- Remove damaged exterior panels, and repair and replace structural frame members.
Occupations with related tasks Save Table: XLSX CSV
- Remove locomotives, car mechanical units, or other components, using pneumatic hoists and jacks, pinch bars, hand tools, and cutting torches.
- Repair, fabricate, and install steel or wood fittings, using blueprints, shop sketches, and instruction manuals.
- Examine car roofs for wear and damage, and repair defective sections, using roofing material, cement, nails, and waterproof paint.
- Repair window sash frames, attach weather stripping and channels to frames, and replace window glass, using hand tools.
- Repair car upholstery.
- Disassemble units such as water pumps, control valves, and compressors so that repairs can be made.
- Record conditions of cars, and repair and maintenance work performed or to be performed.
- Inspect components such as bearings, seals, gaskets, wheels, and coupler assemblies to determine if repairs are needed.
- Repair or replace defective or worn parts such as bearings, pistons, and gears, using hand tools, torque wrenches, power tools, and welding equipment.
- Inspect the interior and exterior of rail cars coming into rail yards to identify defects and to determine the extent of wear and damage.
- Test units for operability before and after repairs.
- Adjust repaired or replaced units as needed to ensure proper operation.
- Perform scheduled maintenance, and clean units and components.
- Paint car exteriors, interiors, and fixtures.
- Repair and maintain electrical and electronic controls for propulsion and braking systems.
- Measure diameters of axle wheel seats, using micrometers, and mark dimensions on axles so that wheels can be bored to specified dimensions.
- Test electrical systems of cars by operating systems and using testing equipment such as ammeters.
- Replace defective wiring and insulation, and tighten electrical connections, using hand tools.
- Install and repair interior flooring, fixtures, walls, plumbing, steps, and platforms.
- Align car sides for installation of car ends and crossties, using width gauges, turnbuckles, and wrenches.
- Remove locomotives, car mechanical units, or other components, using pneumatic hoists and jacks, pinch bars, hand tools, and cutting torches.
- Repair, fabricate, and install steel or wood fittings, using blueprints, shop sketches, and instruction manuals.
- Examine car roofs for wear and damage, and repair defective sections, using roofing material, cement, nails, and waterproof paint.
- Repair window sash frames, attach weather stripping and channels to frames, and replace window glass, using hand tools.
- Repair car upholstery.
- Disassemble units such as water pumps, control valves, and compressors so that repairs can be made.
- Diagnose and repair vehicle heating and cooling systems.
- Inspect, repair, and maintain automotive and mechanical equipment and machinery, such as pumps and compressors.
- Install or repair accessories.
- Repair or adjust seats, doors, or windows.
- Disassemble and overhaul internal combustion engines, pumps, generators, transmissions, clutches, and differential units.
- Rebuild gas or diesel engines.
- Specialize in repairing and maintaining parts of the engine, such as fuel injection systems.
- Recondition and replace parts, pistons, bearings, gears, and valves.
- Dismount, mount, and repair or replace tires.
- Use handtools, such as screwdrivers, pliers, wrenches, pressure gauges, or precision instruments, as well as power tools, such as pneumatic wrenches, lathes, welding equipment, or jacks and hoists.
- Inspect brake systems, steering mechanisms, wheel bearings, and other important parts to ensure that they are in proper operating condition.
- Raise trucks, buses, and heavy parts or equipment using hydraulic jacks or hoists.
- Adjust and reline brakes, align wheels, tighten bolts and screws, and reassemble equipment.
- Attach test instruments to equipment, and read dials and gauges to diagnose malfunctions.
- Perform routine maintenance such as changing oil, checking batteries, and lubricating equipment and machinery.
- Examine and adjust protective guards, loose bolts, and specified safety devices.
- Inspect, test, and listen to defective equipment to diagnose malfunctions, using test instruments such as handheld computers, motor analyzers, chassis charts, or pressure gauges.
- Rewire ignition systems, lights, and instrument panels.
- Test drive trucks and buses to diagnose malfunctions or to ensure that they are working properly.
- Inspect and verify dimensions and clearances of parts to ensure conformance to factory specifications.
- Adjust or repair computer controlled exhaust emissions devices.
- Align front ends and suspension systems.
- Maintain or repair vehicles with alternative fuel systems, including biodiesel, hybrid, or compressed natural gas vehicles.
- Measure vehicle emissions to determine whether they are within acceptable limits.
- Follow green operational practices involving conservation of water or energy or reduction of solid waste.
- Operate valve-grinding machines to grind and reset valves.
- Diagnose and repair vehicle heating and cooling systems.
- Inspect, repair, and maintain automotive and mechanical equipment and machinery, such as pumps and compressors.
- Install or repair accessories.
- Repair or adjust seats, doors, or windows.
