- Start pumps that circulate mud through drill pipes and boreholes to cool drill bits and flush out drill cuttings.
Occupations with related tasks Save Table: XLSX CSV
- Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.
- Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings or walls.
- Lubricate, clean, or repair machinery, equipment, or tools.
- Signal equipment operators to facilitate alignment, movement, or adjustment of machinery, equipment, or materials.
- Read plans, instructions, or specifications to determine work activities.
- Measure, mark, or record openings or distances to layout areas where construction work will be performed.
- Clean or prepare construction sites to eliminate possible hazards.
- Dig ditches or trenches, backfill excavations, or compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, or rakes.
- Load, unload, or identify building materials, machinery, or tools, distributing them to the appropriate locations, according to project plans or specifications.
- Position, join, align, or seal structural components, such as concrete wall sections or pipes.
- Perform site activities required of green certified construction practices, such as implementing waste management procedures, identifying materials for reuse, or installing erosion or sedimentation control mechanisms.
- Control traffic passing near, in, or around work zones.
- Install sewer, water, or storm drain pipes, using pipe-laying machinery or laser guidance equipment.
- Operate or maintain air monitoring or other sampling devices in confined or hazardous environments.
- Smooth or finish freshly poured cement or concrete, using floats, trowels, screeds, or powered cement finishing tools.
- Erect or dismantle scaffolding, shoring, braces, traffic barricades, ramps, or other temporary structures.
- Provide assistance to craft workers, such as carpenters, plasterers, or masons.
- Perform building weatherization tasks, such as repairing windows, adding insulation, or applying weather-stripping materials.
- Apply weather-stripping to reduce energy loss.
- Spray materials, such as water, sand, steam, vinyl, paint, or stucco, through hoses to clean, coat, or seal surfaces.
- Raze buildings or salvage useful materials.
- Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.
- Position or dismantle forms for pouring concrete, using saws, hammers, nails, or bolts.
- Grind, scrape, sand, or polish surfaces, such as concrete, marble, terrazzo, or wood flooring, using abrasive tools or machines.
- Place, consolidate, or protect case-in-place concrete or masonry structures.
- Mix ingredients to create compounds for covering or cleaning surfaces.
- Mix, pour, or spread concrete, using portable cement mixers.
- Operate jackhammers or drills to break up concrete or pavement.
- Apply caulking compounds by hand or caulking guns to protect against entry of water or air.
- Identify, pack, or transport hazardous or radioactive materials.
- Use computers or other input devices to control robotic pipe cutters or cleaners.
- Perform construction laborer duties at green building sites, such as renewable energy plants or wind turbine installations.
- Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.
- Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings or walls.
- Operate pumps that circulate water, oil, or other fluids through wells to remove sand or other materials obstructing the free flow of oil.
- Maintain and perform safety inspections on equipment and tools.
- Operate controls that raise derricks or level rigs.
- Listen to engines, rotary chains, or other equipment to detect faulty operations or unusual well conditions.
- Prepare reports of services rendered, tools used, or time required, for billing purposes.
- Install pressure-control devices onto wellheads.
- Confer with others to gather information regarding pipe or tool sizes or borehole conditions in wells.
- Drive truck-mounted units to well sites.
- Interpret instrument readings to ascertain the depth of obstruction.
- Thread cables through derrick pulleys, using hand tools.
- Select fishing methods or tools for removing obstacles such as liners, broken casing, screens, or drill pipe.
- Close and seal wells no longer in use.
- Direct drilling crews performing activities such as assembling and connecting pipe, applying weights to drill pipes, or drilling around lodged obstacles.
- Apply green technologies or techniques, such as the use of coiled tubing, slim-hole drilling, horizontal drilling, hydraulic fracturing, or gas lift systems.
- Operate specialized equipment to remove obstructions by backing off or severing pipes by chemical or explosive action.
- Perforate well casings or sidewalls of boreholes with explosive charges.
- Examine unserviceable wells to determine actions to be taken to improve well conditions.
- Monitor sound wave-generating or detecting mechanisms to determine well fluid levels.
- Insert detection instruments into wells with obstructions.
- Operate pumps that circulate water, oil, or other fluids through wells to remove sand or other materials obstructing the free flow of oil.
- Start and examine operation of slush pumps to ensure circulation and consistency of drilling fluid or mud in well.
- Train crews, and introduce procedures to make drill work more safe and effective.
- Observe pressure gauge and move throttles and levers to control the speed of rotary tables, and to regulate pressure of tools at bottoms of boreholes.
- Count sections of drill rod to determine depths of boreholes.
