- Inspect structures to assess material or equipment needs, to establish the sequence of pipe installations, or to plan installation around obstructions, such as electrical wiring.
Occupations with related tasks Save Table: XLSX CSV
- Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.
- Examine structural timbers and supports to detect decay, and replace timbers as required, using hand tools, nuts, and bolts.
- Follow established safety rules and regulations and maintain a safe and clean environment.
- Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
- Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue.
- Study specifications in blueprints, sketches, or building plans to prepare project layout and determine dimensions and materials required.
- Shape or cut materials to specified measurements, using hand tools, machines, or power saws.
- Verify trueness of structure, using plumb bob and level.
- Erect scaffolding or ladders for assembling structures above ground level.
- Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.
- Maintain records, document actions, and present written progress reports.
- Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.
- Maintain job records and schedule work crew.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Bore boltholes in timber, masonry or concrete walls, using power drill.
- Install rough door and window frames, subflooring, fixtures, or temporary supports in structures undergoing construction or repair.
- Dig or direct digging of post holes and set poles to support structures.
- Cover subfloors with building paper to keep out moisture and lay hardwood, parquet, or wood-strip-block floors by nailing floors to subfloor or cementing them to mastic or asphalt base.
- Construct forms or chutes for pouring concrete.
- Arrange for subcontractors to deal with special areas, such as heating or electrical wiring work.
- Build or repair cabinets, doors, frameworks, floors, or other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, or power tools.
- Finish surfaces of woodwork or wallboard in houses or buildings, using paint, hand tools, or paneling.
- Select and order lumber or other required materials.
- Work with or remove hazardous material.
- Fill cracks or other defects in plaster or plasterboard and sand patch, using patching plaster, trowel, and sanding tool.
- Prepare cost estimates for clients or employers.
- Perform minor plumbing, welding, or concrete mixing work.
- Apply shock-absorbing, sound-deadening, or decorative paneling to ceilings or walls.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
- Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.
- Examine structural timbers and supports to detect decay, and replace timbers as required, using hand tools, nuts, and bolts.
- Examine brickwork or structure to determine need for repair.
- Measure distance from reference points and mark guidelines to lay out work, using plumb bobs and levels.
- Construct corners by fastening in plumb position a corner pole or building a corner pyramid of bricks, and filling in between the corners using a line from corner to corner to guide each course, or layer, of brick.
- Apply and smooth mortar or other mixture over work surface.
- Calculate angles and courses and determine vertical and horizontal alignment of courses.
- Break or cut bricks, tiles, or blocks to size, using trowel edge, hammer, or power saw.
- Interpret blueprints and drawings to determine specifications and to calculate the materials required.
- Remove excess mortar with trowels and hand tools, and finish mortar joints with jointing tools, for a sealed, uniform appearance.
- Fasten or fuse brick or other building material to structure with wire clamps, anchor holes, torch, or cement.
- Clean working surface to remove scale, dust, soot, or chips of brick and mortar, using broom, wire brush, or scraper.
- Mix specified amounts of sand, clay, dirt, or mortar powder with water to form refractory mixtures.
- Remove burned or damaged brick or mortar, using sledgehammer, crowbar, chipping gun, or chisel.
- Lay and align bricks, blocks, or tiles to build or repair structures or high temperature equipment, such as cupola, kilns, ovens, or furnaces.
- Spray or spread refractory material over brickwork to protect against deterioration.
- Examine brickwork or structure to determine need for repair.
- Visit site and record information about access, drainage and topography, and availability of utility services.
- Analyze blueprints and other documentation to prepare time, cost, materials, and labor estimates.
- Confer with engineers, architects, owners, contractors, and subcontractors on changes and adjustments to cost estimates.
- Collect historical cost data to estimate costs for current or future products.
- Assess cost effectiveness of products, projects or services, tracking actual costs relative to bids as the project develops.
- Consult with clients, vendors, personnel in other departments, or construction foremen to discuss and formulate estimates and resolve issues.
- Establish and maintain tendering process, and conduct negotiations.
- Prepare estimates for use in selecting vendors or subcontractors.
- Prepare estimates used by management for purposes such as planning, organizing, and scheduling work.
- Set up cost monitoring and reporting systems and procedures.
- Review material and labor requirements to decide whether it is more cost-effective to produce or purchase components.
- Prepare cost and expenditure statements and other necessary documentation at regular intervals for the duration of the project.
- Conduct special studies to develop and establish standard hour and related cost data or to reduce cost.
- Prepare and maintain a directory of suppliers, contractors and subcontractors.
- Visit site and record information about access, drainage and topography, and availability of utility services.
- Inspect surface to be covered to ensure that it is firm and dry.
- Sweep, scrape, sand, or chip dirt and irregularities to clean base surfaces, correcting imperfections that may show through the covering.
- Cut flooring material to fit around obstructions.
- Trim excess covering materials, tack edges, and join sections of covering material to form tight joint.
- Form a smooth foundation by stapling plywood or Masonite over the floor or by brushing waterproof compound onto surface and filling cracks with plaster, putty, or grout to seal pores.
- Measure and mark guidelines on surfaces or foundations, using chalk lines and dividers.
- Cut covering and foundation materials, according to blueprints and sketches.
- Roll and press sheet wall and floor covering into cement base to smooth and finish surface, using hand roller.
- Apply adhesive cement to floor or wall material to join and adhere foundation material.
- Determine traffic areas and decide location of seams.
- Lay out, position, and apply shock-absorbing, sound-deadening, or decorative coverings to floors, walls, and cabinets, following guidelines to keep courses straight and create designs.
- Remove excess cement to clean finished surface.
- Disconnect and remove appliances, light fixtures, and worn floor and wall covering from floors, walls, and cabinets.