- Disassemble and overhaul internal combustion engines, pumps, generators, transmissions, clutches, and differential units.
- Rebuild gas or diesel engines.
- Specialize in repairing and maintaining parts of the engine, such as fuel injection systems.
- Recondition and replace parts, pistons, bearings, gears, and valves.
- Dismount, mount, and repair or replace tires.
- Repair, reline, replace, and adjust brakes.
- Tear down, repair, and rebuild faulty assemblies, such as power systems, steering systems, and linkages.
- Repair or replace parts such as pistons, rods, gears, valves, and bearings.
- Install, adjust, or repair hydraulic or electromagnetic automatic lift mechanisms used to raise and lower automobile windows, seats, and tops.
- Disassemble units and inspect parts for wear, using micrometers, calipers, and gauges.
- Repair, replace, or adjust defective fuel injectors, carburetor parts, and gasoline filters.
- Rebuild parts, such as crankshafts and cylinder blocks.
- Inspect vehicles for damage and record findings so that necessary repairs can be made.
- Test drive vehicles and test components and systems, using equipment such as infrared engine analyzers, compression gauges, and computerized diagnostic devices.
- Test and adjust repaired systems to meet manufacturers' performance specifications.
- Review work orders and discuss work with supervisors.
- Estimate costs of vehicle repair.
- Confer with customers to obtain descriptions of vehicle problems and to discuss work to be performed and future repair requirements.
- Align vehicles' front ends.
- Align wheels, axles, frames, torsion bars, and steering mechanisms of automobiles, using special alignment equipment and wheel-balancing machines.
- Perform routine and scheduled maintenance services, such as oil changes, lubrications, and tune-ups.
- Plan work procedures, using charts, technical manuals, and experience.
- Follow checklists to ensure all important parts are examined, including belts, hoses, steering systems, spark plugs, brake and fuel systems, wheel bearings, and other potentially troublesome areas.
- Maintain cleanliness of work area.
- Change spark plugs, fuel filters, air filters, and batteries in hybrid electric vehicles.
- Repair and service air conditioning, heating, engine cooling, and electrical systems.
- Test electronic computer components in automobiles to ensure proper operation.
- Overhaul or replace carburetors, blowers, generators, distributors, starters, and pumps.
- Rewire ignition systems, lights, and instrument panels.
- Troubleshoot fuel, ignition, and emissions control systems, using electronic testing equipment.
- Tune automobile engines to ensure proper and efficient functioning.
- Conduct visual inspections of compressed natural gas fuel systems to identify cracks, gouges, abrasions, discoloration, broken fibers, loose brackets, damaged gaskets, or other problems.
- Diagnose and replace or repair engine management systems or related sensors for flexible fuel vehicles (FFVs) with ignition timing, fuel rate, alcohol concentration, or air-to-fuel ratio malfunctions.
- Repair or rebuild transmissions.
- Retrofit vehicle fuel systems with aftermarket products, such as vapor transfer devices, evaporation control devices, swirlers, lean burn devices, and friction reduction devices, to enhance combustion and fuel efficiency.
- Repair, reline, replace, and adjust brakes.
- Tear down, repair, and rebuild faulty assemblies, such as power systems, steering systems, and linkages.
- Repair or replace parts such as pistons, rods, gears, valves, and bearings.
- Install, adjust, or repair hydraulic or electromagnetic automatic lift mechanisms used to raise and lower automobile windows, seats, and tops.
- Disassemble units and inspect parts for wear, using micrometers, calipers, and gauges.
- Repair, replace, or adjust defective fuel injectors, carburetor parts, and gasoline filters.
- Rebuild parts, such as crankshafts and cylinder blocks.
- Replace defective parts, using hand tools, arbor presses, flexible power presses, or power tools.
- Repair or replace other parts, such as headlights, horns, handlebar controls, gasoline or oil tanks, starters, or mufflers.
- Repair or adjust motorcycle subassemblies, such as forks, transmissions, brakes, or drive chains, according to specifications.
- Dismantle engines and repair or replace defective parts, such as magnetos, carburetors, or generators.
- Disassemble subassembly units and examine condition, movement, or alignment of parts, visually or using gauges.
- Mount, balance, change, or check condition or pressure of tires.
- Connect test panels to engines and measure generator output, ignition timing, or other engine performance indicators.
- Listen to engines, examine vehicle frames, or confer with customers to determine nature and extent of malfunction or damage.
- Reassemble frames and reinstall engines after repairs.
- Remove cylinder heads and grind valves to scrape off carbon and replace defective valves, pistons, cylinders, or rings, using hand and power tools.
- Install motorcycle accessories.
- Reassemble and test subassembly units.
- Hammer out dents and bends in frames and weld tears and breaks.
