- Assemble and install components of timepieces to complete mechanisms, using watchmakers' tools and loupes.
Occupations with related tasks Save Table: XLSX CSV
Closely Related Tasks | All Related Tasks | Job Zone | Code | Occupation |
4 | 4 | 2 | 51-2011.00 | Aircraft Structure, Surfaces, Rigging, and Systems Assemblers |
2 | 3 | 3 | 51-4061.00 | Model Makers, Metal and Plastic |
2 | 2 | 2 | 51-4122.00 | Welding, Soldering, and Brazing Machine Setters, Operators, and Tenders |
1 | 4 | 2 | 51-9195.00 | Molders, Shapers, and Casters, Except Metal and Plastic |
1 | 2 | 2 | 51-4192.00 | Layout Workers, Metal and Plastic |
1 | 1 | 2 | 51-2021.00 | Coil Winders, Tapers, and Finishers |
1 | 1 | 2 | 51-4032.00 | Drilling and Boring Machine Tool Setters, Operators, and Tenders, Metal and Plastic |
- Assemble parts, fittings, or subassemblies on aircraft, using layout tools, hand tools, power tools, or fasteners, such as bolts, screws, rivets, or clamps.
- Fabricate parts needed for assembly or installation, using shop machinery or equipment.
- Assemble prefabricated parts to form subassemblies.
- Assemble prototypes or integrated-technology demonstrators of new or emerging environmental technologies for aircraft.
- Read blueprints, illustrations, or specifications to determine layouts, sequences of operations, or identities or relationships of parts.
- Attach brackets, hinges, or clips to secure or support components or subassemblies, using bolts, screws, rivets, chemical bonding, or welding.
- Inspect or test installed units, parts, systems, or assemblies for fit, alignment, performance, defects, or compliance with standards, using measuring instruments or test equipment.
- Adjust, repair, rework, or replace parts or assemblies to ensure proper operation.
- Cut, trim, file, bend, or smooth parts to ensure proper fit and clearance.
- Layout and mark reference points and locations for installation of parts or components, using jigs, templates, or measuring and marking instruments.
- Clean, oil, or coat system components, as necessary, before assembly or attachment.
- Set, align, adjust, or synchronize aircraft armament or rigging or control system components to established tolerances or requirements, using sighting devices and hand tools.
- Join structural assemblies, such as wings, tails, or fuselage.
- Position and align subassemblies in jigs or fixtures, using measuring instruments and following blueprint lines and index points.
- Swage fittings onto cables, using swaging machines.
- Manually install structural assemblies or signal crane operators to position assemblies for joining.
- Align, fit, assemble, connect, or install system components, using jigs, fixtures, measuring instruments, hand tools, or power tools.
- Set up or operate machines or systems to crimp, cut, bend, form, swage, flare, bead, burr, or straighten tubing, according to specifications.
- Place and connect control cables to electronically controlled units, using hand tools, ring locks, cotter keys, threaded connectors, turnbuckles, or related devices.
- Install mechanical linkages and actuators, using tensiometers to verify tension of cables.
- Clean aircraft structures, parts, or components, using aqueous, semi-aqueous, aliphatic hydrocarbon, or organic solvent cleaning products or techniques to reduce carbon or other harmful emissions.
- Install accessories in swaging machines, using hand tools.
- Mark identifying information on tubing or cable assemblies, using etching devices, labels, rubber stamps, or other methods.
- Verify dimensions of cable assemblies or positions of fittings, using measuring instruments.
- Weld tubing and fittings or solder cable ends, using tack welders, induction brazing chambers, or other equipment.
- Splice cables, using clamps and fittings, or reweave cable strands.
- Fit and fasten sheet metal coverings to surface areas or other sections of aircraft prior to welding or riveting.
- Capture or segregate waste material, such as aluminum swarf, machine cutting fluid, or solvents, for recycling or environmentally responsible disposal.
- Cut cables and tubing, using master templates, measuring instruments, and cable cutters or saws.
- Monitor robotic assembly equipment, such as snake-arm robots, used to assemble, seal, or swage aircraft structures.
- Assemble parts, fittings, or subassemblies on aircraft, using layout tools, hand tools, power tools, or fasteners, such as bolts, screws, rivets, or clamps.
- Fabricate parts needed for assembly or installation, using shop machinery or equipment.
- Assemble prefabricated parts to form subassemblies.
- Assemble prototypes or integrated-technology demonstrators of new or emerging environmental technologies for aircraft.
- Align, fit, and join parts, using bolts and screws or by welding or gluing.
- Assemble mechanical, electrical, and electronic components into models or prototypes, using hand tools, power tools, and fabricating machines.
- Devise and construct tools, dies, molds, jigs, and fixtures, or modify existing tools and equipment.
- Study blueprints, drawings, and sketches to determine material dimensions, required equipment, and operations sequences.
- Inspect and test products to verify conformance to specifications, using precision measuring instruments or circuit testers.
- Drill, countersink, and ream holes in parts and assemblies for bolts, screws, and other fasteners, using power tools.