- Heat and soften floor covering materials to patch cracks or fit floor coverings around irregular surfaces, using blowtorch.
- Inspect surface to be covered to ensure that it is firm and dry.
- Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly.
- Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting.
- Join edges of carpet and seam edges where necessary, by sewing or by using tape with glue and heated carpet iron.
- Cut and trim carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer.
- Plan the layout of the carpet, allowing for expected traffic patterns and placing seams for best appearance and longest wear.
- Stretch carpet to align with walls and ensure a smooth surface, and press carpet in place over tack strips or use staples, tape, tacks or glue to hold carpet in place.
- Take measurements and study floor sketches to calculate the area to be carpeted and the amount of material needed.
- Install carpet on some floors using adhesive, following prescribed method.
- Clean up before and after installation, including vacuuming carpet and discarding remnant pieces.
- Measure, cut and install tackless strips along the baseboard or wall.
- Nail tack strips around area to be carpeted or use old strips to attach edges of new carpet.
- Cut carpet padding to size and install padding, following prescribed method.
- Fasten metal treads across door openings or where carpet meets flooring to hold carpet in place.
- Draw building diagrams and record dimensions.
- Move furniture from area to be carpeted and remove old carpet and padding.
- Cut and bind material.
- Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly.
- Inspect buildings to identify required weatherization measures, including repair work, modification, or replacement.
- Test combustible appliances, such as gas appliances.
- Determine amount of air leakage in buildings, using a blower door machine.
- Test and diagnose air flow systems, using furnace efficiency analysis equipment.
- Install and seal air ducts, combustion air openings, or ventilation openings to improve heating and cooling efficiency.
- Recommend weatherization techniques to clients in accordance with needs and applicable energy regulations, codes, policies, or statutes.
- Apply insulation materials, such as loose, blanket, board, and foam insulation to attics, crawl spaces, basements, or walls.
- Make minor repairs using basic hand or power tools and materials, such as glass, lumber, and drywall.
- Prepare cost estimates or specifications for rehabilitation or weatherization services.
- Contact residents or building owners to schedule appointments.
- Wrap air ducts and water lines with insulating materials, such as duct wrap and pipe insulation.
- Prepare and apply weather-stripping, glazing, caulking, or door sweeps to reduce energy losses.
- Clean and maintain tools and equipment.
- Apply spackling, compounding, or other materials to repair holes in walls.
- Explain recommendations, policies, procedures, requirements, or other related information to residents or building owners.
- Maintain activity logs, financial transaction logs, or other records of weatherization work performed.
- Explain energy conservation measures, such as the use of low flow showerheads and energy-efficient lighting.
- Prepare or assist in the preparation of bids, contracts, or written reports related to weatherization work.
- Install storm windows or storm doors and verify proper fit.
- Wrap water heaters with water heater blankets.
- Inspect buildings to identify required weatherization measures, including repair work, modification, or replacement.
- Inspect problem roofs to determine the best repair procedures.
- Remove snow, water, or debris from roofs prior to applying roofing materials.
- Set up scaffolding to provide safe access to roofs.
- Estimate materials and labor required to complete roofing jobs.
- Cement or nail flashing strips of metal or shingle over joints to make them watertight.
- Install partially overlapping layers of material over roof insulation surfaces, using chalk lines, gauges on shingling hatchets, or lines on shingles.
- Cut felt, shingles, or strips of flashing to fit angles formed by walls, vents, or intersecting roof surfaces.
- Apply plastic coatings, membranes, fiberglass, or felt over sloped roofs before applying shingles.
- Install, repair, or replace single-ply roofing systems, using waterproof sheet materials such as modified plastics, elastomeric, or other asphaltic compositions.
- Attach roofing paper to roofs in overlapping strips to form bases for other materials.
- Cover roofs or exterior walls of structures with slate, asphalt, aluminum, wood, gravel, gypsum, or related materials, using brushes, knives, punches, hammers, or other tools.
- Waterproof or damp-proof walls, floors, roofs, foundations, or basements by painting or spraying surfaces with waterproof coatings or by attaching waterproofing membranes to surfaces.
- Apply reflective roof coatings, such as special paints or single-ply roofing sheets, to existing roofs to reduce solar heat absorption.
- Apply alternate layers of hot asphalt or tar and roofing paper to roofs.
- Install vapor barriers or layers of insulation on flat roofs.
- Cover exposed nailheads with roofing cement or caulking to prevent water leakage or rust.
- Smooth rough spots to prepare surfaces for waterproofing, using hammers, chisels, or rubbing bricks.
- Glaze top layers to make a smooth finish or embed gravel in the bitumen for rough surfaces.
- Mop or pour hot asphalt or tar onto roof bases.
- Install attic ventilation systems, such as turbine vents, gable or ridge vents, or conventional or solar-powered exhaust fans.
- Install skylights on roofs to increase natural light inside structures or to reduce energy costs.
- Apply gravel or pebbles over top layers of roofs, using rakes or stiff-bristled brooms.
- Install solar roofing systems that have energy-collecting photovoltaic panels built into roofing membranes, shingles, or tiles.
- Spray roofs, sidings, or walls to bind, seal, insulate, or soundproof sections of structures, using spray guns, air compressors, or heaters.
- Attach solar panels to existing roofs, according to specifications and without damaging roofing materials or the structural integrity of buildings.
- Punch holes in slate, tile, terra cotta, or wooden shingles, using punches and hammers.
- Apply modular soil- and plant-containing grids over existing roof membranes to create green roofs.
- Install layers of vegetation-based green roofs, including protective membranes, drainage, aeration, water retention and filter layers, soil substrates, irrigation materials, and plants.
- Inspect problem roofs to determine the best repair procedures.
