- Test units for operability before and after repairs.
Occupations with related tasks Save Table: XLSX CSV
- Examine or test operation of parts or systems to ensure completeness of repairs.
- Explain proper operation of vehicle systems to customers.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, or hand tools.
- Repair plumbing or propane gas lines, using caulking compounds and plastic or copper pipe.
- Confer with customers, read work orders, or examine vehicles needing repair to determine the nature and extent of damage.
- Connect electrical systems to outside power sources, and activate switches to test the operation of appliances or light fixtures.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of toilets or sinks.
- Inspect recreational vehicles to diagnose problems and perform necessary adjustment, repair, or overhaul.
- Inspect, repair, or replace brake systems.
- Diagnose and repair furnace or air conditioning systems.
- Repair leaks with caulking compound or replace pipes, using pipe wrenches.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, or diagrams.
- Remove damaged exterior panels, and repair and replace structural frame members.
- Open and close doors, windows, or drawers to test their operation, trimming edges to fit, as necessary.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Refinish wood surfaces on cabinets, doors, moldings, or floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Examine or test operation of parts or systems to ensure completeness of repairs.
- Test mechanical products and equipment after repair or assembly to ensure proper performance and compliance with manufacturers' specifications.
- Repair and replace damaged or worn parts.
- Operate and inspect machines or heavy equipment to diagnose defects.
- Read and understand operating manuals, blueprints, and technical drawings.
- Dismantle and reassemble heavy equipment using hoists and hand tools.
- Overhaul and test machines or equipment to ensure operating efficiency.
- Adjust, maintain, and repair or replace subassemblies, such as transmissions and crawler heads, using hand tools, jacks, and cranes.
- Repair, rewire, and troubleshoot electrical systems.
- Diagnose faults or malfunctions to determine required repairs, using engine diagnostic equipment such as computerized test equipment and calibration devices.
- Examine parts for damage or excessive wear, using micrometers and gauges.
- Weld or solder broken parts and structural members, using electric or gas welders and soldering tools.
- Research, order, and maintain parts inventory for services and repairs.
- Fit bearings to adjust, repair, or overhaul mobile mechanical, hydraulic, and pneumatic equipment.
- Schedule maintenance for industrial machines and equipment, and keep equipment service records.
- Clean, lubricate, and perform other routine maintenance work on equipment and vehicles.
- Assemble gear systems, and align frames and gears.
- Clean parts by spraying them with grease solvent or immersing them in tanks of solvent.
- Adjust and maintain industrial machinery, using control and regulating devices.
- Fabricate needed parts or items from sheet metal.
- Direct workers who are assembling or disassembling equipment or cleaning parts.
- Test mechanical products and equipment after repair or assembly to ensure proper performance and compliance with manufacturers' specifications.
- Inspect, test, and measure completed work, using devices such as hand tools or gauges to verify conformance to standards or repair requirements.
- Inspect and monitor work areas, examine tools and equipment, and provide employee safety training to prevent, detect, and correct unsafe conditions or violations of procedures and safety rules.
- Interpret specifications, blueprints, or job orders to construct templates and lay out reference points for workers.
- Monitor employees' work levels and review work performance.
- Perform skilled repair or maintenance operations, using equipment such as hand or power tools, hydraulic presses or shears, or welding equipment.
- Compute estimates and actual costs of factors such as materials, labor, or outside contractors.
- Monitor tool and part inventories and the condition and maintenance of shops to ensure adequate working conditions.
- Requisition materials and supplies, such as tools, equipment, or replacement parts.
- Confer with personnel, such as management, engineering, quality control, customer, or union workers' representatives, to coordinate work activities, resolve employee grievances, or identify and review resource needs.
- Determine schedules, sequences, and assignments for work activities, based on work priority, quantity of equipment, and skill of personnel.
- Examine objects, systems, or facilities and analyze information to determine needed installations, services, or repairs.
- Counsel employees about work-related issues and assist employees to correct job-skill deficiencies.
- Recommend or initiate personnel actions, such as hires, promotions, transfers, discharges, or disciplinary measures.
- Investigate accidents or injuries and prepare reports of findings.
- Conduct or arrange for worker training in safety, repair, or maintenance techniques, operational procedures, or equipment use.
- Develop, implement, or evaluate maintenance policies and procedures.
- Meet with vendors or suppliers to discuss products used in repair work.
- Participate in budget preparation and administration, coordinating purchasing and documentation and monitoring departmental expenditures.
- Review, evaluate, accept, and coordinate completion of work bid from contractors.
