- Assemble prototypes or models of circuits, instruments, and systems for use in testing.
Occupations with related tasks Save Table: XLSX CSV
- Set in and secure floor treadles for door-activating mechanisms, and connect power packs and electrical panelboards to treadles.
- Wind large springs with upward motion of arm.
- Fasten angle iron back-hangers to ceilings and tracks, using fasteners or welding equipment.
- Adjust doors to open or close with the correct amount of effort, or make simple adjustments to electric openers.
- Carry springs to tops of doors, using ladders or scaffolding, and attach springs to tracks to install spring systems.
- Repair or replace worn or broken door parts, using hand tools.
- Complete required paperwork, such as work orders, according to services performed or required.
- Collect payment upon job completion.
- Install door frames, rails, steel rolling curtains, electronic-eye mechanisms, or electric door openers and closers, using power tools, hand tools, and electronic test equipment.
- Inspect job sites, assessing headroom, side room, or other conditions to determine appropriateness of door for a given location.
- Assemble and fasten tracks to structures or bucks, using impact wrenches or welding equipment.
- Set doors into place or stack hardware sections into openings after rail or track installation.
- Operate lifts, winches, or chain falls to move heavy curtain doors.
- Remove or disassemble defective automatic mechanical door closers, using hand tools.
- Fabricate replacements for worn or broken parts, using welders, lathes, drill presses, or shaping or milling machines.
- Prepare doors for hardware installation, such as drilling holes to install locks.
- Run low voltage wiring on ceiling surfaces, using insulated staples.
- Cut door stops or angle irons to fit openings.
- Study blueprints and schematic diagrams to determine appropriate methods of installing or repairing automated door openers.
- Install dock seals, bumpers, or shelters.
- Order replacement springs, sections, or slats.
- Lubricate door closer oil chambers, and pack spindles with leather washers.
- Cover treadles with carpeting or other floor covering materials, and test systems by operating treadles.
- Bore or cut holes in flooring as required for installation, using hand or power tools.
- Clean door closer parts, using caustic soda, rotary brushes, or grinding wheels.
- Set in and secure floor treadles for door-activating mechanisms, and connect power packs and electrical panelboards to treadles.
- Wind large springs with upward motion of arm.
- Fasten angle iron back-hangers to ceilings and tracks, using fasteners or welding equipment.
- Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.
- Perform routine maintenance on boilers, such as replacing burners or hoses, installing replacement parts, or reinforcing structural weaknesses to ensure optimal boiler efficiency.
- Assemble boilers at installation sites, using tools such as levels, plumb bobs, hammers, torches, or other hand tools.
- Perform routine maintenance, such as inspecting drives, motors, or belts, checking fluid levels, replacing filters, or doing other preventive maintenance actions.
- Inspect, operate, or test machinery or equipment to diagnose machine malfunctions.
- Adjust functional parts of devices or control instruments, using hand tools, levels, plumb bobs, or straightedges.
- Order parts, supplies, or equipment from catalogs or suppliers.
- Diagnose mechanical problems and determine how to correct them, checking blueprints, repair manuals, or parts catalogs, as necessary.
- Design new equipment to aid in the repair or maintenance of machines, mechanical equipment, or building structures.
- Clean or lubricate shafts, bearings, gears, or other parts of machinery.
- Estimate costs to repair machinery, equipment, or building structures.
- Align and balance new equipment after installation.
- Record type and cost of maintenance or repair work.
- Maintain or repair specialized equipment or machinery located in cafeterias, laundries, hospitals, stores, offices, or factories.
- Dismantle machines, equipment, or devices to access and remove defective parts, using hoists, cranes, hand tools, or power tools.
- Plan and lay out repair work, using diagrams, drawings, blueprints, maintenance manuals, or schematic diagrams.
- Install equipment to improve the energy or operational efficiency of residential or commercial buildings.
- Set up and operate machine tools to repair or fabricate machine parts, jigs, fixtures, or tools.
- Perform general cleaning of buildings or properties.
- Train or manage maintenance personnel or subcontractors.
- Fabricate or repair counters, benches, partitions, or other wooden structures, such as sheds or outbuildings.
