- Scribe and cut edges of tile to fit walls where wall molding is not specified.
Occupations with related tasks Save Table: XLSX CSV
- Shape, trim, face and cut marble or stone preparatory to setting, using power saws, cutting equipment, and hand tools.
- Smooth, polish, and bevel surfaces, using hand tools and power tools.
- Repair cracked or chipped areas of stone or marble, using blowtorch and mastic, and remove rough or defective spots from concrete, using power grinder or chisel and hammer.
- Lay out wall patterns or foundations, using straight edge, rule, or staked lines.
- Set vertical and horizontal alignment of structures, using plumb bob, gauge line, and level.
- Mix mortar or grout and pour or spread mortar or grout on marble slabs, stone, or foundation.
- Remove wedges, fill joints between stones, finish joints between stones, using a trowel, and smooth the mortar to an attractive finish, using a tuck pointer.
- Set stone or marble in place, according to layout or pattern.
- Clean excess mortar or grout from surface of marble, stone, or monument, using sponge, brush, water, or acid.
- Lay brick to build shells of chimneys and smokestacks or to line or reline industrial furnaces, kilns, boilers and similar installations.
- Replace broken or missing masonry units in walls or floors.
- Drill holes in marble or ornamental stone and anchor brackets in holes.
- Remove sections of monument from truck bed, and guide stone onto foundation, using skids, hoist, or truck crane.
- Construct and install prefabricated masonry units.
- Dig trench for foundation of monument, using pick and shovel.
- Position mold along guidelines of wall, press mold in place, and remove mold and paper from wall.
- Line interiors of molds with treated paper and fill molds with composition-stone mixture.
- Shape, trim, face and cut marble or stone preparatory to setting, using power saws, cutting equipment, and hand tools.
- Smooth, polish, and bevel surfaces, using hand tools and power tools.
- Repair cracked or chipped areas of stone or marble, using blowtorch and mastic, and remove rough or defective spots from concrete, using power grinder or chisel and hammer.
- Cut and shape tile to fit around obstacles and into odd spaces and corners, using hand and power cutting tools.
- Cut, surface, polish, and install marble and granite or install pre-cast terrazzo, granite or marble units.
- Measure and cut metal lath to size for walls and ceilings, using tin snips.
- Cut tile backing to required size, using shears.
- Align and straighten tile using levels, squares, and straightedges.
- Finish and dress the joints and wipe excess grout from between tiles, using damp sponge.
- Determine and implement the best layout to achieve a desired pattern.
- Mix, apply, and spread plaster, concrete, mortar, cement, mastic, glue or other adhesives to form a bed for the tiles, using brush, trowel and screed.
- Study blueprints and examine surface to be covered to determine amount of material needed.
- Measure and mark surfaces to be tiled, following blueprints.
- Lay and set mosaic tiles to create decorative wall, mural, and floor designs.
- Apply mortar to tile back, position the tile, and press or tap with trowel handle to affix tile to base.
- Mix and apply mortar or cement to edges and ends of drain tiles to seal halves and joints.
- Apply a sealer to make grout stain- and water-resistant.
- Level concrete and allow to dry.
- Install and anchor fixtures in designated positions, using hand tools.
- Prepare surfaces for tiling by attaching lath or waterproof paper, or by applying a cement mortar coat to a metal screen.
- Remove and replace cracked or damaged tile.
- Remove any old tile, grout and adhesive using chisels and scrapers and clean the surface carefully.
- Spread mastic or other adhesive base on roof deck to form base for promenade tile, using serrated spreader.
- Assist customers in selection of tile and grout.
- Prepare cost and labor estimates, based on calculations of time and materials needed for project.
- Brush glue onto manila paper on which design has been drawn and position tiles, finished side down, onto paper.
- Select and order tile and other items to be installed, such as bathroom accessories, walls, panels, and cabinets, according to specifications.
- Build underbeds and install anchor bolts, wires, and brackets.
- Cut and shape tile to fit around obstacles and into odd spaces and corners, using hand and power cutting tools.
- Cut, surface, polish, and install marble and granite or install pre-cast terrazzo, granite or marble units.
- Measure and cut metal lath to size for walls and ceilings, using tin snips.
- Cut tile backing to required size, using shears.
- Cut slabs of stone into sheets that will be used for floors or counters.
- Cut grooves along outlines, using chisels.
- Locate grain line patterns to determine how rocks will split when cut.
- Remove pieces of stone from larger masses, using jackhammers, wedges, and other tools.
- Insert wedges and feathers into holes, and drive wedges with sledgehammers to split stone sections from masses.
- Mark dimensions or outlines on stone prior to cutting, using rules and chalk lines.
- Set charges of explosives to split rock.
- Drill holes along outlines, using jackhammers.
- Drill holes into sides of stones broken from masses, insert dogs or attach slings, and direct removal of stones.
- Cut slabs of stone into sheets that will be used for floors or counters.
- Cut grooves along outlines, using chisels.
- Cut paving stones to size and for edges, using a splitter and a masonry saw.
- Prepare base for installation by removing unstable or unsuitable materials, compacting and grading the soil, draining or stabilizing weak or saturated soils and taking measures to prevent water penetration and migration of bedding sand.
- Supply and place base materials, edge restraints, bedding sand and jointing sand.
