- Climb poles or use truck-mounted buckets to access equipment.
Occupations with related tasks Save Table: XLSX CSV
- Climb towers to access components, using safety equipment, such as full-body harnesses.
- Climb communication towers to install, replace, or repair antennas or auxiliary equipment used to transmit and receive radio waves.
- Inspect completed work to ensure all hardware is tight, antennas are level, hangers are properly fastened, proper support is in place, or adequate weather proofing has been installed.
- Run appropriate power, ground, or coaxial cables.
- Test operation of tower transmission components, using sweep testing tools or software.
- Install all necessary transmission equipment components, including antennas or antenna mounts, surge arrestors, transmission lines, connectors, or tower-mounted amplifiers (TMAs).
- Read work orders, blueprints, plans, datasheets or site drawings to determine work to be done.
- Replace existing antennas with new antennas as directed.
- Bolt equipment into place, using hand or power tools.
- Install, connect, or test underground or aboveground grounding systems.
- Complete reports related to project status, progress, or other work details, using computer software.
- Check antenna positioning to ensure specified azimuths or mechanical tilts and adjust as necessary.
- Transport equipment to work sites, using utility trucks and equipment trailers.
- Take site survey photos or photos of work performed, using digital cameras.
- Lift equipment into position, using cranes and rigging tools or equipment, such as gin poles.
- Perform maintenance or repair work on existing tower equipment, using hand or power tools.
- Locate tower sites where work is to be performed, using mapping software.
- Install or repair tower lighting components, including strobes, beacons, or lighting controllers.
- Calibrate and align components, using scales, gauges, and other measuring instruments.
- Examine malfunctioning radio equipment to locate defects such as loose connections, broken wires, or burned-out components, using schematic diagrams and test equipment.
- Insert plugs into receptacles and bolt or screw leads to terminals to connect equipment to power sources, using hand tools.
- Install, adjust, and repair stationary and mobile radio transmitting and receiving equipment and two-way radio communication systems.
- Monitor radio range stations to detect transmission flaws and adjust controls to eliminate flaws.
- Mount equipment on transmission towers and in vehicles such as ships or ambulances.
- Remove and replace defective components and parts such as conductors, resistors, semiconductors, and integrated circuits, using soldering irons, wire cutters, and hand tools.
- Repair circuits, wiring, and soldering, using soldering irons and hand tools to install parts and adjust connections.
- Test batteries, using hydrometers and ammeters, and charge batteries as necessary.
- Test emergency transmitters to ensure their readiness for immediate use.
- Test equipment functions such as signal strength and quality, transmission capacity, interference, and signal delay, using equipment such as oscilloscopes, circuit analyzers, frequency meters, and wattmeters.
- Turn setscrews to adjust receivers for maximum sensitivity and transmitters for maximum output.
- Climb towers to access components, using safety equipment, such as full-body harnesses.
- Climb communication towers to install, replace, or repair antennas or auxiliary equipment used to transmit and receive radio waves.
- Climb wind turbine towers to inspect, maintain, or repair equipment.
- Troubleshoot or repair mechanical, hydraulic, or electrical malfunctions related to variable pitch systems, variable speed control systems, converter systems, or related components.
- Perform routine maintenance on wind turbine equipment, underground transmission systems, wind fields substations, or fiber optic sensing and control systems.
- Diagnose problems involving wind turbine generators or control systems.
- Test electrical components of wind systems with devices, such as voltage testers, multimeters, oscilloscopes, infrared testers, or fiber optic equipment.
- Start or restart wind turbine generator systems to ensure proper operations.
- Maintain tool and spare parts inventories required for repair, installation, or replacement services.
- Test structures, controls, or mechanical, hydraulic, or electrical systems, according to test plans or in coordination with engineers.
- Train end-users, distributors, installers, or other technicians in wind commissioning, testing, or other technical procedures.
- Collect turbine data for testing or research and analysis.
- Inspect or repair fiberglass turbine blades.
- Assist in assembly of individual wind generators or construction of wind farms.
- Operate manufacturing equipment to fabricate wind turbines.
- Climb wind turbine towers to inspect, maintain, or repair equipment.
- Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.
- Reline or repair ladles and pouring spouts with refractory clay, using trowels.
- Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.
- Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.
- Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.
- Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.
- Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.
- Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.
- Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.
- Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.
- Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.
- Dump and tamp clay in molds, using tamping tools.
- Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.
- Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.
- Install preformed metal scaffolding in interiors of cupolas, using hand tools.
- Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.
- Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.
- Work on high ceilings, using scaffolding or other tools, such as stilts.
- Spread sealing compound between boards or panels or over cracks, holes, nail heads, or screw heads, using trowels, broadknives, or spatulas.
- Press paper tape over joints to embed tape into sealing compound and to seal joints.
- Apply additional coats to fill in holes and make surfaces smooth.
- Seal joints between plasterboard or other wallboard to prepare wall surfaces for painting or papering.
- Spread and smooth cementing material over tape, using trowels or floating machines to blend joints with wall surfaces.
- Sand or patch nicks or cracks in plasterboard or wallboard.
- Mix sealing compounds by hand or with portable electric mixers.
- Select the correct sealing compound or tape.
- Countersink nails or screws below surfaces of walls before applying sealing compounds, using hammers or screwdrivers.
- Remove extra compound after surfaces have been covered sufficiently.
- Install metal molding at wall corners to secure wallboard.
- Apply texturizing compounds or primers to walls or ceilings before final finishing, using trowels, brushes, rollers, or spray guns.