- Compile operational or personnel records, such as time and production records, inventory data, repair or maintenance statistics, or test results.
- Develop or implement electronic maintenance programs or computer information management systems.
- Design equipment configurations to meet personnel needs.
- Inspect, test, and measure completed work, using devices such as hand tools or gauges to verify conformance to standards or repair requirements.
- Inspect repaired vehicles for proper functioning, completion of work, dimensional accuracy, and overall appearance of paint job, and test-drive vehicles to ensure proper alignment and handling.
- File, grind, sand, and smooth filled or repaired surfaces, using power tools and hand tools.
- Fit and weld replacement parts into place, using wrenches and welding equipment, and grind down welds to smooth them, using power grinders and other tools.
- Prime and paint repaired surfaces, using paint sprayguns and motorized sanders.
- Follow supervisors' instructions as to which parts to restore or replace and how much time the job should take.
- Sand body areas to be painted and cover bumpers, windows, and trim with masking tape or paper to protect them from the paint.
- Chain or clamp frames and sections to alignment machines that use hydraulic pressure to align damaged components.
- Position dolly blocks against surfaces of dented areas and beat opposite surfaces to remove dents, using hammers.
- Cut and tape plastic separating film to outside repair areas to avoid damaging surrounding surfaces during repair procedure and remove tape and wash surfaces after repairs are complete.
- Review damage reports, prepare or review repair cost estimates, and plan work to be performed.
- Fill small dents that cannot be worked out with plastic or solder.
- Remove damaged sections of vehicles using metal-cutting guns, air grinders and wrenches, and install replacement parts using wrenches or welding equipment.
- Remove small pits and dimples in body metal, using pick hammers and punches.
- Remove upholstery, accessories, electrical window-and-seat-operating equipment, and trim to gain access to vehicle bodies and fenders.
- Mix polyester resins and hardeners to be used in restoring damaged areas.
- Fit and secure windows, vinyl roofs, and metal trim to vehicle bodies, using caulking guns, adhesive brushes, and mallets.
- Adjust or align headlights, wheels, and brake systems.
- Replace damaged glass on vehicles.
- Remove damaged panels, and identify the family and properties of the plastic used on a vehicle.
- Apply heat to plastic panels, using hot-air welding guns or immersion in hot water, and press the softened panels back into shape by hand.
- Clean work areas, using air hoses, to remove damaged material and discarded fiberglass strips used in repair procedures.
- Soak fiberglass matting in resin mixtures and apply layers of matting over repair areas to specified thicknesses.
- Read specifications or confer with customers to determine the desired custom modifications for altering the appearance of vehicles.
- Cut openings in vehicle bodies for the installation of customized windows, using templates and power shears or chisels.
- Measure and mark vinyl material and cut material to size for roof installation, using rules, straightedges, and hand shears.
- Inspect repaired vehicles for proper functioning, completion of work, dimensional accuracy, and overall appearance of paint job, and test-drive vehicles to ensure proper alignment and handling.
- Inspect completed work to ensure all hardware is tight, antennas are level, hangers are properly fastened, proper support is in place, or adequate weather proofing has been installed.
- Run appropriate power, ground, or coaxial cables.
- Test operation of tower transmission components, using sweep testing tools or software.
- Install all necessary transmission equipment components, including antennas or antenna mounts, surge arrestors, transmission lines, connectors, or tower-mounted amplifiers (TMAs).
- Read work orders, blueprints, plans, datasheets or site drawings to determine work to be done.
- Replace existing antennas with new antennas as directed.
- Bolt equipment into place, using hand or power tools.
- Install, connect, or test underground or aboveground grounding systems.
- Complete reports related to project status, progress, or other work details, using computer software.
- Check antenna positioning to ensure specified azimuths or mechanical tilts and adjust as necessary.
- Transport equipment to work sites, using utility trucks and equipment trailers.
- Take site survey photos or photos of work performed, using digital cameras.
- Climb towers to access components, using safety equipment, such as full-body harnesses.
- Climb communication towers to install, replace, or repair antennas or auxiliary equipment used to transmit and receive radio waves.
- Lift equipment into position, using cranes and rigging tools or equipment, such as gin poles.
- Perform maintenance or repair work on existing tower equipment, using hand or power tools.
- Locate tower sites where work is to be performed, using mapping software.
- Install or repair tower lighting components, including strobes, beacons, or lighting controllers.
- Calibrate and align components, using scales, gauges, and other measuring instruments.
- Examine malfunctioning radio equipment to locate defects such as loose connections, broken wires, or burned-out components, using schematic diagrams and test equipment.