- Replace defective parts, using hand tools, arbor presses, flexible power presses, or power tools.
- Repair or replace other parts, such as headlights, horns, handlebar controls, gasoline or oil tanks, starters, or mufflers.
- Repair or adjust motorcycle subassemblies, such as forks, transmissions, brakes, or drive chains, according to specifications.
- Dismantle engines and repair or replace defective parts, such as magnetos, carburetors, or generators.
- Disassemble subassembly units and examine condition, movement, or alignment of parts, visually or using gauges.
- Install, repair, or replace safety glass and related materials, such as back glass heating elements, on vehicles or equipment.
- Replace or adjust motorized or manual window-raising mechanisms.
- Prime all scratches on pinchwelds with primer and allow to dry.
- Remove all dirt, foreign matter, and loose glass from damaged areas, apply primer along windshield or window edges, and allow primer to dry.
- Allow all glass parts installed with urethane ample time to cure, taking temperature and humidity into account.
- Apply a bead of urethane around the perimeter of each pinchweld and dress the remaining urethane on the pinchwelds so that it is of uniform level and thickness.
- Install replacement glass in vehicles.
- Remove broken or damaged glass windshields or window glass from motor vehicles, using hand tools to remove screws from frames holding glass.
- Remove moldings, clips, windshield wipers, screws, bolts, and inside A-pillar moldings and lower headliners in preparation for installation or repair work.
- Install rubber channeling strips around edges of glass or frames to weatherproof windows or to prevent rattling.
- Select appropriate tools, safety equipment, and parts, according to job requirements.
- Obtain windshields or windows for specific automobile makes and models from stock and examine them for defects prior to installation.
- Check for and remove moisture or contamination in damaged areas and keep areas dry until repairs are complete.
- Replace all moldings, clips, windshield wipers, or other parts that were removed prior to glass replacement or repair.
- Cool or warm glass in the event of temperature extremes.
- Install new foam dams on pinchwelds, if required.
- Hold cut or uneven edges of glass against automated abrasive belts to shape or smooth edges.
- Cut flat safety glass according to specified patterns or perform precision pattern making and glass cutting to custom fit replacement windows.
- Install, repair, or replace safety glass and related materials, such as back glass heating elements, on vehicles or equipment.
- Replace or adjust motorized or manual window-raising mechanisms.
- Prime all scratches on pinchwelds with primer and allow to dry.
- Remove all dirt, foreign matter, and loose glass from damaged areas, apply primer along windshield or window edges, and allow primer to dry.
- Allow all glass parts installed with urethane ample time to cure, taking temperature and humidity into account.
- Apply a bead of urethane around the perimeter of each pinchweld and dress the remaining urethane on the pinchwelds so that it is of uniform level and thickness.
- Install replacement glass in vehicles.
- Remove broken or damaged glass windshields or window glass from motor vehicles, using hand tools to remove screws from frames holding glass.
- Remove moldings, clips, windshield wipers, screws, bolts, and inside A-pillar moldings and lower headliners in preparation for installation or repair work.
- Install rubber channeling strips around edges of glass or frames to weatherproof windows or to prevent rattling.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Record maintenance information, including test results, material usage, and repairs made.
- Lubricate wearing surfaces of mechanical parts, using oils or other lubricants.
- Calibrate instrumentation, such as meters, gauges, and regulators, for pressure, temperature, flow, and level.
- Install, inspect and test electric meters, relays, and power sources to detect causes of malfunctions and inaccuracies, using hand tools and testing equipment.
- Test valves and regulators for leaks and accurate temperature and pressure settings, using precision testing equipment.
- Record meter readings and installation data on meter cards, work orders, or field service orders, or enter data into hand-held computers.
- Turn meters on or off to establish or close service.
- Shut off service and notify repair crews when major repairs are required, such as the replacement of underground pipes or wiring.
- Install regulators and related equipment such as gas meters, odorization units, and gas pressure telemetering equipment.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Turn valves to allow measured amounts of air or gas to pass through meters at specified flow rates.
- Report hazardous field situations and damaged or missing meters.
- Vary air pressure flowing into regulators and turn handles to assess functioning of valves and pistons.
- Examine valves or mechanical control device parts for defects, dents, or loose attachments, and mark malfunctioning areas of defective units.
- Mount and install meters and other electric equipment such as time clocks, transformers, and circuit breakers, using electricians' hand tools.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Investigate instances of illegal tapping into service lines.
- Trace and tag meters or house lines.
- Repair electric meters and components, such as transformers and relays, and replace metering devices, dial glasses, and faulty or incorrect wiring, using hand tools.
- Replace defective parts, such as bellows, range springs, and toggle switches, and reassemble units according to blueprints, using cam presses and hand tools.