- Check adhesives to ensure that they will work and will remain durable.
- Sand rough spots of dried cement between applications of compounds.
- Use mechanical applicators that spread compounds and embed tape in one operation.
- Work on high ceilings, using scaffolding or other tools, such as stilts.
- Access specific areas to string lines, or install terminal boxes, auxiliary equipment, or appliances, using bucket trucks, climbing poles or ladders, or entering tunnels, trenches, or crawl spaces.
- Set up service for customers, installing, connecting, testing, or adjusting equipment.
- Travel to customers' premises to install, maintain, or repair audio and visual electronic reception equipment or accessories.
- Measure signal strength at utility poles, using electronic test equipment.
- Inspect or test lines or cables, recording and analyzing test results, to assess transmission characteristics and locate faults or malfunctions.
- Splice cables, using hand tools, epoxy, or mechanical equipment.
- Clean or maintain tools or test equipment.
- String cables between structures and lines from poles, towers, or trenches, and pull lines to proper tension.
- Pull up cable by hand from large reels mounted on trucks.
- Lay underground cable directly in trenches, or string it through conduits running through trenches.
- Pull cable through ducts by hand or with winches.
- Dig trenches for underground wires or cables.
- Explain cable service to subscribers after installation, and collect any installation fees due.
- Place insulation over conductors, or seal splices with moisture-proof covering.
- Compute impedance of wires from poles to houses to determine additional resistance needed for reducing signals to desired levels.
- Install equipment such as amplifiers or repeaters to maintain the strength of communications transmissions.
- Use a variety of construction equipment to complete installations, such as digger derricks, trenchers, or cable plows.
- Fill and tamp holes, using cement, earth, and tamping devices.
- Participate in the construction or removal of telecommunication towers or associated support structures.
- Dig holes for power poles, using power augers or shovels, set poles in place with cranes, and hoist poles upright, using winches.
- Access specific areas to string lines, or install terminal boxes, auxiliary equipment, or appliances, using bucket trucks, climbing poles or ladders, or entering tunnels, trenches, or crawl spaces.
- Climb poles and ladders, use truck-mounted booms, and enter areas such as manholes and cable vaults to install, maintain, or inspect equipment.
- Demonstrate equipment to customers and explain its use, responding to any inquiries or complaints.
- Test circuits and components of malfunctioning telecommunications equipment to isolate sources of malfunctions, using test meters, circuit diagrams, polarity probes, and other hand tools.
- Test repaired, newly installed, or updated equipment to ensure that it functions properly and conforms to specifications, using test equipment and observation.
- Assemble and install communication equipment such as data and telephone communication lines, wiring, switching equipment, wiring frames, power apparatus, computer systems, and networks.
- Run wires between components and to outside cable systems, connecting them to wires from telephone poles or underground cable accesses.
- Test connections to ensure that power supplies are adequate and that communications links function.
- Note differences in wire and cable colors so that work can be performed correctly.
- Inspect equipment on a regular basis to ensure proper functioning.
- Collaborate with other workers to locate and correct malfunctions.
- Remove loose wires and other debris after work is completed.
- Repair or replace faulty equipment, such as defective and damaged telephones, wires, switching system components, and associated equipment.
- Maintain computer and manual records pertaining to facilities and equipment.
- Communicate with bases, using telephones or two-way radios to receive instructions or technical advice, or to report equipment status.
- Remove and remake connections to change circuit layouts, following work orders or diagrams.
- Clean and maintain tools, test equipment, and motor vehicles.
- Perform database verifications, using computers.
- Request support from technical service centers when on-site procedures fail to solve installation or maintenance problems.
- Analyze test readings, computer printouts, and trouble reports to determine equipment repair needs and required repair methods.
- Adjust or modify equipment to enhance equipment performance or to respond to customer requests.
- Remove and replace plug-in circuit equipment.
- Refer to manufacturers' manuals to obtain maintenance instructions pertaining to specific malfunctions.
- Dig holes or trenches as necessary for equipment installation and access.
- Review manufacturer's instructions, manuals, technical specifications, building permits, and ordinances to determine communication equipment requirements and procedures.
- Drive crew trucks to and from work areas.
- Route and connect cables and lines to switches, switchboard equipment, and distributing frames, using wire-wrap guns or soldering irons to connect wires to terminals.
- Designate cables available for use.
- Diagnose and correct problems from remote locations, using special switchboards to find the sources of problems.
- Program computerized switches and switchboards to provide requested features.
- Enter codes needed to correct electronic switching system programming.
- Examine telephone transmission facilities to determine requirements for new or additional telephone services.
- Measure distances from landmarks to identify exact installation sites for equipment.
- Install updated software and programs that maintain existing software or provide requested features, such as time-correlated call routing.
- Perform routine maintenance on equipment, including adjusting and lubricating components and painting worn or exposed areas.
- Determine viability of sites through observation, and discuss site locations and construction requirements with customers.
- Install telephone station equipment, such as intercommunication systems, transmitters, receivers, relays, and ringers, and related apparatus, such as coin collectors, telephone booths, and switching-key equipment.
- Clean switches and replace contact points, using vacuum hoses, solvents, and hand tools.
- Provide input into the design and manufacturing of new equipment.
- Address special issues or situations, such as illegal or unauthorized use of equipment, or cases of electrical or acoustic shock.
- Place intercept circuits on terminals to handle vacant lines in central office installations.
- Climb poles and ladders, use truck-mounted booms, and enter areas such as manholes and cable vaults to install, maintain, or inspect equipment.