- Discuss the design with the client.
- Set pavers, aligning and spacing them correctly.
- Sweep sand into the joints and compact pavement until the joints are full.
- Screed sand level to an even thickness, and recheck sand exposed to elements, raking and rescreeding if necessary.
- Compact bedding sand and pavers to finish the paved area, using a plate compactor.
- Design paver installation layout pattern and create markings for directional references of joints and stringlines.
- Sweep sand from the surface prior to opening to traffic.
- Resurface an outside area with cobblestones, terracotta tiles, concrete or other materials.
- Cement the edges of the paved area.
- Cut paving stones to size and for edges, using a splitter and a masonry saw.
- Break or cut bricks, tiles, or blocks to size, using trowel edge, hammer, or power saw.
- Measure distance from reference points and mark guidelines to lay out work, using plumb bobs and levels.
- Construct corners by fastening in plumb position a corner pole or building a corner pyramid of bricks, and filling in between the corners using a line from corner to corner to guide each course, or layer, of brick.
- Apply and smooth mortar or other mixture over work surface.
- Calculate angles and courses and determine vertical and horizontal alignment of courses.
- Interpret blueprints and drawings to determine specifications and to calculate the materials required.
- Remove excess mortar with trowels and hand tools, and finish mortar joints with jointing tools, for a sealed, uniform appearance.
- Fasten or fuse brick or other building material to structure with wire clamps, anchor holes, torch, or cement.
- Clean working surface to remove scale, dust, soot, or chips of brick and mortar, using broom, wire brush, or scraper.
- Examine brickwork or structure to determine need for repair.
- Mix specified amounts of sand, clay, dirt, or mortar powder with water to form refractory mixtures.
- Remove burned or damaged brick or mortar, using sledgehammer, crowbar, chipping gun, or chisel.
- Lay and align bricks, blocks, or tiles to build or repair structures or high temperature equipment, such as cupola, kilns, ovens, or furnaces.
- Spray or spread refractory material over brickwork to protect against deterioration.
- Break or cut bricks, tiles, or blocks to size, using trowel edge, hammer, or power saw.
- Cut materials to specified sizes for installation, using power saws or tile cutters.
- Mix mortar, plaster, and grout, manually or using machines, according to standard formulas.
- Erect scaffolding or other installation structures.
- Modify material moving, mixing, grouting, grinding, polishing, or cleaning procedures, according to installation or material requirements.
- Transport materials, tools, or machines to installation sites, manually or using conveyance equipment.
- Provide assistance in the preparation, installation, repair, or rebuilding of tile, brick, or stone surfaces.
- Locate and supply materials to masons for installation, following drawings or numbered sequences.
- Arrange or store materials, machines, tools, or equipment.
- Clean installation surfaces, equipment, tools, work sites, or storage areas, using water, chemical solutions, oxygen lances, or polishing machines.
- Move or position materials such as marble slabs, using cranes, hoists, or dollies.
- Remove excess grout or residue from tile or brick joints, using sponges or trowels.
- Apply grout between joints of bricks or tiles, using grouting trowels.
- Apply caulk, sealants, or other agents to installed surfaces.
- Remove damaged tile, brick, or mortar, and clean or prepare surfaces, using pliers, hammers, chisels, drills, wire brushes, or metal wire anchors.
- Correct surface imperfections or fill chipped, cracked, or broken bricks or tiles, using fillers, adhesives, or grouting materials.
- Cut materials to specified sizes for installation, using power saws or tile cutters.
- Operate machines that clean or cut expansion joints in concrete or asphalt and that rout out cracks in pavement.
- Start machine, engage clutch, and push and move levers to guide machine along forms or guidelines and to control the operation of machine attachments.
- Fill tanks, hoppers, or machines with paving materials.
- Control paving machines to push dump trucks and to maintain a constant flow of asphalt or other material into hoppers or screeds.
- Observe distribution of paving material to adjust machine settings or material flow, and indicate low spots for workers to add material.
- Coordinate truck dumping.
- Drive machines onto truck trailers, and drive trucks to transport machines and material to and from job sites.
- Inspect, clean, maintain, and repair equipment, using mechanics' hand tools, or report malfunctions to supervisors.
- Set up and tear down equipment.
- Operate machines to spread, smooth, level, or steel-reinforce stone, concrete, or asphalt on road beds.
- Light burners or start heating units of machines, and regulate screed temperatures and asphalt flow rates.
- Control traffic.
- Shovel blacktop.
- Operate tamping machines or manually roll surfaces to compact earth fills, foundation forms, and finished road materials, according to grade specifications.
- Operate oil distributors, loaders, chip spreaders, dump trucks, and snow plows.
- Place strips of material, such as cork, asphalt, or steel into joints, or place rolls of expansion-joint material on machines that automatically insert material.
- Drive and operate curbing machines to extrude concrete or asphalt curbing.
- Cut or break up pavement and drive guardrail posts, using machines equipped with interchangeable hammers.
- Install dies, cutters, and extensions to screeds onto machines, using hand tools.
- Set up forms and lay out guidelines for curbs, according to written specifications, using string, spray paint, and concrete or water mixes.
- Operate machines that clean or cut expansion joints in concrete or asphalt and that rout out cracks in pavement.