- Measure tolerances of assembled and salvageable parts for conformance to standards or specifications, using gauges, micrometers, and calipers.
- Clean internal compartments and moving parts, using rags and cleaning compounds.
- Reassemble repaired equipment, and solder top, front, and back case panels in place, using soldering guns, power tools, and hand tools.
- Attach air hoses to meter inlets, plug outlets, and observe gauges for pressure losses to test internal seams for leaks.
- Make adjustments to meter components, such as setscrews or timing mechanisms, so that they conform to specifications.
- Recommend and write up specifications for changes in hardware, such as house wiring.
- Clamp regulator units into vises on stages above water tanks, and attach compressed air hoses to intake ports.
- Collect money due on delinquent accounts.
- Splice and connect cables from meters or current transformers to pull boxes or switchboards, using hand tools.
- Attach pressurized meters to fixtures which submerge them in water, and observe meters for leaks.
- Advise customers on proper installation of valves or regulators and related equipment.
- Calibrate thermostats for specified temperature or pressure settings.
- Clean plant growth, scale, paint, soil, or rust from meter housings, using wire brushes, scrapers, buffers, sandblasters, or cleaning compounds.
- Connect hoses from provers to meter inlets and outlets, and raise prover bells until prover gauges register zero.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Remove drumheads by removing tension rods with drum keys and cutting tools.
- Remove material from bars of percussion instruments to obtain specified tones, using bandsaws, sanding machines, machine grinders, or hand files and scrapers.
- Disassemble instruments and parts for repair and adjustment.
- Play instruments to evaluate their sound quality and to locate any defects.
- Adjust string tensions to tune instruments, using hand tools and electronic tuning devices.
- Reassemble instruments following repair, using hand tools and power tools and glue, hair, yarn, resin, or clamps, and lubricate instruments as necessary.
- Repair or replace musical instrument parts and components, such as strings, bridges, felts, and keys, using hand and power tools.
- Inspect instruments to locate defects, and to determine their value or the level of restoration required.
- Compare instrument pitches with tuning tool pitches to tune instruments.
- String instruments, and adjust trusses and bridges of instruments to obtain specified string tensions and heights.
- Polish instruments, using rags and polishing compounds, buffing wheels, or burnishing tools.
- Repair cracks in wood or metal instruments, using pinning wire, lathes, fillers, clamps, or soldering irons.
- Mix and measure glue that will be used for instrument repair.
- Shape old parts and replacement parts to improve tone or intonation, using hand tools, lathes, or soldering irons.
- Refinish instruments to protect and decorate them, using hand tools, buffing tools, and varnish.
- Make wood replacement parts, using woodworking machines and hand tools.
- Align pads and keys on reed or wind instruments.
- Solder posts and parts to hold them in their proper places.
- Remove dents and burrs from metal instruments, using mallets and burnishing tools.
- Test tubes and pickups in electronic amplifier units, and solder parts and connections as necessary.
- Adjust felt hammers on pianos to increase tonal mellowness or brilliance, using sanding paddles, lacquer, or needles.
- Remove irregularities from tuning pins, strings, and hammers of pianos, using wood blocks or filing tools.
- Strike wood, fiberglass, or metal bars of instruments, and use tuned blocks, stroboscopes, or electronic tuners to evaluate tones made by instruments.
- Wash metal instruments in lacquer-stripping and cyanide solutions to remove lacquer and tarnish.
- Assemble and install new pipe organs and pianos in buildings.
- Refinish and polish piano cabinets or cases to prepare them for sale.
- Deliver pianos to purchasers or to locations of their use.
- Place rim hoops back onto drum shells to allow new drumheads to dry and become taut.
- Solder or weld frames of mallet instruments and metal drum parts.
- Repair breaks in percussion instruments, such as drums and cymbals, using drill presses, power saws, glue, clamps, grinding wheels, or other hand tools.
- Cut new drumheads from animal skins, using scissors, and soak drumheads in water to make them pliable.
- Assemble bars onto percussion instruments.
- Stretch drumheads over rim hoops and tuck them around and under the hoops, using hand tucking tools.
- Cut out sections around cracks on percussion instruments to prevent cracks from advancing, using shears or grinding wheels.
- Clean, sand, and paint parts of percussion instruments to maintain their condition.
- File metal reeds until their pitches correspond with standard tuning bar pitches.
- Replace xylophone bars and wheels.
- Remove drumheads by removing tension rods with drum keys and cutting tools.
- Remove material from bars of percussion instruments to obtain specified tones, using bandsaws, sanding machines, machine grinders, or hand files and scrapers.
- Disassemble instruments and parts for repair and adjustment.
- Remove or cut out defective parts or drill holes to gain access to internal defects or damage, using drills and punches.
- Remove, inspect, repair, and install in-flight refueling stores and external fuel tanks.
