Job Duties Custom List 47-2121.00 — Glaziers
- Confer with customers to determine project requirements or to provide cost estimates.
Occupations with related tasks Save Table: XLSX CSV
- Recommend weatherization techniques to clients in accordance with needs and applicable energy regulations, codes, policies, or statutes.
- Contact residents or building owners to schedule appointments.
- Explain recommendations, policies, procedures, requirements, or other related information to residents or building owners.
- Explain energy conservation measures, such as the use of low flow showerheads and energy-efficient lighting.
- Test combustible appliances, such as gas appliances.
- Determine amount of air leakage in buildings, using a blower door machine.
- Test and diagnose air flow systems, using furnace efficiency analysis equipment.
- Install and seal air ducts, combustion air openings, or ventilation openings to improve heating and cooling efficiency.
- Inspect buildings to identify required weatherization measures, including repair work, modification, or replacement.
- Apply insulation materials, such as loose, blanket, board, and foam insulation to attics, crawl spaces, basements, or walls.
- Make minor repairs using basic hand or power tools and materials, such as glass, lumber, and drywall.
- Prepare cost estimates or specifications for rehabilitation or weatherization services.
- Wrap air ducts and water lines with insulating materials, such as duct wrap and pipe insulation.
- Prepare and apply weather-stripping, glazing, caulking, or door sweeps to reduce energy losses.
- Clean and maintain tools and equipment.
- Apply spackling, compounding, or other materials to repair holes in walls.
- Maintain activity logs, financial transaction logs, or other records of weatherization work performed.
- Prepare or assist in the preparation of bids, contracts, or written reports related to weatherization work.
- Install storm windows or storm doors and verify proper fit.
- Wrap water heaters with water heater blankets.
- Recommend weatherization techniques to clients in accordance with needs and applicable energy regulations, codes, policies, or statutes.
- Contact residents or building owners to schedule appointments.
- Explain recommendations, policies, procedures, requirements, or other related information to residents or building owners.
- Explain energy conservation measures, such as the use of low flow showerheads and energy-efficient lighting.
- Discuss the design with the client.
- Prepare base for installation by removing unstable or unsuitable materials, compacting and grading the soil, draining or stabilizing weak or saturated soils and taking measures to prevent water penetration and migration of bedding sand.
- Supply and place base materials, edge restraints, bedding sand and jointing sand.
- Set pavers, aligning and spacing them correctly.
- Sweep sand into the joints and compact pavement until the joints are full.
- Screed sand level to an even thickness, and recheck sand exposed to elements, raking and rescreeding if necessary.
- Cut paving stones to size and for edges, using a splitter and a masonry saw.
- Compact bedding sand and pavers to finish the paved area, using a plate compactor.
- Design paver installation layout pattern and create markings for directional references of joints and stringlines.
- Sweep sand from the surface prior to opening to traffic.
- Resurface an outside area with cobblestones, terracotta tiles, concrete or other materials.
- Cement the edges of the paved area.
- Discuss the design with the client.
- Confer with owners, violators, or authorities to explain regulations or recommend remedial actions.
- Monitor installation of plumbing, wiring, equipment, or appliances to ensure that installation is performed properly and is in compliance with applicable regulations.
- Approve building plans that meet required specifications.
- Inspect and monitor construction sites to ensure adherence to safety standards, building codes, or specifications.
- Inspect bridges, dams, highways, buildings, wiring, plumbing, electrical circuits, sewers, heating systems, or foundations during and after construction for structural quality, general safety, or conformance to specifications and codes.
- Review and interpret plans, blueprints, site layouts, specifications, or construction methods to ensure compliance to legal requirements and safety regulations.
- Maintain daily logs and supplement inspection records with photographs.
- Conduct inspections, using survey instruments, metering devices, tape measures, or test equipment.
- Measure dimensions and verify level, alignment, or elevation of structures or fixtures to ensure compliance to building plans and codes.
- Train, direct, or supervise other construction inspectors.
- Issue permits for construction, relocation, demolition, or occupancy.
- Conduct environmental hazard inspections to identify or quantify problems, such as asbestos, poor air quality, water contamination, or other environmental hazards.
- Evaluate premises for cleanliness, such as proper garbage disposal or lack of vermin infestation.
- Monitor construction activities to ensure that environmental regulations are not violated.
- Evaluate project details to ensure adherence to environmental regulations.