- Cut, shape, and form metal parts, using lathes, power saws, snips, power brakes and shears, files, and mallets.
- Set up and operate machines, such as lathes, drill presses, punch presses, or bandsaws, to fabricate prototypes or models.
- Rework or alter component model or parts as required to ensure that products meet standards.
- Grind, file, and sand parts to finished dimensions.
- Program computer numerical control (CNC) machines to fabricate model parts.
- Lay out and mark reference points and dimensions on materials, using measuring instruments and drawing or scribing tools.
- Use computer-aided design (CAD) and computer-aided manufacturing (CAM) software or hardware to fabricate model parts.
- Consult and confer with engineering personnel to discuss developmental problems and to recommend product modifications.
- Record specifications, production operations, and final dimensions of models for use in establishing operating standards and procedures.
- Wire and solder electrical and electronic connections and components.
- Align, fit, and join parts, using bolts and screws or by welding or gluing.
- Assemble mechanical, electrical, and electronic components into models or prototypes, using hand tools, power tools, and fabricating machines.
- Devise and construct tools, dies, molds, jigs, and fixtures, or modify existing tools and equipment.
- Assemble, align, and clamp workpieces into holding fixtures to bond, heat-treat, or solder fabricated metal components.
- Lay out, fit, or connect parts to be bonded, calculating production measurements, as necessary.
- Inspect, measure, or test completed metal workpieces to ensure conformance to specifications, using measuring and testing devices.
- Read blueprints, work orders, or production schedules to determine product or job instructions or specifications.
- Set up, operate, or tend welding machines that join or bond components to fabricate metal products or assemblies.
- Correct problems by adjusting controls or by stopping machines and opening holding devices.
- Give directions to other workers regarding machine set-up and use.
- Select, position, align, and bolt jigs, holding fixtures, guides, or stops onto machines, using measuring instruments and hand tools.
- Mark weld points and positions of components on workpieces, using rules, squares, templates, or scribes.
- Transfer components, metal products, or assemblies, using moving equipment.
- Clean, lubricate, maintain, and adjust equipment to maintain efficient operation, using air hoses, cleaning fluids, and hand tools.
- Prepare metal surfaces or workpieces, using hand-operated equipment, such as grinders, cutters, or drills.
- Conduct trial runs before welding, soldering, or brazing, and make necessary adjustments to equipment.
- Remove completed workpieces or parts from machinery, using hand tools.
- Tend auxiliary equipment used in welding processes.
- Load or feed workpieces into welding machines to join or bond components.
- Observe meters, gauges, or machine operations to ensure that soldering or brazing processes meet specifications.
- Turn and press knobs and buttons or enter operating instructions into computers to adjust and start welding machines.
- Compute and record settings for new work, applying knowledge of metal properties, principles of welding, and shop mathematics.
- Set dials and timing controls to regulate electrical current, gas flow pressure, heating or cooling cycles, or shut-off.
- Record operational information on specified production reports.
- Select torch tips, alloys, flux, coil, tubing, or wire, according to metal types or thicknesses, data charts, or records.
- Fill hoppers and position spouts to direct flow of flux or manually brush flux onto seams of workpieces.
- Start, monitor, and adjust robotic welding production lines.
- Devise or build fixtures or jigs used to hold parts in place during welding, brazing, or soldering.
- Add chemicals or materials to workpieces or machines to facilitate bonding or to cool workpieces.
- Immerse completed workpieces into water or acid baths to cool and clean components.
- Dress electrodes, using tip dressers, files, emery cloths, or dressing wheels.
- Anneal finished workpieces to relieve internal stress.
- Assemble, align, and clamp workpieces into holding fixtures to bond, heat-treat, or solder fabricated metal components.
- Lay out, fit, or connect parts to be bonded, calculating production measurements, as necessary.
- Align and assemble parts to produce completed products, using gauges and hand tools.
- Assemble, insert, and adjust wires, tubes, cores, fittings, rods, or patterns into molds, using hand tools and depth gauges.
- Operate molding machines that compact sand in flasks to form molds.
- Construct or form molds for use in casting clay or plaster objects, using plaster, fiberglass, rubber, casting machines, patterns, or flasks.
- Read work orders or examine parts to determine parts or sections of products to be produced.
- Trim or remove excess material, using scrapers, knives, or band saws.
- Brush or spray mold surfaces with parting agents or insert paper into molds to ensure smoothness and prevent sticking or seepage.
- Engrave or stamp identifying symbols, letters, or numbers on products.
- Clean, finish, and lubricate molds and mold parts.
- Separate models or patterns from molds and examine products for accuracy.
- Set the proper operating temperature for each casting.
- Load or stack filled molds in ovens, dryers, or curing boxes, or on storage racks or carts.
- Operate and adjust controls of heating equipment to melt material or to cure, dry, or bake filled molds.
- Select sizes and types of molds according to instructions.
- Patch broken edges or fractures, using clay or plaster.
- Withdraw cores or other loose mold members after castings solidify.
- Repair mold defects, such as cracks or broken edges, using patterns, mold boxes, or hand tools.