- Disassemble engines and inspect parts, such as turbine blades or cylinders, for corrosion, wear, warping, cracks, and leaks, using precision measuring instruments, x-rays, and magnetic inspection equipment.
- Examine and inspect aircraft components, including landing gear, hydraulic systems, and deicers to locate cracks, breaks, leaks, or other problems.
- Conduct routine and special inspections as required by regulations.
- Inspect completed work to certify that maintenance meets standards and that aircraft are ready for operation.
- Read and interpret maintenance manuals, service bulletins, and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.
- Maintain repair logs, documenting all preventive and corrective aircraft maintenance.
- Modify aircraft structures, space vehicles, systems, or components, following drawings, schematics, charts, engineering orders, and technical publications.
- Inspect airframes for wear or other defects.
- Measure parts for wear, using precision instruments.
- Obtain fuel and oil samples and check them for contamination.
- Maintain, repair, and rebuild aircraft structures, functional components, and parts, such as wings and fuselage, rigging, hydraulic units, oxygen systems, fuel systems, electrical systems, gaskets, or seals.
- Replace or repair worn, defective, or damaged components, using hand tools, gauges, and testing equipment.
- Read and interpret pilots' descriptions of problems to diagnose causes.
- Test operation of engines and other systems, using test equipment, such as ignition analyzers, compression checkers, distributor timers, or ammeters.
- Measure the tension of control cables.
- Spread plastic film over areas to be repaired to prevent damage to surrounding areas.
- Remove or install aircraft engines, using hoists or forklift trucks.
- Assemble and install electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools.
- Locate and mark dimensions and reference lines on defective or replacement parts, using templates, scribes, compasses, and steel rules.
- Fabricate defective sections or parts, using metal fabricating machines, saws, brakes, shears, and grinders.
- Reassemble engines following repair or inspection and reinstall engines in aircraft.
- Service and maintain aircraft and related apparatus by performing activities such as flushing crankcases, cleaning screens, and or moving parts.
- Clean, refuel, and change oil in line service aircraft.
- Trim and shape replacement body sections to specified sizes and fits and secure sections in place, using adhesives, hand tools, and power tools.
- Accompany aircraft on flights to make in-flight adjustments and corrections.
- Install and align repaired or replacement parts for subsequent riveting or welding, using clamps and wrenches.
- Inventory and requisition or order supplies, parts, materials, and equipment.
- Clean, strip, prime, and sand structural surfaces and materials to prepare them for bonding.
- Communicate with other workers to coordinate fitting and alignment of heavy parts, or to facilitate processing of repair parts.
- Examine engines through specially designed openings while working from ladders or scaffolds, or use hoists or lifts to remove the entire engine from an aircraft.
- Check for corrosion, distortion, and invisible cracks in the fuselage, wings, and tail, using x-ray and magnetic inspection equipment.
- Cure bonded structures, using portable or stationary curing equipment.
- Listen to operating engines to detect and diagnose malfunctions, such as sticking or burned valves.
- Clean engines, sediment bulk and screens, and carburetors, adjusting carburetor float levels.
- Determine repair limits for engine hot section parts.
- Prepare and paint aircraft surfaces.
- Remove or cut out defective parts or drill holes to gain access to internal defects or damage, using drills and punches.
- Remove, inspect, repair, and install in-flight refueling stores and external fuel tanks.
- Disassemble engines and inspect parts, such as turbine blades or cylinders, for corrosion, wear, warping, cracks, and leaks, using precision measuring instruments, x-rays, and magnetic inspection equipment.
- Set starter locks and align and repair steering or throttle controls, using gauges, screwdrivers, or wrenches.
- Repair engine mechanical equipment, such as power tilts, bilge pumps, or power take-offs.
- Inspect and repair or adjust propellers or propeller shafts.
- Disassemble and inspect motors to locate defective parts, using mechanic's hand tools and gauges.
- Start motors and monitor performance for signs of malfunctioning, such as smoke, excessive vibration, or misfiring.
- Document inspection and test results and work performed or to be performed.
- Mount motors to boats, and operate boats at various speeds on waterways to conduct operational tests.
- Perform routine engine maintenance on motorboats, such as changing oil and filters.
- Replace parts, such as gears, magneto points, piston rings, or spark plugs, and reassemble engines.
- Idle motors and observe thermometers to determine the effectiveness of cooling systems.
- Adjust carburetor mixtures, electrical point settings, or timing while motors are running in water-filled test tanks.
- Adjust generators and replace faulty wiring, using hand tools and soldering irons.
- Repair or rework parts, using machine tools such as lathes, mills, drills, or grinders.
- Set starter locks and align and repair steering or throttle controls, using gauges, screwdrivers, or wrenches.