- Estimate cost of completed work or of needed renovations or upgrades.
- Examine lifting or conveying devices, such as elevators, escalators, moving sidewalks, hoists, inclined railways, ski lifts, or amusement rides to ensure safety and proper functioning.
- Sample and test air to identify gasses, such as bromine, ozone, or sulfur dioxide, or particulates, such as mold, dust, or allergens.
- Inspect facilities or installations to determine their environmental impact.
- Confer with owners, violators, or authorities to explain regulations or recommend remedial actions.
- Discuss fencing needs with customers, and estimate and quote prices.
- Establish the location for a fence, and gather information needed to ensure that there are no electric cables or water lines in the area.
- Set metal or wooden posts in upright positions in postholes.
- Measure and lay out fence lines and mark posthole positions, following instructions, drawings, or specifications.
- Align posts, by lines or sighting, and verify vertical alignment of posts, using plumb bobs or spirit levels.
- Attach rails or tension wire along bottoms of posts to form fencing frames.
- Dig postholes, using spades, posthole diggers, or power-driven augers.
- Attach fence rail supports to posts, using hammers and pliers.
- Assemble gates, and fasten gates into position, using hand tools.
- Mix and pour concrete around bases of posts, or tamp soil into postholes to embed posts.
- Make rails for fences, by sawing lumber or by cutting metal tubing to required lengths.
- Nail top and bottom rails to fence posts, or insert them in slots on posts.
- Stretch wire, wire mesh, or chain link fencing between posts, and attach fencing to frames.
- Complete top fence rails of metal fences by connecting tube sections, using metal sleeves.
- Erect alternate panel, basket weave, and louvered fences.
- Insert metal tubing through rail supports.
- Nail pointed slats to rails to construct picket fences.
- Construct and repair barriers, retaining walls, trellises, and other types of fences, walls, and gates.
- Weld metal parts together, using portable gas welding equipment.
- Blast rock formations and rocky areas with dynamite to facilitate posthole digging.
- Discuss fencing needs with customers, and estimate and quote prices.
- Demonstrate start-up, shut-down, maintenance, diagnostic, and safety procedures to thermal system owners.
- Test operation or functionality of mechanical, plumbing, electrical, and control systems.
- Apply weather seal, such as pipe flashings and sealants, to roof penetrations and structural devices.
- Install solar collector mounting devices on tile, asphalt, shingle, or built-up gravel roofs, using appropriate materials and penetration methods.
- Install copper or plastic plumbing using pipes, fittings, pipe cutters, acetylene torches, solder, wire brushes, sand cloths, flux, plastic pipe cleaners, or plastic glue.
- Identify plumbing, electrical, environmental, or safety hazards associated with solar thermal installations.
- Install circulating pumps using pipe, fittings, soldering equipment, electrical supplies, and hand tools.
- Install flat-plat, evacuated glass, or concentrating solar collectors on mounting devices, using brackets or struts.
- Install solar thermal system controllers and sensors.
- Fill water tanks and check tanks, pipes, and fittings for leaks.
- Design active direct or indirect, passive direct or indirect, or pool solar systems.
- Determine locations for installing solar subsystem components, including piping, water heaters, valves, and ancillary equipment.
- Perform routine maintenance or repairs to restore solar thermal systems to baseline operating conditions.
- Install heat exchangers and heat exchanger fluids according to installation manuals and schematics.
- Apply operation or identification tags or labels to system components, as required.
- Connect water heaters and storage tanks to power and water sources.
- Cut, miter, and glue piping insulation to insulate plumbing pipes and fittings.
- Install plumbing, such as dip tubes, port fittings, drain tank valves, pressure temperature relief valves, or tanks, according to manufacturer specifications and building codes.
- Install monitoring system components, such as flow meters, temperature gauges, and pressure gauges, according to system design and manufacturer specifications.
- Assess collector sites to ensure structural integrity of potential mounting surfaces or the best orientation and tilt for solar collectors.
- Apply ultraviolet radiation protection to prevent degradation of plumbing.
- Demonstrate start-up, shut-down, maintenance, diagnostic, and safety procedures to thermal system owners.
- Assist customers in selection of tile and grout.
- Align and straighten tile using levels, squares, and straightedges.
- Finish and dress the joints and wipe excess grout from between tiles, using damp sponge.
