- Repair window sash frames, attach weather stripping and channels to frames, and replace window glass, using hand tools.
Occupations with related tasks Save Table: XLSX CSV
- Prime all scratches on pinchwelds with primer and allow to dry.
- Remove all dirt, foreign matter, and loose glass from damaged areas, apply primer along windshield or window edges, and allow primer to dry.
- Allow all glass parts installed with urethane ample time to cure, taking temperature and humidity into account.
- Apply a bead of urethane around the perimeter of each pinchweld and dress the remaining urethane on the pinchwelds so that it is of uniform level and thickness.
- Install replacement glass in vehicles.
- Remove broken or damaged glass windshields or window glass from motor vehicles, using hand tools to remove screws from frames holding glass.
- Install, repair, or replace safety glass and related materials, such as back glass heating elements, on vehicles or equipment.
- Replace or adjust motorized or manual window-raising mechanisms.
- Install rubber channeling strips around edges of glass or frames to weatherproof windows or to prevent rattling.
- Select appropriate tools, safety equipment, and parts, according to job requirements.
- Obtain windshields or windows for specific automobile makes and models from stock and examine them for defects prior to installation.
- Check for and remove moisture or contamination in damaged areas and keep areas dry until repairs are complete.
- Replace all moldings, clips, windshield wipers, or other parts that were removed prior to glass replacement or repair.
- Remove moldings, clips, windshield wipers, screws, bolts, and inside A-pillar moldings and lower headliners in preparation for installation or repair work.
- Cool or warm glass in the event of temperature extremes.
- Install new foam dams on pinchwelds, if required.
- Hold cut or uneven edges of glass against automated abrasive belts to shape or smooth edges.
- Cut flat safety glass according to specified patterns or perform precision pattern making and glass cutting to custom fit replacement windows.
- Prime all scratches on pinchwelds with primer and allow to dry.
- Remove all dirt, foreign matter, and loose glass from damaged areas, apply primer along windshield or window edges, and allow primer to dry.
- Allow all glass parts installed with urethane ample time to cure, taking temperature and humidity into account.
- Apply a bead of urethane around the perimeter of each pinchweld and dress the remaining urethane on the pinchwelds so that it is of uniform level and thickness.
- Install replacement glass in vehicles.
- Remove broken or damaged glass windshields or window glass from motor vehicles, using hand tools to remove screws from frames holding glass.
- Install, repair, or replace safety glass and related materials, such as back glass heating elements, on vehicles or equipment.
- Replace or adjust motorized or manual window-raising mechanisms.
- Install rubber channeling strips around edges of glass or frames to weatherproof windows or to prevent rattling.
- Diagnose and repair vehicle heating and cooling systems.
- Inspect, repair, and maintain automotive and mechanical equipment and machinery, such as pumps and compressors.
- Install or repair accessories.
- Repair or adjust seats, doors, or windows.
- Disassemble and overhaul internal combustion engines, pumps, generators, transmissions, clutches, and differential units.
- Rebuild gas or diesel engines.
- Specialize in repairing and maintaining parts of the engine, such as fuel injection systems.
- Recondition and replace parts, pistons, bearings, gears, and valves.
- Dismount, mount, and repair or replace tires.
- Use handtools, such as screwdrivers, pliers, wrenches, pressure gauges, or precision instruments, as well as power tools, such as pneumatic wrenches, lathes, welding equipment, or jacks and hoists.
- Inspect brake systems, steering mechanisms, wheel bearings, and other important parts to ensure that they are in proper operating condition.
- Raise trucks, buses, and heavy parts or equipment using hydraulic jacks or hoists.
- Adjust and reline brakes, align wheels, tighten bolts and screws, and reassemble equipment.
- Attach test instruments to equipment, and read dials and gauges to diagnose malfunctions.
- Perform routine maintenance such as changing oil, checking batteries, and lubricating equipment and machinery.
- Examine and adjust protective guards, loose bolts, and specified safety devices.
- Inspect, test, and listen to defective equipment to diagnose malfunctions, using test instruments such as handheld computers, motor analyzers, chassis charts, or pressure gauges.
- Rewire ignition systems, lights, and instrument panels.