- Repair engine mechanical equipment, such as power tilts, bilge pumps, or power take-offs.
- Inspect and repair or adjust propellers or propeller shafts.
- Disassemble and inspect motors to locate defective parts, using mechanic's hand tools and gauges.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
- Lift units or parts such as motors or generators, using cranes or chain hoists, or signal crane operators to lift heavy parts or subassemblies.
- Record repairs required, parts used, and labor time.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Lubricate moving parts.
- Read service guides to find information needed to perform repairs.
- Inspect electrical connections, wiring, relays, charging resistance boxes, and storage batteries, following wiring diagrams.
- Scrape and clean units or parts, using cleaning solvents and equipment such as buffing wheels.
- Weld, braze, or solder electrical connections.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Steam-clean polishing and buffing wheels to remove abrasives and bonding materials, and spray, brush, or recoat surfaces as necessary.
- Set machinery for proper performance, using computers.
- Test equipment for overheating, using speed gauges and thermometers.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Maintain stocks of parts.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Solder, wrap, and coat wires to ensure proper insulation.
- Rewire electrical systems, and repair or replace electrical accessories.
- Clean cells, cell assemblies, glassware, leads, electrical connections, and battery poles, using scrapers, steam, water, emery cloths, power grinders, or acid.
- Rewind coils on cores in slots, or make replacement coils, using coil-winding machines.
- Test conditions, fluid levels, and specific gravities of electrolyte cells, using voltmeters, hydrometers, and thermometers.
- Add water or acid to battery cell solutions to obtain specified concentrations.
- Pour compounds into transformer-case terminal openings to seal out moisture.
- Hammer out dents and twists in tools and equipment.
- Drain and filter transformer oil and refill transformers with oil until coils are submerged.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Repair and operate battery-charging equipment.
- Sharpen tools such as saws, picks, shovels, screwdrivers, and scoops, either manually or by using bench grinders and emery wheels.
- Inspect batteries for structural defects such as dented cans, damaged carbon rods and terminals, and defective seals.
- Test battery charges, and replace or recharge batteries as necessary.
- Bolt porcelain insulators to wood parts to assemble hot stools.
- Position and level battery cells, anodes, or cathodes, using hoists or leveling jacks, or signal other workers to perform positioning and leveling.
- Clean, rinse, and dry transformer cases, using boiling water, scrapers, solvents, hoses, and cloths.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Remove copper from circuit boards.
- Dismantle wrecked vehicles by removing parts and labeling and sorting parts into containers.
- Sort materials, such as metals, glass, wood, paper or plastics, into appropriate containers for recycling.
- Clean recycling yard by sweeping, raking, picking up broken glass and loose paper debris, or moving barrels and bins.
- Operate forklifts, pallet jacks, power lifts, or front-end loaders to load bales, bundles, or other heavy items onto trucks for shipping to smelters or other recycled materials processing facilities.
- Sort metals to separate high-grade metals, such as copper, brass, and aluminum, for recycling.
- Clean, inspect, or lubricate recyclable collection equipment or perform routine maintenance or minor repairs on recycling equipment, such as star gears, finger sorters, destoners, belts, and grinders.
- Collect and sort recyclable construction materials, such as concrete, drywall, plastics, or wood, into containers.
- Extract chemicals from discarded appliances, such as air conditioners or refrigerators, using specialized machinery, such as refrigerant recovery equipment.
- Deposit recoverable materials into chutes or place materials on conveyor belts.
- Operate balers to compress recyclable materials into bundles or bales.
- Clean materials, such as metals, according to recycling requirements.
- Record logs of recycled materials or waste chemicals removed from products.
- Operate processing equipment, such as fiber-sorters and grinders, to sort, crush, or grind recyclable materials.
- Cut discarded products, such as appliances and automobiles, into small pieces using saws, blow torches, or other hand or power tools.
- Collect recyclable materials from curbside for delivery to designated facilities.
- Operate automated refuse or manual recycling collection vehicles.
- Operate shredders to reclaim steel from discarded appliances.
- Remove copper from circuit boards.
- Dismantle wrecked vehicles by removing parts and labeling and sorting parts into containers.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Move and set up mobile homes or prefabricated buildings on owners' lots or at mobile home parks.
- Inspect, examine, and test the operation of parts or systems to evaluate operating condition and to determine if repairs are needed.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of plumbing fixtures.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, and diagrams.
- Confer with customers or read work orders to determine the nature and extent of damage to units.
- Install, repair, and replace units, fixtures, appliances, and other items and systems in mobile and modular homes, prefabricated buildings, or travel trailers, using hand tools or power tools.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Repair leaks in plumbing or gas lines, using caulking compounds and plastic or copper pipe.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, and hand tools.