- Paint or repair roofs, windows, doors, floors, woodwork, plaster, drywall, or other parts of building structures.
- Test and treat water supply.
- Provide groundskeeping services, such as landscaping or snow removal.
- Operate cutting torches or welding equipment to cut or join metal parts.
- Inspect used parts to determine changes in dimensional requirements, using rules, calipers, micrometers, or other measuring instruments.
- Lay brick to repair or maintain buildings, walls, arches, or other structures.
- Position, attach, or blow insulating materials to prevent energy losses from buildings, pipes, or other structures or objects.
- Grind and reseat valves, using valve-grinding machines.
- Repair machines, equipment, or structures, using tools such as hammers, hoists, saws, drills, wrenches, or equipment such as precision measuring instruments or electrical or electronic testing devices.
- Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.
- Perform routine maintenance on boilers, such as replacing burners or hoses, installing replacement parts, or reinforcing structural weaknesses to ensure optimal boiler efficiency.
- Assemble boilers at installation sites, using tools such as levels, plumb bobs, hammers, torches, or other hand tools.
- Assemble and install electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools.
- Reassemble engines following repair or inspection and reinstall engines in aircraft.
- Install and align repaired or replacement parts for subsequent riveting or welding, using clamps and wrenches.
- Examine and inspect aircraft components, including landing gear, hydraulic systems, and deicers to locate cracks, breaks, leaks, or other problems.
- Conduct routine and special inspections as required by regulations.
- Inspect completed work to certify that maintenance meets standards and that aircraft are ready for operation.
- Read and interpret maintenance manuals, service bulletins, and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.
- Maintain repair logs, documenting all preventive and corrective aircraft maintenance.
- Modify aircraft structures, space vehicles, systems, or components, following drawings, schematics, charts, engineering orders, and technical publications.
- Inspect airframes for wear or other defects.
- Measure parts for wear, using precision instruments.
- Obtain fuel and oil samples and check them for contamination.
- Maintain, repair, and rebuild aircraft structures, functional components, and parts, such as wings and fuselage, rigging, hydraulic units, oxygen systems, fuel systems, electrical systems, gaskets, or seals.
- Replace or repair worn, defective, or damaged components, using hand tools, gauges, and testing equipment.
- Read and interpret pilots' descriptions of problems to diagnose causes.
- Test operation of engines and other systems, using test equipment, such as ignition analyzers, compression checkers, distributor timers, or ammeters.
- Measure the tension of control cables.
- Spread plastic film over areas to be repaired to prevent damage to surrounding areas.
- Remove or install aircraft engines, using hoists or forklift trucks.
- Locate and mark dimensions and reference lines on defective or replacement parts, using templates, scribes, compasses, and steel rules.
- Fabricate defective sections or parts, using metal fabricating machines, saws, brakes, shears, and grinders.
- Service and maintain aircraft and related apparatus by performing activities such as flushing crankcases, cleaning screens, and or moving parts.
- Clean, refuel, and change oil in line service aircraft.
- Trim and shape replacement body sections to specified sizes and fits and secure sections in place, using adhesives, hand tools, and power tools.
- Accompany aircraft on flights to make in-flight adjustments and corrections.
- Remove or cut out defective parts or drill holes to gain access to internal defects or damage, using drills and punches.
- Inventory and requisition or order supplies, parts, materials, and equipment.
- Clean, strip, prime, and sand structural surfaces and materials to prepare them for bonding.
- Communicate with other workers to coordinate fitting and alignment of heavy parts, or to facilitate processing of repair parts.
- Examine engines through specially designed openings while working from ladders or scaffolds, or use hoists or lifts to remove the entire engine from an aircraft.
- Check for corrosion, distortion, and invisible cracks in the fuselage, wings, and tail, using x-ray and magnetic inspection equipment.
- Disassemble engines and inspect parts, such as turbine blades or cylinders, for corrosion, wear, warping, cracks, and leaks, using precision measuring instruments, x-rays, and magnetic inspection equipment.
- Cure bonded structures, using portable or stationary curing equipment.