- Test drive trucks and buses to diagnose malfunctions or to ensure that they are working properly.
- Inspect and verify dimensions and clearances of parts to ensure conformance to factory specifications.
- Adjust or repair computer controlled exhaust emissions devices.
- Align front ends and suspension systems.
- Maintain or repair vehicles with alternative fuel systems, including biodiesel, hybrid, or compressed natural gas vehicles.
- Measure vehicle emissions to determine whether they are within acceptable limits.
- Follow green operational practices involving conservation of water or energy or reduction of solid waste.
- Operate valve-grinding machines to grind and reset valves.
- Diagnose and repair vehicle heating and cooling systems.
- Inspect, repair, and maintain automotive and mechanical equipment and machinery, such as pumps and compressors.
- Install or repair accessories.
- Repair or adjust seats, doors, or windows.
- Disassemble and overhaul internal combustion engines, pumps, generators, transmissions, clutches, and differential units.
- Rebuild gas or diesel engines.
- Specialize in repairing and maintaining parts of the engine, such as fuel injection systems.
- Recondition and replace parts, pistons, bearings, gears, and valves.
- Dismount, mount, and repair or replace tires.
- Repair, reline, replace, and adjust brakes.
- Tear down, repair, and rebuild faulty assemblies, such as power systems, steering systems, and linkages.
- Repair or replace parts such as pistons, rods, gears, valves, and bearings.
- Install, adjust, or repair hydraulic or electromagnetic automatic lift mechanisms used to raise and lower automobile windows, seats, and tops.
- Repair, replace, or adjust defective fuel injectors, carburetor parts, and gasoline filters.
- Rebuild parts, such as crankshafts and cylinder blocks.
- Inspect vehicles for damage and record findings so that necessary repairs can be made.
- Test drive vehicles and test components and systems, using equipment such as infrared engine analyzers, compression gauges, and computerized diagnostic devices.
- Test and adjust repaired systems to meet manufacturers' performance specifications.
- Review work orders and discuss work with supervisors.
- Estimate costs of vehicle repair.
- Confer with customers to obtain descriptions of vehicle problems and to discuss work to be performed and future repair requirements.
- Align vehicles' front ends.
- Align wheels, axles, frames, torsion bars, and steering mechanisms of automobiles, using special alignment equipment and wheel-balancing machines.
- Perform routine and scheduled maintenance services, such as oil changes, lubrications, and tune-ups.
- Plan work procedures, using charts, technical manuals, and experience.
- Follow checklists to ensure all important parts are examined, including belts, hoses, steering systems, spark plugs, brake and fuel systems, wheel bearings, and other potentially troublesome areas.
- Maintain cleanliness of work area.
- Change spark plugs, fuel filters, air filters, and batteries in hybrid electric vehicles.
- Repair and service air conditioning, heating, engine cooling, and electrical systems.
- Disassemble units and inspect parts for wear, using micrometers, calipers, and gauges.
- Test electronic computer components in automobiles to ensure proper operation.
- Overhaul or replace carburetors, blowers, generators, distributors, starters, and pumps.
- Rewire ignition systems, lights, and instrument panels.
- Troubleshoot fuel, ignition, and emissions control systems, using electronic testing equipment.
- Tune automobile engines to ensure proper and efficient functioning.
- Conduct visual inspections of compressed natural gas fuel systems to identify cracks, gouges, abrasions, discoloration, broken fibers, loose brackets, damaged gaskets, or other problems.
- Diagnose and replace or repair engine management systems or related sensors for flexible fuel vehicles (FFVs) with ignition timing, fuel rate, alcohol concentration, or air-to-fuel ratio malfunctions.
- Repair or rebuild transmissions.
- Retrofit vehicle fuel systems with aftermarket products, such as vapor transfer devices, evaporation control devices, swirlers, lean burn devices, and friction reduction devices, to enhance combustion and fuel efficiency.
- Repair, reline, replace, and adjust brakes.
- Tear down, repair, and rebuild faulty assemblies, such as power systems, steering systems, and linkages.
- Repair or replace parts such as pistons, rods, gears, valves, and bearings.
- Install, adjust, or repair hydraulic or electromagnetic automatic lift mechanisms used to raise and lower automobile windows, seats, and tops.