- Open and close doors, windows, and drawers to test their operation, trimming edges to fit, using jackplanes or drawknives.
- Connect electrical systems to outside power sources and activate switches to test the operation of appliances and light fixtures.
- Refinish wood surfaces on cabinets, doors, moldings, and floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- Disassemble malfunctioning equipment and remove, repair, or replace defective parts, such as motors, clutches, or transformers.
- Test or calibrate components or equipment, following manufacturers' manuals and troubleshooting techniques, using hand tools, power tools, or measuring devices.
- Perform preventive maintenance or service, such as cleaning, lubricating, or adjusting equipment.
- Inspect, test, or troubleshoot malfunctioning medical or related equipment, following manufacturers' specifications and using test and analysis instruments.
- Keep records of maintenance, repair, and required updates of equipment.
- Examine medical equipment or facility's structural environment and check for proper use of equipment to protect patients and staff from electrical or mechanical hazards and to ensure compliance with safety regulations.
- Install medical equipment.
- Test, evaluate, and classify excess or in-use medical equipment and determine serviceability, condition, and disposition, in accordance with regulations.
- Plan and carry out work assignments, using blueprints, schematic drawings, technical manuals, wiring diagrams, or liquid or air flow sheets, following prescribed regulations, directives, or other instructions as required.
- Study technical manuals or attend training sessions provided by equipment manufacturers to maintain current knowledge.
- Explain or demonstrate correct operation or preventive maintenance of medical equipment to personnel.
- Research catalogs or repair part lists to locate sources for repair parts, requisitioning parts and recording their receipt.
- Repair shop equipment, metal furniture, or hospital equipment, including welding broken parts or replacing missing parts, or bring item into local shop for major repairs.
- Solder loose connections, using soldering iron.
- Compute power and space requirements for installing medical, dental, or related equipment and install units to manufacturers' specifications.
- Evaluate technical specifications to identify equipment or systems best suited for intended use and possible purchase, based on specifications, user needs, or technical requirements.
- Contribute expertise to develop medical maintenance standard operating procedures.
- Fabricate, dress down, or substitute parts or major new items to modify equipment to meet unique operational or research needs, working from job orders, sketches, modification orders, samples, or discussions with operating officials.
- Supervise or advise subordinate personnel.
- Make computations relating to load requirements of wiring or equipment, using algebraic expressions and standard formulas.
- Disassemble malfunctioning equipment and remove, repair, or replace defective parts, such as motors, clutches, or transformers.
- Repair ships, bridge foundations, or other structures below the water line, using caulk, bolts, and hand tools.
- Take appropriate safety precautions, such as monitoring dive lengths and depths and registering with authorities before diving expeditions begin.
- Check and maintain diving equipment, such as helmets, masks, air tanks, harnesses, or gauges.
- Communicate with workers on the surface while underwater, using signal lines or telephones.
- Descend into water with the aid of diver helpers, using scuba gear or diving suits.
- Obtain information about diving tasks and environmental conditions.
- Supervise or train other divers, including hobby divers.
- Inspect the condition of underwater steel or wood structures.
- Inspect and test docks, ships, buoyage systems, plant intakes or outflows, or underwater pipelines, cables, or sewers, using closed circuit television, still photography, and testing equipment.
- Recover objects by placing rigging around sunken objects, hooking rigging to crane lines, and operating winches, derricks, or cranes to raise objects.
- Operate underwater video, sonar, recording, or related equipment to investigate underwater structures or marine life.
- Take test samples or photographs to assess the condition of vessels or structures.
- Cut and weld steel, using underwater welding equipment, jigs, and supports.
- Install, inspect, clean, or repair piping or valves.
- Carry out non-destructive testing, such as tests for cracks on the legs of oil rigs at sea.
- Install pilings or footings for piers or bridges.
- Salvage wrecked ships or their cargo, using pneumatic power velocity and hydraulic tools and explosive charges, when necessary.
- Remove obstructions from strainers or marine railway or launching ways, using pneumatic or power hand tools.
- Set or guide placement of pilings or sandbags to provide support for structures, such as docks, bridges, cofferdams, or platforms.
- Perform activities related to underwater search and rescue, salvage, recovery, or cleanup operations.
- Perform offshore oil or gas exploration or extraction duties, such as conducting underwater surveys or repairing and maintaining drilling rigs or platforms.
- Drill holes in rock and rig explosives for underwater demolitions.
- Remove rubbish or pollution from the sea.
- Set up dive sites for recreational instruction.
- Cultivate or harvest marine species or perform routine work on fish farms.
- Repair ships, bridge foundations, or other structures below the water line, using caulk, bolts, and hand tools.
- Remove or disassemble defective automatic mechanical door closers, using hand tools.
- Wind large springs with upward motion of arm.