- Listen to operating engines to detect and diagnose malfunctions, such as sticking or burned valves.
- Clean engines, sediment bulk and screens, and carburetors, adjusting carburetor float levels.
- Determine repair limits for engine hot section parts.
- Remove, inspect, repair, and install in-flight refueling stores and external fuel tanks.
- Prepare and paint aircraft surfaces.
- Assemble and install electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools.
- Reassemble engines following repair or inspection and reinstall engines in aircraft.
- Install and align repaired or replacement parts for subsequent riveting or welding, using clamps and wrenches.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Bolt porcelain insulators to wood parts to assemble hot stools.
- Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
- Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Lift units or parts such as motors or generators, using cranes or chain hoists, or signal crane operators to lift heavy parts or subassemblies.
- Record repairs required, parts used, and labor time.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Lubricate moving parts.
- Read service guides to find information needed to perform repairs.
- Inspect electrical connections, wiring, relays, charging resistance boxes, and storage batteries, following wiring diagrams.
- Scrape and clean units or parts, using cleaning solvents and equipment such as buffing wheels.
- Weld, braze, or solder electrical connections.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Steam-clean polishing and buffing wheels to remove abrasives and bonding materials, and spray, brush, or recoat surfaces as necessary.
- Set machinery for proper performance, using computers.
- Test equipment for overheating, using speed gauges and thermometers.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Maintain stocks of parts.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Solder, wrap, and coat wires to ensure proper insulation.
- Rewire electrical systems, and repair or replace electrical accessories.
- Clean cells, cell assemblies, glassware, leads, electrical connections, and battery poles, using scrapers, steam, water, emery cloths, power grinders, or acid.
- Rewind coils on cores in slots, or make replacement coils, using coil-winding machines.
- Test conditions, fluid levels, and specific gravities of electrolyte cells, using voltmeters, hydrometers, and thermometers.
- Add water or acid to battery cell solutions to obtain specified concentrations.
- Pour compounds into transformer-case terminal openings to seal out moisture.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Hammer out dents and twists in tools and equipment.
- Drain and filter transformer oil and refill transformers with oil until coils are submerged.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Repair and operate battery-charging equipment.
- Sharpen tools such as saws, picks, shovels, screwdrivers, and scoops, either manually or by using bench grinders and emery wheels.
- Inspect batteries for structural defects such as dented cans, damaged carbon rods and terminals, and defective seals.
- Test battery charges, and replace or recharge batteries as necessary.
- Position and level battery cells, anodes, or cathodes, using hoists or leveling jacks, or signal other workers to perform positioning and leveling.
- Clean, rinse, and dry transformer cases, using boiling water, scrapers, solvents, hoses, and cloths.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Bolt porcelain insulators to wood parts to assemble hot stools.
- Install, maintain, and repair electrical distribution and transmission systems, including conduits, cables, wires, and related equipment, such as transformers, circuit breakers, and switches.
- Attach cross-arms, insulators, and auxiliary equipment to poles prior to installing them.
- Adhere to safety practices and procedures, such as checking equipment regularly and erecting barriers around work areas.
- Drive vehicles equipped with tools and materials to job sites.
- Open switches or attach grounding devices to remove electrical hazards from disturbed or fallen lines or to facilitate repairs.
- Climb poles or use truck-mounted buckets to access equipment.
- Inspect and test power lines and auxiliary equipment to locate and identify problems, using reading and testing instruments.
- Coordinate work assignment preparation and completion with other workers.
- Replace or straighten damaged poles.
- String wire conductors and cables between poles, towers, trenches, pylons, and buildings, setting lines in place and using winches to adjust tension.
- Dig holes, using augers, and set poles, using cranes and power equipment.
- Travel in trucks, helicopters, and airplanes to inspect lines for freedom from obstruction and adequacy of insulation.
- Identify defective sectionalizing devices, circuit breakers, fuses, voltage regulators, transformers, switches, relays, or wiring, using wiring diagrams and electrical-testing instruments.
- Install watt-hour meters and connect service drops between power lines and consumers' facilities.