- Repair, replace, or adjust defective fuel injectors, carburetor parts, and gasoline filters.
- Rebuild parts, such as crankshafts and cylinder blocks.
- Replace defective parts, using hand tools, arbor presses, flexible power presses, or power tools.
- Repair or replace other parts, such as headlights, horns, handlebar controls, gasoline or oil tanks, starters, or mufflers.
- Repair or adjust motorcycle subassemblies, such as forks, transmissions, brakes, or drive chains, according to specifications.
- Dismantle engines and repair or replace defective parts, such as magnetos, carburetors, or generators.
- Mount, balance, change, or check condition or pressure of tires.
- Connect test panels to engines and measure generator output, ignition timing, or other engine performance indicators.
- Listen to engines, examine vehicle frames, or confer with customers to determine nature and extent of malfunction or damage.
- Disassemble subassembly units and examine condition, movement, or alignment of parts, visually or using gauges.
- Reassemble frames and reinstall engines after repairs.
- Remove cylinder heads and grind valves to scrape off carbon and replace defective valves, pistons, cylinders, or rings, using hand and power tools.
- Install motorcycle accessories.
- Reassemble and test subassembly units.
- Hammer out dents and bends in frames and weld tears and breaks.
- Replace defective parts, using hand tools, arbor presses, flexible power presses, or power tools.
- Repair or replace other parts, such as headlights, horns, handlebar controls, gasoline or oil tanks, starters, or mufflers.
- Repair or adjust motorcycle subassemblies, such as forks, transmissions, brakes, or drive chains, according to specifications.
- Dismantle engines and repair or replace defective parts, such as magnetos, carburetors, or generators.
- Remove damaged exterior panels, and repair and replace structural frame members.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Inspect recreational vehicles to diagnose problems and perform necessary adjustment, repair, or overhaul.
- Explain proper operation of vehicle systems to customers.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, or hand tools.
- Repair plumbing or propane gas lines, using caulking compounds and plastic or copper pipe.
- Confer with customers, read work orders, or examine vehicles needing repair to determine the nature and extent of damage.
- Examine or test operation of parts or systems to ensure completeness of repairs.
- Connect electrical systems to outside power sources, and activate switches to test the operation of appliances or light fixtures.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of toilets or sinks.
- Inspect, repair, or replace brake systems.
- Diagnose and repair furnace or air conditioning systems.
- Repair leaks with caulking compound or replace pipes, using pipe wrenches.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, or diagrams.
- Open and close doors, windows, or drawers to test their operation, trimming edges to fit, as necessary.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Refinish wood surfaces on cabinets, doors, moldings, or floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Remove damaged exterior panels, and repair and replace structural frame members.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Inspect recreational vehicles to diagnose problems and perform necessary adjustment, repair, or overhaul.
- Pour compounds into transformer-case terminal openings to seal out moisture.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
- Lift units or parts such as motors or generators, using cranes or chain hoists, or signal crane operators to lift heavy parts or subassemblies.
- Record repairs required, parts used, and labor time.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Lubricate moving parts.
- Read service guides to find information needed to perform repairs.
- Inspect electrical connections, wiring, relays, charging resistance boxes, and storage batteries, following wiring diagrams.
- Scrape and clean units or parts, using cleaning solvents and equipment such as buffing wheels.
- Weld, braze, or solder electrical connections.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Steam-clean polishing and buffing wheels to remove abrasives and bonding materials, and spray, brush, or recoat surfaces as necessary.
- Set machinery for proper performance, using computers.
- Test equipment for overheating, using speed gauges and thermometers.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Maintain stocks of parts.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Solder, wrap, and coat wires to ensure proper insulation.
- Rewire electrical systems, and repair or replace electrical accessories.
- Clean cells, cell assemblies, glassware, leads, electrical connections, and battery poles, using scrapers, steam, water, emery cloths, power grinders, or acid.
- Rewind coils on cores in slots, or make replacement coils, using coil-winding machines.
- Test conditions, fluid levels, and specific gravities of electrolyte cells, using voltmeters, hydrometers, and thermometers.
- Add water or acid to battery cell solutions to obtain specified concentrations.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Hammer out dents and twists in tools and equipment.