- Cut and shape tile to fit around obstacles and into odd spaces and corners, using hand and power cutting tools.
- Determine and implement the best layout to achieve a desired pattern.
- Mix, apply, and spread plaster, concrete, mortar, cement, mastic, glue or other adhesives to form a bed for the tiles, using brush, trowel and screed.
- Study blueprints and examine surface to be covered to determine amount of material needed.
- Measure and mark surfaces to be tiled, following blueprints.
- Lay and set mosaic tiles to create decorative wall, mural, and floor designs.
- Apply mortar to tile back, position the tile, and press or tap with trowel handle to affix tile to base.
- Mix and apply mortar or cement to edges and ends of drain tiles to seal halves and joints.
- Apply a sealer to make grout stain- and water-resistant.
- Level concrete and allow to dry.
- Measure and cut metal lath to size for walls and ceilings, using tin snips.
- Install and anchor fixtures in designated positions, using hand tools.
- Prepare surfaces for tiling by attaching lath or waterproof paper, or by applying a cement mortar coat to a metal screen.
- Remove and replace cracked or damaged tile.
- Cut tile backing to required size, using shears.
- Remove any old tile, grout and adhesive using chisels and scrapers and clean the surface carefully.
- Cut, surface, polish, and install marble and granite or install pre-cast terrazzo, granite or marble units.
- Spread mastic or other adhesive base on roof deck to form base for promenade tile, using serrated spreader.
- Prepare cost and labor estimates, based on calculations of time and materials needed for project.
- Brush glue onto manila paper on which design has been drawn and position tiles, finished side down, onto paper.
- Select and order tile and other items to be installed, such as bathroom accessories, walls, panels, and cabinets, according to specifications.
- Build underbeds and install anchor bolts, wires, and brackets.
- Assist customers in selection of tile and grout.
- Talk to clients and study instructions, plans, or diagrams to establish work requirements.
- Learn and follow safety regulations.
- Take actions to avoid potential hazards or obstructions, such as utility lines, other equipment, other workers, or falling objects.
- Start engines, move throttles, switches, or levers, or depress pedals to operate machines, such as bulldozers, trench excavators, road graders, or backhoes.
- Coordinate machine actions with other activities, positioning or moving loads in response to hand or audio signals from crew members.
- Align machines, cutterheads, or depth gauge makers with reference stakes and guidelines or ground or position equipment, following hand signals of other workers.
- Locate underground services, such as pipes or wires, prior to beginning work.
- Signal operators to guide movement of tractor-drawn machines.
- Repair and maintain equipment, making emergency adjustments or assisting with major repairs as necessary.
- Load and move dirt, rocks, equipment, or other materials, using trucks, crawler tractors, power cranes, shovels, graders, or related equipment.
- Drive and maneuver equipment equipped with blades in successive passes over working areas to remove topsoil, vegetation, or rocks or to distribute and level earth or terrain.
- Operate tractors or bulldozers to perform such tasks as clearing land, mixing sludge, trimming backfills, or building roadways or parking lots.
- Monitor operations to ensure that health and safety standards are met.
- Connect hydraulic hoses, belts, mechanical linkages, or power takeoff shafts to tractors.
- Select and fasten bulldozer blades or other attachments to tractors, using hitches.
- Operate loaders to pull out stumps, rip asphalt or concrete, rough-grade properties, bury refuse, or perform general cleanup.
- Operate equipment to demolish or remove debris or to remove snow from streets, roads, or parking lots.
- Keep records of material or equipment usage or problems encountered.
- Adjust handwheels and depress pedals to control attachments, such as blades, buckets, scrapers, or swing booms.
- Check fuel supplies at sites to ensure adequate availability.
- Perform specialized work, using equipment, such as pile drivers, dredging rigs, drillers, or concrete pumpers.
- Drive tractor-trailer trucks to move equipment from site to site.
- Push other equipment when extra traction or assistance is required.
- Operate road watering, oiling, or rolling equipment, or street sealing equipment, such as chip spreaders.
- Operate compactors, scrapers, or rollers to level, compact, or cover refuse at disposal grounds.
- Test atmosphere for adequate oxygen or explosive conditions when working in confined spaces.
- Compile cost estimates for jobs.
- Turn valves to control air or water output of compressors or pumps.
- Talk to clients and study instructions, plans, or diagrams to establish work requirements.