- Test conductors, according to electrical diagrams and specifications, to identify corresponding conductors and to prevent incorrect connections.
- Place insulating or fireproofing materials over conductors and joints.
- Splice or solder cables together or to overhead transmission lines, customer service lines, or street light lines, using hand tools, epoxies, or specialized equipment.
- Trim trees that could be hazardous to the functioning of cables or wires.
- Pull up cable by hand from large reels mounted on trucks.
- Lay underground cable directly in trenches, or string it through conduit running through the trenches.
- Cut trenches for laying underground cables, using trenchers and cable plows.
- Cut and peel lead sheathing and insulation from defective or newly installed cables and conduits prior to splicing.
- Clean, tin, and splice corresponding conductors by twisting ends together or by joining ends with metal clamps and soldering connections.
- Install, maintain, and repair electrical distribution and transmission systems, including conduits, cables, wires, and related equipment, such as transformers, circuit breakers, and switches.
- Attach cross-arms, insulators, and auxiliary equipment to poles prior to installing them.
- Install, connect, or test underground or aboveground grounding systems.
- Bolt equipment into place, using hand or power tools.
- Inspect completed work to ensure all hardware is tight, antennas are level, hangers are properly fastened, proper support is in place, or adequate weather proofing has been installed.
- Run appropriate power, ground, or coaxial cables.
- Test operation of tower transmission components, using sweep testing tools or software.
- Install all necessary transmission equipment components, including antennas or antenna mounts, surge arrestors, transmission lines, connectors, or tower-mounted amplifiers (TMAs).
- Read work orders, blueprints, plans, datasheets or site drawings to determine work to be done.
- Replace existing antennas with new antennas as directed.
- Complete reports related to project status, progress, or other work details, using computer software.
- Check antenna positioning to ensure specified azimuths or mechanical tilts and adjust as necessary.
- Transport equipment to work sites, using utility trucks and equipment trailers.
- Take site survey photos or photos of work performed, using digital cameras.
- Climb towers to access components, using safety equipment, such as full-body harnesses.
- Climb communication towers to install, replace, or repair antennas or auxiliary equipment used to transmit and receive radio waves.
- Lift equipment into position, using cranes and rigging tools or equipment, such as gin poles.
- Perform maintenance or repair work on existing tower equipment, using hand or power tools.
- Locate tower sites where work is to be performed, using mapping software.
- Install or repair tower lighting components, including strobes, beacons, or lighting controllers.
- Calibrate and align components, using scales, gauges, and other measuring instruments.
- Examine malfunctioning radio equipment to locate defects such as loose connections, broken wires, or burned-out components, using schematic diagrams and test equipment.
- Insert plugs into receptacles and bolt or screw leads to terminals to connect equipment to power sources, using hand tools.
- Install, adjust, and repair stationary and mobile radio transmitting and receiving equipment and two-way radio communication systems.
- Monitor radio range stations to detect transmission flaws and adjust controls to eliminate flaws.
- Mount equipment on transmission towers and in vehicles such as ships or ambulances.
- Remove and replace defective components and parts such as conductors, resistors, semiconductors, and integrated circuits, using soldering irons, wire cutters, and hand tools.
- Repair circuits, wiring, and soldering, using soldering irons and hand tools to install parts and adjust connections.
- Test batteries, using hydrometers and ammeters, and charge batteries as necessary.
- Test emergency transmitters to ensure their readiness for immediate use.
- Test equipment functions such as signal strength and quality, transmission capacity, interference, and signal delay, using equipment such as oscilloscopes, circuit analyzers, frequency meters, and wattmeters.
- Turn setscrews to adjust receivers for maximum sensitivity and transmitters for maximum output.
- Install, connect, or test underground or aboveground grounding systems.
- Bolt equipment into place, using hand or power tools.
- Install alarm and electronic access systems.
- Cut new or duplicate keys, using key cutting machines.
- Disassemble mechanical or electrical locking devices, and repair or replace worn tumblers, springs, and other parts, using hand tools.
- Cut new or duplicate keys, using impressions or code key machines.
- Open safe locks by drilling.
- Install door hardware, such as locks and closers.