- Insert plugs into receptacles and bolt or screw leads to terminals to connect equipment to power sources, using hand tools.
- Install, adjust, and repair stationary and mobile radio transmitting and receiving equipment and two-way radio communication systems.
- Monitor radio range stations to detect transmission flaws and adjust controls to eliminate flaws.
- Mount equipment on transmission towers and in vehicles such as ships or ambulances.
- Remove and replace defective components and parts such as conductors, resistors, semiconductors, and integrated circuits, using soldering irons, wire cutters, and hand tools.
- Repair circuits, wiring, and soldering, using soldering irons and hand tools to install parts and adjust connections.
- Test batteries, using hydrometers and ammeters, and charge batteries as necessary.
- Test emergency transmitters to ensure their readiness for immediate use.
- Test equipment functions such as signal strength and quality, transmission capacity, interference, and signal delay, using equipment such as oscilloscopes, circuit analyzers, frequency meters, and wattmeters.
- Turn setscrews to adjust receivers for maximum sensitivity and transmitters for maximum output.
- Inspect completed work to ensure all hardware is tight, antennas are level, hangers are properly fastened, proper support is in place, or adequate weather proofing has been installed.
- Inspect completed work to certify that maintenance meets standards and that aircraft are ready for operation.
- Examine and inspect aircraft components, including landing gear, hydraulic systems, and deicers to locate cracks, breaks, leaks, or other problems.
- Conduct routine and special inspections as required by regulations.
- Read and interpret maintenance manuals, service bulletins, and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.
- Maintain repair logs, documenting all preventive and corrective aircraft maintenance.
- Modify aircraft structures, space vehicles, systems, or components, following drawings, schematics, charts, engineering orders, and technical publications.
- Inspect airframes for wear or other defects.
- Measure parts for wear, using precision instruments.
- Obtain fuel and oil samples and check them for contamination.
- Maintain, repair, and rebuild aircraft structures, functional components, and parts, such as wings and fuselage, rigging, hydraulic units, oxygen systems, fuel systems, electrical systems, gaskets, or seals.
- Replace or repair worn, defective, or damaged components, using hand tools, gauges, and testing equipment.
- Read and interpret pilots' descriptions of problems to diagnose causes.
- Test operation of engines and other systems, using test equipment, such as ignition analyzers, compression checkers, distributor timers, or ammeters.
- Measure the tension of control cables.
- Spread plastic film over areas to be repaired to prevent damage to surrounding areas.
- Remove or install aircraft engines, using hoists or forklift trucks.
- Assemble and install electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools.
- Locate and mark dimensions and reference lines on defective or replacement parts, using templates, scribes, compasses, and steel rules.
- Fabricate defective sections or parts, using metal fabricating machines, saws, brakes, shears, and grinders.
- Reassemble engines following repair or inspection and reinstall engines in aircraft.
- Service and maintain aircraft and related apparatus by performing activities such as flushing crankcases, cleaning screens, and or moving parts.
- Clean, refuel, and change oil in line service aircraft.
- Trim and shape replacement body sections to specified sizes and fits and secure sections in place, using adhesives, hand tools, and power tools.
- Accompany aircraft on flights to make in-flight adjustments and corrections.
- Remove or cut out defective parts or drill holes to gain access to internal defects or damage, using drills and punches.
- Install and align repaired or replacement parts for subsequent riveting or welding, using clamps and wrenches.
- Inventory and requisition or order supplies, parts, materials, and equipment.
- Clean, strip, prime, and sand structural surfaces and materials to prepare them for bonding.
- Communicate with other workers to coordinate fitting and alignment of heavy parts, or to facilitate processing of repair parts.
- Examine engines through specially designed openings while working from ladders or scaffolds, or use hoists or lifts to remove the entire engine from an aircraft.
- Check for corrosion, distortion, and invisible cracks in the fuselage, wings, and tail, using x-ray and magnetic inspection equipment.
- Disassemble engines and inspect parts, such as turbine blades or cylinders, for corrosion, wear, warping, cracks, and leaks, using precision measuring instruments, x-rays, and magnetic inspection equipment.
- Cure bonded structures, using portable or stationary curing equipment.
- Listen to operating engines to detect and diagnose malfunctions, such as sticking or burned valves.
- Clean engines, sediment bulk and screens, and carburetors, adjusting carburetor float levels.
- Determine repair limits for engine hot section parts.
- Remove, inspect, repair, and install in-flight refueling stores and external fuel tanks.
- Prepare and paint aircraft surfaces.
- Inspect completed work to certify that maintenance meets standards and that aircraft are ready for operation.