- Push levers and brake pedals to control gasoline, diesel, electric, or steam draw works that lower and raise drill pipes and casings in and out of wells.
- Connect sections of drill pipe, using hand tools and powered wrenches and tongs.
- Maintain records of footage drilled, location and nature of strata penetrated, materials and tools used, services rendered, and time required.
- Maintain and adjust machinery to ensure proper performance.
- Locate and recover lost or broken bits, casings, and drill pipes from wells, using special tools.
- Weigh clay, and mix with water and chemicals to make drilling mud.
- Direct rig crews in drilling and other activities, such as setting up rigs and completing or servicing wells.
- Monitor progress of drilling operations, and select and change drill bits according to the nature of strata, using hand tools.
- Repair or replace defective parts of machinery, such as rotary drill rigs, water trucks, air compressors, and pumps, using hand tools.
- Clean and oil pulleys, blocks, and cables.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Remove core samples during drilling to determine the nature of the strata being drilled.
- Cap wells with packers, or turn valves, to regulate outflow of oil from wells.
- Line drilled holes with pipes, and install all necessary hardware, to prepare new wells.
- Position and prepare truck-mounted derricks at drilling areas specified on field maps.
- Plug observation wells, and restore sites.
- Lower and explode charges in boreholes to start flow of oil from wells.
- Dig holes, set forms, and mix and pour concrete, for foundations of steel or wooden derricks.
- Start and examine operation of slush pumps to ensure circulation and consistency of drilling fluid or mud in well.
- Turn valves to control air or water output of compressors or pumps.
- Learn and follow safety regulations.
- Take actions to avoid potential hazards or obstructions, such as utility lines, other equipment, other workers, or falling objects.
- Start engines, move throttles, switches, or levers, or depress pedals to operate machines, such as bulldozers, trench excavators, road graders, or backhoes.
- Coordinate machine actions with other activities, positioning or moving loads in response to hand or audio signals from crew members.
- Align machines, cutterheads, or depth gauge makers with reference stakes and guidelines or ground or position equipment, following hand signals of other workers.
- Locate underground services, such as pipes or wires, prior to beginning work.
- Signal operators to guide movement of tractor-drawn machines.
- Repair and maintain equipment, making emergency adjustments or assisting with major repairs as necessary.
- Load and move dirt, rocks, equipment, or other materials, using trucks, crawler tractors, power cranes, shovels, graders, or related equipment.
- Drive and maneuver equipment equipped with blades in successive passes over working areas to remove topsoil, vegetation, or rocks or to distribute and level earth or terrain.
- Operate tractors or bulldozers to perform such tasks as clearing land, mixing sludge, trimming backfills, or building roadways or parking lots.
- Monitor operations to ensure that health and safety standards are met.
- Connect hydraulic hoses, belts, mechanical linkages, or power takeoff shafts to tractors.
- Select and fasten bulldozer blades or other attachments to tractors, using hitches.
- Operate loaders to pull out stumps, rip asphalt or concrete, rough-grade properties, bury refuse, or perform general cleanup.
- Operate equipment to demolish or remove debris or to remove snow from streets, roads, or parking lots.
- Keep records of material or equipment usage or problems encountered.
- Adjust handwheels and depress pedals to control attachments, such as blades, buckets, scrapers, or swing booms.
- Check fuel supplies at sites to ensure adequate availability.
- Perform specialized work, using equipment, such as pile drivers, dredging rigs, drillers, or concrete pumpers.
- Talk to clients and study instructions, plans, or diagrams to establish work requirements.
- Drive tractor-trailer trucks to move equipment from site to site.
- Push other equipment when extra traction or assistance is required.
- Operate road watering, oiling, or rolling equipment, or street sealing equipment, such as chip spreaders.
- Operate compactors, scrapers, or rollers to level, compact, or cover refuse at disposal grounds.
- Test atmosphere for adequate oxygen or explosive conditions when working in confined spaces.
- Compile cost estimates for jobs.
- Turn valves to control air or water output of compressors or pumps.
- Pour water into wells, or pump water or slush into wells to cool drill bits and to remove drillings.
- Operate controls to stabilize machines and to position and align drills.
- Start, stop, and control drilling speed of machines and insertion of casings into holes.
- Regulate air pressure, rotary speed, and downward pressure, according to the type of rock or concrete being drilled.
- Select and attach drill bits and drill rods, adding more rods as hole depths increase, and changing drill bits as needed.
- Drive or guide truck-mounted equipment into position, level and stabilize rigs, and extend telescoping derricks.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Verify depths and alignments of boring positions.