- Insert new or repaired tumblers into locks to change combinations.
- Set up and maintain master key systems.
- Keep records of company locks and keys.
- Move picklocks in cylinders to open door locks without keys.
- Repair and adjust safes, vault doors, and vault components, using hand tools, lathes, drill presses, and welding and acetylene cutting apparatus.
- Install safes, vault doors, and deposit boxes according to blueprints, using equipment such as power drills, taps, dies, truck cranes, and dollies.
- Unlock cars and other vehicles.
- Remove interior and exterior finishes on safes and vaults, and spray on new finishes.
- Install alarm and electronic access systems.
- Assemble and install communication equipment such as data and telephone communication lines, wiring, switching equipment, wiring frames, power apparatus, computer systems, and networks.
- Demonstrate equipment to customers and explain its use, responding to any inquiries or complaints.
- Test circuits and components of malfunctioning telecommunications equipment to isolate sources of malfunctions, using test meters, circuit diagrams, polarity probes, and other hand tools.
- Test repaired, newly installed, or updated equipment to ensure that it functions properly and conforms to specifications, using test equipment and observation.
- Climb poles and ladders, use truck-mounted booms, and enter areas such as manholes and cable vaults to install, maintain, or inspect equipment.
- Run wires between components and to outside cable systems, connecting them to wires from telephone poles or underground cable accesses.
- Test connections to ensure that power supplies are adequate and that communications links function.
- Note differences in wire and cable colors so that work can be performed correctly.
- Inspect equipment on a regular basis to ensure proper functioning.
- Collaborate with other workers to locate and correct malfunctions.
- Remove loose wires and other debris after work is completed.
- Repair or replace faulty equipment, such as defective and damaged telephones, wires, switching system components, and associated equipment.
- Maintain computer and manual records pertaining to facilities and equipment.
- Communicate with bases, using telephones or two-way radios to receive instructions or technical advice, or to report equipment status.
- Remove and remake connections to change circuit layouts, following work orders or diagrams.
- Clean and maintain tools, test equipment, and motor vehicles.
- Perform database verifications, using computers.
- Request support from technical service centers when on-site procedures fail to solve installation or maintenance problems.
- Analyze test readings, computer printouts, and trouble reports to determine equipment repair needs and required repair methods.
- Adjust or modify equipment to enhance equipment performance or to respond to customer requests.
- Remove and replace plug-in circuit equipment.
- Refer to manufacturers' manuals to obtain maintenance instructions pertaining to specific malfunctions.
- Dig holes or trenches as necessary for equipment installation and access.
- Review manufacturer's instructions, manuals, technical specifications, building permits, and ordinances to determine communication equipment requirements and procedures.
- Drive crew trucks to and from work areas.
- Route and connect cables and lines to switches, switchboard equipment, and distributing frames, using wire-wrap guns or soldering irons to connect wires to terminals.
- Designate cables available for use.
- Diagnose and correct problems from remote locations, using special switchboards to find the sources of problems.
- Program computerized switches and switchboards to provide requested features.
- Enter codes needed to correct electronic switching system programming.
- Examine telephone transmission facilities to determine requirements for new or additional telephone services.
- Measure distances from landmarks to identify exact installation sites for equipment.
- Install updated software and programs that maintain existing software or provide requested features, such as time-correlated call routing.
- Perform routine maintenance on equipment, including adjusting and lubricating components and painting worn or exposed areas.
- Determine viability of sites through observation, and discuss site locations and construction requirements with customers.
- Install telephone station equipment, such as intercommunication systems, transmitters, receivers, relays, and ringers, and related apparatus, such as coin collectors, telephone booths, and switching-key equipment.
- Clean switches and replace contact points, using vacuum hoses, solvents, and hand tools.
- Provide input into the design and manufacturing of new equipment.
- Address special issues or situations, such as illegal or unauthorized use of equipment, or cases of electrical or acoustic shock.
- Place intercept circuits on terminals to handle vacant lines in central office installations.
- Assemble and install communication equipment such as data and telephone communication lines, wiring, switching equipment, wiring frames, power apparatus, computer systems, and networks.
