instruments, and systems for use in testing.
- Operate computer-aided drafting and design applications to design avionics system modifications.
- Develop or modify industrial electronic devices, circuits, or equipment, according to available specifications.
- Test faulty equipment to diagnose malfunctions, using test equipment or software, and applying knowledge of the functional operation of electronic units and systems.
- Maintain equipment logs that record performance problems, repairs, calibrations, or tests.
- Set up and test industrial equipment to ensure that it functions properly.
- Inspect components of industrial equipment for accurate assembly and installation or for defects, such as loose connections or frayed wires.
- Install repaired equipment in various settings, such as industrial or military establishments.
- Operate equipment to demonstrate proper use or to analyze malfunctions.
- Enter information into computer to copy program or to draw, modify, or store schematics, applying knowledge of software package used.
- Perform scheduled preventive maintenance tasks, such as checking, cleaning, or repairing equipment, to detect and prevent problems.
- Calibrate testing instruments and installed or repaired equipment to prescribed specifications.
- Repair or adjust equipment, machines, or defective components, replacing worn parts, such as gaskets or seals in watertight electrical equipment.
- Consult with customers, supervisors, or engineers to plan layout of equipment or to resolve problems in system operation or maintenance.
- Maintain inventory of spare parts.
- Study blueprints, schematics, manuals, or other specifications to determine installation procedures.
- Examine work orders and converse with equipment operators to detect equipment problems and to ascertain whether mechanical or human errors contributed to the problems.
- Coordinate efforts with other workers involved in installing or maintaining equipment or components.
- Determine feasibility of using standardized equipment or develop specifications for equipment required to perform additional functions.
- Advise management regarding customer satisfaction, product performance, or suggestions for product improvements.
- Send defective units to the manufacturer or to a specialized repair shop for repair.
- Sign overhaul documents for equipment replaced or repaired.
- Develop or modify industrial electronic devices, circuits, or equipment, according to available specifications.
- Design and lay out geothermal heat systems according to property characteristics, heating and cooling requirements, piping and equipment requirements, applicable regulations, or other factors.
- Monitor and adjust operations of geothermal power plant equipment or systems.
- Prepare and maintain logs, reports, or other documentation of work performed.
- Identify and correct malfunctions of geothermal plant equipment, electrical systems, instrumentation, or controls.
- Collect and record data associated with operating geothermal power plants or well fields.
- Determine whether emergency or auxiliary systems will be needed to keep properties heated or cooled in extreme weather conditions.
- Perform pre- and post-installation pressure, flow, and related tests of vertical and horizontal geothermal loop piping.
- Identify equipment options, such as compressors, and make appropriate selections.
- Adjust power production systems to meet load and distribution demands.
- Maintain electrical switchgear, process controls, transmitters, gauges, and control equipment in accordance with geothermal plant procedures.
- Calculate heat loss and heat gain factors for residential properties to determine heating and cooling required by installed geothermal systems.
- Maintain, calibrate, or repair plant instrumentation, control, and electronic devices in geothermal plants.
- Install and maintain geothermal plant electrical protection equipment.
- Install and maintain geothermal system instrumentation or controls.
- Prepare newly installed geothermal heat systems for operation by flushing, purging, or other actions.
- Weld piping, such as high density polyethylene (HDPE) piping, using techniques such as butt, socket, side-wall, and electro-fusion welding.
- Test water sources for factors, such as flow volume and contaminant presence.
- Install, maintain, or repair ground or water source-coupled heat pumps to heat and cool residential or commercial building air or water.
- Integrate hot water heater systems with geothermal heat exchange systems.
- Determine the type of geothermal loop system most suitable to a specific property and its heating and cooling needs.
- Dig trenches for system piping to appropriate depths and lay piping in trenches.
- Apply coatings or operate systems to mitigate corrosion of geothermal plant equipment or structures.
- Backfill piping trenches to protect pipes from damage.
- Operate equipment, such as excavators, backhoes, rock hammers, trench compactors, pavement saws, grout mixers or pumps, geothermal loop reels, and coil tubing units (CTU).
- Design and lay out geothermal heat systems according to property characteristics, heating and cooling requirements, piping and equipment requirements, applicable regulations, or other factors.
- Create and lay out designs for drill and blast patterns.
- Examine blast areas to determine amounts and kinds of explosive charges needed and to ensure that safety laws are observed.
- Tie specified lengths of delaying fuses into patterns in order to time sequences of explosions.
- Place safety cones around blast areas to alert other workers of danger zones, and signal workers as necessary to ensure that they clear blast sites prior to explosions.
- Place explosive charges in holes or other spots; then detonate explosives to demolish structures or to loosen, remove, or displace earth, rock, or other materials.