- Drain and filter transformer oil and refill transformers with oil until coils are submerged.
- Repair and operate battery-charging equipment.
- Sharpen tools such as saws, picks, shovels, screwdrivers, and scoops, either manually or by using bench grinders and emery wheels.
- Inspect batteries for structural defects such as dented cans, damaged carbon rods and terminals, and defective seals.
- Test battery charges, and replace or recharge batteries as necessary.
- Bolt porcelain insulators to wood parts to assemble hot stools.
- Position and level battery cells, anodes, or cathodes, using hoists or leveling jacks, or signal other workers to perform positioning and leveling.
- Clean, rinse, and dry transformer cases, using boiling water, scrapers, solvents, hoses, and cloths.
- Pour compounds into transformer-case terminal openings to seal out moisture.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- Move and set up mobile homes or prefabricated buildings on owners' lots or at mobile home parks.
- Inspect, examine, and test the operation of parts or systems to evaluate operating condition and to determine if repairs are needed.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of plumbing fixtures.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, and diagrams.
- Confer with customers or read work orders to determine the nature and extent of damage to units.
- Install, repair, and replace units, fixtures, appliances, and other items and systems in mobile and modular homes, prefabricated buildings, or travel trailers, using hand tools or power tools.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Repair leaks in plumbing or gas lines, using caulking compounds and plastic or copper pipe.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, and hand tools.
- Open and close doors, windows, and drawers to test their operation, trimming edges to fit, using jackplanes or drawknives.
- Connect electrical systems to outside power sources and activate switches to test the operation of appliances and light fixtures.
- Refinish wood surfaces on cabinets, doors, moldings, and floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.
- Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.
- Reline or repair ladles and pouring spouts with refractory clay, using trowels.
- Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.
- Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.
- Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.
- Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.
- Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.
- Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.
- Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.
- Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.
- Dump and tamp clay in molds, using tamping tools.
- Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.
- Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.
- Install preformed metal scaffolding in interiors of cupolas, using hand tools.
- Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.
- Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.
- Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.
- Set starter locks and align and repair steering or throttle controls, using gauges, screwdrivers, or wrenches.
- Repair engine mechanical equipment, such as power tilts, bilge pumps, or power take-offs.
- Inspect and repair or adjust propellers or propeller shafts.
- Start motors and monitor performance for signs of malfunctioning, such as smoke, excessive vibration, or misfiring.
- Document inspection and test results and work performed or to be performed.
- Mount motors to boats, and operate boats at various speeds on waterways to conduct operational tests.
- Perform routine engine maintenance on motorboats, such as changing oil and filters.
- Replace parts, such as gears, magneto points, piston rings, or spark plugs, and reassemble engines.
- Idle motors and observe thermometers to determine the effectiveness of cooling systems.
- Adjust carburetor mixtures, electrical point settings, or timing while motors are running in water-filled test tanks.
- Disassemble and inspect motors to locate defective parts, using mechanic's hand tools and gauges.
- Adjust generators and replace faulty wiring, using hand tools and soldering irons.
- Repair or rework parts, using machine tools such as lathes, mills, drills, or grinders.
- Set starter locks and align and repair steering or throttle controls, using gauges, screwdrivers, or wrenches.
- Repair engine mechanical equipment, such as power tilts, bilge pumps, or power take-offs.
- Inspect and repair or adjust propellers or propeller shafts.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Record maintenance information, including test results, material usage, and repairs made.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Lubricate wearing surfaces of mechanical parts, using oils or other lubricants.
- Calibrate instrumentation, such as meters, gauges, and regulators, for pressure, temperature, flow, and level.
- Install, inspect and test electric meters, relays, and power sources to detect causes of malfunctions and inaccuracies, using hand tools and testing equipment.
- Test valves and regulators for leaks and accurate temperature and pressure settings, using precision testing equipment.
- Record meter readings and installation data on meter cards, work orders, or field service orders, or enter data into hand-held computers.
- Turn meters on or off to establish or close service.
- Shut off service and notify repair crews when major repairs are required, such as the replacement of underground pipes or wiring.
- Install regulators and related equipment such as gas meters, odorization units, and gas pressure telemetering equipment.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Turn valves to allow measured amounts of air or gas to pass through meters at specified flow rates.