- Measure and cut products to specified dimensions, using measuring and cutting instruments.
- Smooth surfaces of molds, using scraping tools or sandpaper.
- Measure ingredients and mix molding, casting material, or sealing compounds to prescribed consistencies, according to formulas.
- Remove excess materials and level and smooth wet mold mixtures.
- Place forms around models and separately immerse each half portion of a model in plaster, wax, or other mold-making materials.
- Verify dimensions of products, using measuring instruments, such as calipers, vernier gauges, or protractors.
- Bore holes or cut grates, risers, or pouring spouts in molds, using power tools.
- Locate and scribe parting lines on patterns, using measuring instruments, such as calipers, squares, or depth gauges.
- Tap or tilt molds to ensure uniform distribution of materials.
- Pour, pack, spread, or press plaster, concrete, or other materials into or around models or molds.
- Align and assemble parts to produce completed products, using gauges and hand tools.
- Assemble, insert, and adjust wires, tubes, cores, fittings, rods, or patterns into molds, using hand tools and depth gauges.
- Operate molding machines that compact sand in flasks to form molds.
- Construct or form molds for use in casting clay or plaster objects, using plaster, fiberglass, rubber, casting machines, patterns, or flasks.
- Lay out and fabricate metal structural parts such as plates, bulkheads, and frames.
- Design and prepare templates of wood, paper, or metal.
- Mark curves, lines, holes, dimensions, and welding symbols onto workpieces, using scribes, soapstones, punches, and hand drills.
- Plan locations and sequences of cutting, drilling, bending, rolling, punching, and welding operations, using compasses, protractors, dividers, and rules.
- Fit and align fabricated parts to be welded or assembled.
- Locate center lines and verify template positions, using measuring instruments such as gauge blocks, height gauges, and dial indicators.
- Plan and develop layouts from blueprints and templates, applying knowledge of trigonometry, design, effects of heat, and properties of metals.
- Compute layout dimensions, and determine and mark reference points on metal stock or workpieces for further processing, such as welding and assembly.
- Lift and position workpieces in relation to surface plates, manually or with hoists, and using parallel blocks and angle plates.
- Install doors, hatches, brackets, and clips.
- Brace parts in position within hulls or ships for riveting or welding.
- Inspect machined parts to verify conformance to specifications.
- Add dimensional details to blueprints or drawings made by other workers.
- Apply pigment to layout surfaces, using paint brushes.
- Lay out and fabricate metal structural parts such as plates, bulkheads, and frames.
- Design and prepare templates of wood, paper, or metal.
- Line slots with sheet insulation, and insert coils into slots.
- Operate or tend wire-coiling machines to wind wire coils used in electrical components such as resistors and transformers, and in electrical equipment and instruments such as bobbins and generators.
- Attach, alter, and trim materials such as wire, insulation, and coils, using hand tools.
- Cut, strip, and bend wire leads at ends of coils, using pliers and wire scrapers.
- Review work orders and specifications to determine materials needed and types of parts to be processed.
- Select and load materials such as workpieces, objects, and machine parts onto equipment used in coiling processes.
- Record production and operational data on specified forms.
- Stop machines to remove completed components, using hand tools.
- Examine and test wired electrical components such as motors, armatures, and stators, using measuring devices, and record test results.
- Apply solutions or paints to wired electrical components, using hand tools, and bake components.
- Disassemble and assemble motors, and repair and maintain electrical components and machinery parts, using hand tools.
- Line slots with sheet insulation, and insert coils into slots.
- Perform minor assembly, such as fastening parts with nuts, bolts, or screws, using power tools or hand tools.
- Verify conformance of machined work to specifications, using measuring instruments, such as calipers, micrometers, or fixed or telescoping gauges.
- Study machining instructions, job orders, or blueprints to determine dimensional or finish specifications, sequences of operations, setups, or tooling requirements.
- Move machine controls to lower tools to workpieces and to engage automatic feeds.
- Verify that workpiece reference lines are parallel to the axis of table rotation, using dial indicators mounted in spindles.
- Establish zero reference points on workpieces, such as at the intersections of two edges or over hole locations.
- Change worn cutting tools, using wrenches.
- Select and set cutting speeds, feed rates, depths of cuts, and cutting tools, according to machining instructions or knowledge of metal properties.
- Position and secure workpieces on tables, using bolts, jigs, clamps, shims, or other holding devices.
- Observe drilling or boring machine operations to detect any problems.
- Lift workpieces onto work tables either manually or with hoists or direct crane operators to lift and position workpieces.
- Turn valves and direct flow of coolants or cutting oil over cutting areas.
- Install tools in spindles.
- Operate single- or multiple-spindle drill presses to bore holes so that machining operations can be performed on metal or plastic workpieces.
- Lay out reference lines and machining locations on work, using layout tools, and applying knowledge of shop math and layout techniques.
- Sharpen cutting tools, using bench grinders.
- Operate tracing attachments to duplicate contours from templates or models.
- Perform minor assembly, such as fastening parts with nuts, bolts, or screws, using power tools or hand tools.