- Insert, pack, and pour explosives, such as dynamite, ammonium nitrate, black powder, or slurries into blast holes; then shovel drill cuttings, admit water into boreholes, and tamp material to compact charges.
- Mark patterns, locations, and depths of charge holes for drilling, and issue drilling instructions.
- Compile and keep gun and explosives records in compliance with local and federal laws.
- Measure depths of drilled blast holes, using weighted tape measures.
- Connect electrical wire to primers, and cover charges or fill blast holes with clay, drill chips, sand, or other material.
- Lay primacord between rows of charged blast holes, and tie cord into main lines to form blast patterns.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Verify detonation of charges by observing control panels, or by listening for the sounds of blasts.
- Move and store inventories of explosives, loaded perforating guns, and other materials, according to established safety procedures.
- Light fuses, drop detonating devices into wells or boreholes, or activate firing devices with plungers, dials, or buttons, in order to set off single or multiple blasts.
- Drive trucks to transport explosives and blasting equipment to blasting sites.
- Cut specified lengths of primacord and attach primers to cord ends.
- Maintain inventory levels, ordering new supplies as necessary.
- Repair and service blasting, shooting, and automotive equipment, and electrical wiring and instruments, using hand tools.
- Set up and operate short-wave radio or field telephone equipment to transmit and receive blast information.
- Insert waterproof sealers, bullets, and/or powder charges into guns, and screw gun ports back into place.
- Clean, gauge, and lubricate gun ports.
- Connect gun chambers to electric detonating devices, and operate controls at panelboards, in order to detonate charges in guns or to ignite chemical charges.
- Lower perforating guns into wells, using hoists; then use measuring devices and instrument panels to position guns in correct positions for taking samples.
- Insert powder charges into chambers of sidewall sample-taking cylinders, and assemble cylinders, using special wrenches.
- Obtain samples of earth from sidewalls of well boreholes, using electrically exploding devices.
- Document geological formations encountered during work.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Set up and operate equipment such as hoists, jackhammers, and drills, in order to bore charge holes.
- Signal crane operators to move equipment.
- Create and lay out designs for drill and blast patterns.
- Design new equipment to aid in the repair or maintenance of machines, mechanical equipment, or building structures.
- Perform routine maintenance, such as inspecting drives, motors, or belts, checking fluid levels, replacing filters, or doing other preventive maintenance actions.
- Inspect, operate, or test machinery or equipment to diagnose machine malfunctions.
- Adjust functional parts of devices or control instruments, using hand tools, levels, plumb bobs, or straightedges.
- Order parts, supplies, or equipment from catalogs or suppliers.
- Diagnose mechanical problems and determine how to correct them, checking blueprints, repair manuals, or parts catalogs, as necessary.
- Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.
- Clean or lubricate shafts, bearings, gears, or other parts of machinery.
- Estimate costs to repair machinery, equipment, or building structures.
- Align and balance new equipment after installation.
- Record type and cost of maintenance or repair work.
- Maintain or repair specialized equipment or machinery located in cafeterias, laundries, hospitals, stores, offices, or factories.
- Dismantle machines, equipment, or devices to access and remove defective parts, using hoists, cranes, hand tools, or power tools.
- Plan and lay out repair work, using diagrams, drawings, blueprints, maintenance manuals, or schematic diagrams.
- Install equipment to improve the energy or operational efficiency of residential or commercial buildings.
- Set up and operate machine tools to repair or fabricate machine parts, jigs, fixtures, or tools.
- Perform general cleaning of buildings or properties.
- Train or manage maintenance personnel or subcontractors.
- Fabricate or repair counters, benches, partitions, or other wooden structures, such as sheds or outbuildings.
- Paint or repair roofs, windows, doors, floors, woodwork, plaster, drywall, or other parts of building structures.
- Perform routine maintenance on boilers, such as replacing burners or hoses, installing replacement parts, or reinforcing structural weaknesses to ensure optimal boiler efficiency.
- Test and treat water supply.
- Provide groundskeeping services, such as landscaping or snow removal.
- Operate cutting torches or welding equipment to cut or join metal parts.
- Inspect used parts to determine changes in dimensional requirements, using rules, calipers, micrometers, or other measuring instruments.
- Assemble boilers at installation sites, using tools such as levels, plumb bobs, hammers, torches, or other hand tools.
- Lay brick to repair or maintain buildings, walls, arches, or other structures.
- Position, attach, or blow insulating materials to prevent energy losses from buildings, pipes, or other structures or objects.
- Grind and reseat valves, using valve-grinding machines.
- Repair machines, equipment, or structures, using tools such as hammers, hoists, saws, drills, wrenches, or equipment such as precision measuring instruments or electrical or electronic testing devices.
- Design new equipment to aid in the repair or maintenance of machines, mechanical equipment, or building structures.