- Report hazardous field situations and damaged or missing meters.
- Vary air pressure flowing into regulators and turn handles to assess functioning of valves and pistons.
- Examine valves or mechanical control device parts for defects, dents, or loose attachments, and mark malfunctioning areas of defective units.
- Mount and install meters and other electric equipment such as time clocks, transformers, and circuit breakers, using electricians' hand tools.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Investigate instances of illegal tapping into service lines.
- Trace and tag meters or house lines.
- Repair electric meters and components, such as transformers and relays, and replace metering devices, dial glasses, and faulty or incorrect wiring, using hand tools.
- Replace defective parts, such as bellows, range springs, and toggle switches, and reassemble units according to blueprints, using cam presses and hand tools.
- Measure tolerances of assembled and salvageable parts for conformance to standards or specifications, using gauges, micrometers, and calipers.
- Clean internal compartments and moving parts, using rags and cleaning compounds.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Reassemble repaired equipment, and solder top, front, and back case panels in place, using soldering guns, power tools, and hand tools.
- Attach air hoses to meter inlets, plug outlets, and observe gauges for pressure losses to test internal seams for leaks.
- Make adjustments to meter components, such as setscrews or timing mechanisms, so that they conform to specifications.
- Recommend and write up specifications for changes in hardware, such as house wiring.
- Clamp regulator units into vises on stages above water tanks, and attach compressed air hoses to intake ports.
- Collect money due on delinquent accounts.
- Splice and connect cables from meters or current transformers to pull boxes or switchboards, using hand tools.
- Attach pressurized meters to fixtures which submerge them in water, and observe meters for leaks.
- Advise customers on proper installation of valves or regulators and related equipment.
- Calibrate thermostats for specified temperature or pressure settings.
- Clean plant growth, scale, paint, soil, or rust from meter housings, using wire brushes, scrapers, buffers, sandblasters, or cleaning compounds.
- Connect hoses from provers to meter inlets and outlets, and raise prover bells until prover gauges register zero.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Position and fasten edges of tarpaulins over building, and tape vents to ensure air-tight environment and to check for leaks.
- Record work activities performed.
- Inspect premises to identify infestation source and extent of damage to property, wall, or roof porosity and access to infested locations.
- Recommend treatment and prevention methods for pest problems to clients.
- Spray or dust chemical solutions, powders, or gases into rooms, onto clothing, furnishings, or wood, or over marshlands, ditches, or catch basins.
- Clean work site after completion of job.
- Drive truck equipped with power spraying equipment.
- Measure area dimensions requiring treatment, calculate fumigant requirements, and estimate cost for service.
- Study preliminary reports or diagrams of infested area and determine treatment type required to eliminate and prevent recurrence of infestation.
- Direct, or assist other workers in, treatment or extermination processes to eliminate or control rodents, insects, or weeds.
- Post warning signs and lock building doors to secure area to be fumigated.
- Set mechanical traps, or place poisonous paste or bait in sewers, burrows, or ditches.
- Cut or bore openings in building or surrounding concrete, access infested areas, insert nozzle, and inject pesticide to impregnate ground.
- Clean and remove blockages from infested areas to facilitate spraying procedures and provide drainage, using brooms, mops, shovels, or rakes.
- Dig up and burn weeds, or spray them with herbicides.
- Position and fasten edges of tarpaulins over building, and tape vents to ensure air-tight environment and to check for leaks.
- Disassemble malfunctioning equipment and remove, repair, or replace defective parts, such as motors, clutches, or transformers.
- Test or calibrate components or equipment, following manufacturers' manuals and troubleshooting techniques, using hand tools, power tools, or measuring devices.
- Perform preventive maintenance or service, such as cleaning, lubricating, or adjusting equipment.
- Inspect, test, or troubleshoot malfunctioning medical or related equipment, following manufacturers' specifications and using test and analysis instruments.
- Keep records of maintenance, repair, and required updates of equipment.
- Examine medical equipment or facility's structural environment and check for proper use of equipment to protect patients and staff from electrical or mechanical hazards and to ensure compliance with safety regulations.
- Install medical equipment.