- Perform routine maintenance and upgrade work on machines and equipment, such as replacing parts, building up drill bits, and lubricating machinery.
- Select the appropriate drill for the job, using knowledge of rock or soil conditions.
- Document geological formations encountered during work.
- Drive trucks, tractors, or truck-mounted drills to and from work sites.
- Assemble and position machines, augers, casing pipes, and other equipment, using hand and power tools.
- Record drilling progress and geological data.
- Retrieve lost equipment from bore holes, using retrieval tools and equipment.
- Fabricate well casings.
- Create and lay out designs for drill and blast patterns.
- Place and install screens, casings, pumps, and other well fixtures to develop wells.
- Operate water-well drilling rigs and other equipment to drill, bore, and dig for water wells or for environmental assessment purposes.
- Review client requirements and proposed locations for drilling operations to determine feasibility, and to determine cost estimates.
- Drill or bore holes in rock for blasting, grouting, anchoring, or building foundations.
- Perform pumping tests to assess well performance.
- Disinfect, reconstruct, and redevelop contaminated wells and water pumping systems, and clean and disinfect new wells in preparation for use.
- Design well pumping systems.
- Signal crane operators to move equipment.
- Withdraw drill rods from holes, and extract core samples.
- Inspect core samples to determine nature of strata, or take samples to laboratories for analysis.
- Retract augers to force discharge dirt from holes.
- Observe electronic graph recorders and flow meters that monitor the water used to flush debris from holes.
- Monitor drilling operations, by checking gauges and listening to equipment to assess drilling conditions and to determine the need to adjust drilling or alter equipment.
- Pour water into wells, or pump water or slush into wells to cool drill bits and to remove drillings.
- Operate motorized pumps to remove water from flooded manholes, basements, or facility floors.
- Shut off steam, water, or other gases or liquids from pipe sections, using valve keys or wrenches.
- Install underground storm, sanitary, or water piping systems, extending piping as needed to connect fixtures and plumbing.
- Assemble pipe sections, tubing, or fittings, using couplings, clamps, screws, bolts, cement, plastic solvent, caulking, or soldering, brazing, or welding equipment.
- Locate and mark the position of pipe installations, connections, passage holes, or fixtures in structures, using measuring instruments such as rulers or levels.
- Cut, thread, or hammer pipes to specifications, using tools such as saws, cutting torches, pipe threaders, or pipe benders.
- Lay out full scale drawings of pipe systems, supports, or related equipment, according to blueprints.
- Plan pipe system layout, installation, or repair, according to specifications.
- Review blueprints, building codes, or specifications to determine work details or procedures.
- Select pipe sizes, types, or related materials, such as supports, hangers, or hydraulic cylinders, according to specifications.
- Fill pipes or plumbing fixtures with water or air and observe pressure gauges to detect and locate leaks.
- Direct helpers engaged in pipe cutting, preassembly, or installation of plumbing systems or components.
- Inspect, examine, or test installed systems or pipe lines, using pressure gauge, hydrostatic testing, observation, or other methods.
- Install pipe assemblies, fittings, valves, appliances such as dishwashers or water heaters, or fixtures such as sinks or toilets, using hand or power tools.
- Anchor steel supports from ceiling joists to hold pipes in place.
- Attach pipes to walls, structures, or fixtures, such as radiators or tanks, using brackets, clamps, tools, or welding equipment.
- Modify, clean, or maintain pipe systems, units, fittings, or related machines or equipment, using hand or power tools.
- Install automatic controls to regulate pipe systems.
- Estimate time, material, or labor costs for use in project plans.
- Keep records of work assignments.
- Inspect structures to assess material or equipment needs, to establish the sequence of pipe installations, or to plan installation around obstructions, such as electrical wiring.
- Maintain or repair plumbing by replacing defective washers, replacing or mending broken pipes, or opening clogged drains.
- Repair or remove and replace system components.
- Cut openings in structures to accommodate pipes or pipe fittings, using hand or power tools.
- Install green plumbing equipment, such as faucet flow restrictors, dual-flush or pressure-assisted flush toilets, or tankless hot water heaters.
- Inspect work sites for obstructions or holes that could cause structural weakness.
- Install pipe systems to support alternative energy-fueled systems, such as geothermal heating or cooling systems.
- Install fixtures, appliances, or equipment designed to reduce water or energy consumption.
- Repair hydraulic or air pumps.
- Weld small pipes or special piping, using specialized techniques, equipment, or materials, such as computer-assisted welding or microchip fabrication.
- Operate motorized pumps to remove water from flooded manholes, basements, or facility floors.