- Adjust doors to open or close with the correct amount of effort, or make simple adjustments to electric openers.
- Carry springs to tops of doors, using ladders or scaffolding, and attach springs to tracks to install spring systems.
- Repair or replace worn or broken door parts, using hand tools.
- Complete required paperwork, such as work orders, according to services performed or required.
- Fasten angle iron back-hangers to ceilings and tracks, using fasteners or welding equipment.
- Collect payment upon job completion.
- Install door frames, rails, steel rolling curtains, electronic-eye mechanisms, or electric door openers and closers, using power tools, hand tools, and electronic test equipment.
- Inspect job sites, assessing headroom, side room, or other conditions to determine appropriateness of door for a given location.
- Assemble and fasten tracks to structures or bucks, using impact wrenches or welding equipment.
- Set doors into place or stack hardware sections into openings after rail or track installation.
- Operate lifts, winches, or chain falls to move heavy curtain doors.
- Fabricate replacements for worn or broken parts, using welders, lathes, drill presses, or shaping or milling machines.
- Prepare doors for hardware installation, such as drilling holes to install locks.
- Run low voltage wiring on ceiling surfaces, using insulated staples.
- Cut door stops or angle irons to fit openings.
- Study blueprints and schematic diagrams to determine appropriate methods of installing or repairing automated door openers.
- Install dock seals, bumpers, or shelters.
- Order replacement springs, sections, or slats.
- Lubricate door closer oil chambers, and pack spindles with leather washers.
- Set in and secure floor treadles for door-activating mechanisms, and connect power packs and electrical panelboards to treadles.
- Cover treadles with carpeting or other floor covering materials, and test systems by operating treadles.
- Bore or cut holes in flooring as required for installation, using hand or power tools.
- Clean door closer parts, using caustic soda, rotary brushes, or grinding wheels.
- Remove or disassemble defective automatic mechanical door closers, using hand tools.
- Repair or remove and replace system components.
- Shut off steam, water, or other gases or liquids from pipe sections, using valve keys or wrenches.
- Install underground storm, sanitary, or water piping systems, extending piping as needed to connect fixtures and plumbing.
- Assemble pipe sections, tubing, or fittings, using couplings, clamps, screws, bolts, cement, plastic solvent, caulking, or soldering, brazing, or welding equipment.
- Locate and mark the position of pipe installations, connections, passage holes, or fixtures in structures, using measuring instruments such as rulers or levels.
- Cut, thread, or hammer pipes to specifications, using tools such as saws, cutting torches, pipe threaders, or pipe benders.
- Lay out full scale drawings of pipe systems, supports, or related equipment, according to blueprints.
- Plan pipe system layout, installation, or repair, according to specifications.
- Review blueprints, building codes, or specifications to determine work details or procedures.
- Select pipe sizes, types, or related materials, such as supports, hangers, or hydraulic cylinders, according to specifications.
- Fill pipes or plumbing fixtures with water or air and observe pressure gauges to detect and locate leaks.
- Direct helpers engaged in pipe cutting, preassembly, or installation of plumbing systems or components.
- Inspect, examine, or test installed systems or pipe lines, using pressure gauge, hydrostatic testing, observation, or other methods.
- Install pipe assemblies, fittings, valves, appliances such as dishwashers or water heaters, or fixtures such as sinks or toilets, using hand or power tools.
- Anchor steel supports from ceiling joists to hold pipes in place.
- Attach pipes to walls, structures, or fixtures, such as radiators or tanks, using brackets, clamps, tools, or welding equipment.
- Modify, clean, or maintain pipe systems, units, fittings, or related machines or equipment, using hand or power tools.
- Install automatic controls to regulate pipe systems.
- Estimate time, material, or labor costs for use in project plans.
- Keep records of work assignments.
- Inspect structures to assess material or equipment needs, to establish the sequence of pipe installations, or to plan installation around obstructions, such as electrical wiring.
- Maintain or repair plumbing by replacing defective washers, replacing or mending broken pipes, or opening clogged drains.
- Cut openings in structures to accommodate pipes or pipe fittings, using hand or power tools.
- Install green plumbing equipment, such as faucet flow restrictors, dual-flush or pressure-assisted flush toilets, or tankless hot water heaters.
- Inspect work sites for obstructions or holes that could cause structural weakness.
- Install pipe systems to support alternative energy-fueled systems, such as geothermal heating or cooling systems.
- Install fixtures, appliances, or equipment designed to reduce water or energy consumption.
- Repair hydraulic or air pumps.
- Weld small pipes or special piping, using specialized techniques, equipment, or materials, such as computer-assisted welding or microchip fabrication.
- Operate motorized pumps to remove water from flooded manholes, basements, or facility floors.
- Repair or remove and replace system components.