- Test, evaluate, and classify excess or in-use medical equipment and determine serviceability, condition, and disposition, in accordance with regulations.
- Plan and carry out work assignments, using blueprints, schematic drawings, technical manuals, wiring diagrams, or liquid or air flow sheets, following prescribed regulations, directives, or other instructions as required.
- Study technical manuals or attend training sessions provided by equipment manufacturers to maintain current knowledge.
- Explain or demonstrate correct operation or preventive maintenance of medical equipment to personnel.
- Research catalogs or repair part lists to locate sources for repair parts, requisitioning parts and recording their receipt.
- Repair shop equipment, metal furniture, or hospital equipment, including welding broken parts or replacing missing parts, or bring item into local shop for major repairs.
- Solder loose connections, using soldering iron.
- Compute power and space requirements for installing medical, dental, or related equipment and install units to manufacturers' specifications.
- Evaluate technical specifications to identify equipment or systems best suited for intended use and possible purchase, based on specifications, user needs, or technical requirements.
- Contribute expertise to develop medical maintenance standard operating procedures.
- Fabricate, dress down, or substitute parts or major new items to modify equipment to meet unique operational or research needs, working from job orders, sketches, modification orders, samples, or discussions with operating officials.
- Supervise or advise subordinate personnel.
- Make computations relating to load requirements of wiring or equipment, using algebraic expressions and standard formulas.
- Disassemble malfunctioning equipment and remove, repair, or replace defective parts, such as motors, clutches, or transformers.
- Clamp seals around valves to secure tanks.
- Signal other workers by telephone or radio to operate pumps, open and close valves, and check temperatures.
- Maintain and repair equipment, or report malfunctioning equipment to supervisors so that repairs can be scheduled.
- Monitor process indicators, instruments, gauges, and meters to detect and report any possible problems.
- Start pumps and open valves or use automated equipment to regulate the flow of oil in pipelines and into and out of tanks.
- Operate control panels to coordinate and regulate process variables such as temperature and pressure, and to direct product flow rate, according to process schedules.
- Verify that incoming and outgoing products are moving through the correct meters, and that meters are working properly.
- Patrol units to monitor the amount of oil in storage tanks, and to verify that activities and operations are safe, efficient, and in compliance with regulations.
- Plan movement of products through lines to processing, storage, and shipping units, using knowledge of system interconnections and capacities.
- Control or operate manifold and pumping systems to circulate liquids through a petroleum refinery.
- Operate auxiliary equipment and control multiple processing units during distilling or treating operations, moving controls that regulate valves, pumps, compressors, and auxiliary equipment.
- Collect product samples by turning bleeder valves, or by lowering containers into tanks to obtain oil samples.
- Read automatic gauges at specified intervals to determine the flow rate of oil into or from tanks, and the amount of oil in tanks.
- Synchronize activities with other pumphouses to ensure a continuous flow of products and a minimum of contamination between products.
- Record and compile operating data, instrument readings, documentation, and results of laboratory analyses.
- Conduct general housekeeping of units, including wiping up oil spills and performing general cleaning duties.
- Inspect pipelines, tightening connections and lubricating valves as necessary.
- Read and analyze specifications, schedules, logs, test results, and laboratory recommendations to determine how to set equipment controls to produce the required qualities and quantities of products.
- Perform tests to check the qualities and grades of products, such as assessing levels of bottom sediment, water, and foreign materials in oil samples, using centrifugal testers.
- Calculate test result values, using standard formulas.
- Clean interiors of processing units by circulating chemicals and solvents within units.
- Coordinate shutdowns and major projects.
- Prepare calculations for receipts and deliveries of oil and oil products.
- Lower thermometers into tanks to obtain temperature readings.
- Clamp seals around valves to secure tanks.
- Replace damaged glass on vehicles.
- File, grind, sand, and smooth filled or repaired surfaces, using power tools and hand tools.
- Inspect repaired vehicles for proper functioning, completion of work, dimensional accuracy, and overall appearance of paint job, and test-drive vehicles to ensure proper alignment and handling.
- Fit and weld replacement parts into place, using wrenches and welding equipment, and grind down welds to smooth them, using power grinders and other tools.
- Prime and paint repaired surfaces, using paint sprayguns and motorized sanders.
- Follow supervisors' instructions as to which parts to restore or replace and how much time the job should take.
- Sand body areas to be painted and cover bumpers, windows, and trim with masking tape or paper to protect them from the paint.
- Chain or clamp frames and sections to alignment machines that use hydraulic pressure to align damaged components.
- Position dolly blocks against surfaces of dented areas and beat opposite surfaces to remove dents, using hammers.
- Cut and tape plastic separating film to outside repair areas to avoid damaging surrounding surfaces during repair procedure and remove tape and wash surfaces after repairs are complete.
- Review damage reports, prepare or review repair cost estimates, and plan work to be performed.
- Fill small dents that cannot be worked out with plastic or solder.
- Remove damaged sections of vehicles using metal-cutting guns, air grinders and wrenches, and install replacement parts using wrenches or welding equipment.
- Remove small pits and dimples in body metal, using pick hammers and punches.
- Remove upholstery, accessories, electrical window-and-seat-operating equipment, and trim to gain access to vehicle bodies and fenders.
- Mix polyester resins and hardeners to be used in restoring damaged areas.
- Fit and secure windows, vinyl roofs, and metal trim to vehicle bodies, using caulking guns, adhesive brushes, and mallets.
- Adjust or align headlights, wheels, and brake systems.
- Remove damaged panels, and identify the family and properties of the plastic used on a vehicle.
- Apply heat to plastic panels, using hot-air welding guns or immersion in hot water, and press the softened panels back into shape by hand.
- Clean work areas, using air hoses, to remove damaged material and discarded fiberglass strips used in repair procedures.
- Soak fiberglass matting in resin mixtures and apply layers of matting over repair areas to specified thicknesses.
- Read specifications or confer with customers to determine the desired custom modifications for altering the appearance of vehicles.
- Cut openings in vehicle bodies for the installation of customized windows, using templates and power shears or chisels.
- Measure and mark vinyl material and cut material to size for roof installation, using rules, straightedges, and hand shears.
- Replace damaged glass on vehicles.
- Repair ships, bridge foundations, or other structures below the water line, using caulk, bolts, and hand tools.
- Take appropriate safety precautions, such as monitoring dive lengths and depths and registering with authorities before diving expeditions begin.
- Check and maintain diving equipment, such as helmets, masks, air tanks, harnesses, or gauges.
- Communicate with workers on the surface while underwater, using signal lines or telephones.
- Descend into water with the aid of diver helpers, using scuba gear or diving suits.
- Obtain information about diving tasks and environmental conditions.
- Supervise or train other divers, including hobby divers.
- Inspect the condition of underwater steel or wood structures.
- Inspect and test docks, ships, buoyage systems, plant intakes or outflows, or underwater pipelines, cables, or sewers, using closed circuit television, still photography, and testing equipment.
- Recover objects by placing rigging around sunken objects, hooking rigging to crane lines, and operating winches, derricks, or cranes to raise objects.
- Operate underwater video, sonar, recording, or related equipment to investigate underwater structures or marine life.
- Take test samples or photographs to assess the condition of vessels or structures.
- Cut and weld steel, using underwater welding equipment, jigs, and supports.
- Install, inspect, clean, or repair piping or valves.
- Carry out non-destructive testing, such as tests for cracks on the legs of oil rigs at sea.
- Install pilings or footings for piers or bridges.
- Salvage wrecked ships or their cargo, using pneumatic power velocity and hydraulic tools and explosive charges, when necessary.
- Remove obstructions from strainers or marine railway or launching ways, using pneumatic or power hand tools.
- Set or guide placement of pilings or sandbags to provide support for structures, such as docks, bridges, cofferdams, or platforms.
- Perform activities related to underwater search and rescue, salvage, recovery, or cleanup operations.
- Perform offshore oil or gas exploration or extraction duties, such as conducting underwater surveys or repairing and maintaining drilling rigs or platforms.
- Drill holes in rock and rig explosives for underwater demolitions.
- Remove rubbish or pollution from the sea.
- Set up dive sites for recreational instruction.
- Cultivate or harvest marine species or perform routine work on fish farms.
- Repair ships, bridge foundations, or other structures below the water line, using caulk, bolts, and hand tools.
