- Locate problems, using specially designed equipment, and mark where digging must occur to reach damaged tanks or pipes.
Occupations with related tasks Save Table: XLSX CSV
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Disassemble defective units, and repair or replace parts such as locks, gears, cables, and electric wiring.
- Check that safety regulations and building codes are met, and complete service reports verifying conformance to standards.
- Adjust safety controls, counterweights, door mechanisms, and components such as valves, ratchets, seals, and brake linings.
- Read and interpret blueprints to determine the layout of system components, frameworks, and foundations, and to select installation equipment.
- Connect car frames to counterweights, using steel cables.
- Maintain log books that detail all repairs and checks performed.
- Connect electrical wiring to control panels and electric motors.
- Participate in additional training to keep skills up to date.
- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Install outer doors and door frames at elevator entrances on each floor of a structure.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Bolt or weld steel rails to the walls of shafts to guide elevators, working from scaffolding or platforms.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Cut prefabricated sections of framework, rails, and other components to specified dimensions.
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Locate existing pipes needing repair or replacement, using magnetic or radio indicators.
- Install or use instruments such as lasers, grade rods, or transit levels.
- Cut pipes to required lengths.
- Connect pipe pieces and seal joints, using welding equipment, cement, or glue.
- Cover pipes with earth or other materials.
- Install or repair sanitary or stormwater sewer structures or pipe systems.
- Align and position pipes to prepare them for welding or sealing.
- Check slopes for conformance to requirements, using levels or lasers.
- Lay out pipe routes, following written instructions or blueprints and coordinating layouts with supervisors.
- Operate mechanized equipment, such as pickup trucks, rollers, tandem dump trucks, front-end loaders, or backhoes.
- Grade or level trench bases, using tamping machines or hand tools.
- Dig trenches to desired or required depths, by hand or using trenching tools.
- Tap and drill holes into pipes to introduce auxiliary lines or devices.
- Train or supervise others in laying pipe.
- Locate existing pipes needing repair or replacement, using magnetic or radio indicators.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.
- Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.
- Guide cranes to move loads about decks.
- Lay gas and oil pipelines.
- Bolt together pump and engine parts.
- Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.
- Clean trucks used in the fields.
- Bolt or nail together wood or steel framework to erect derricks.
- Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.
- Supply equipment to rig floors as requested and provide assistance to roughnecks.
- Clean up spilled oil by bailing it into barrels.
- Keep pipe deck and main deck areas clean and tidy.
- Dig drainage ditches around wells and storage tanks.
- Cut down and remove trees and brush to clear drill sites, to reduce fire hazards, and to make way for roads to sites.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Locate worn or torn areas in roofs.
- Check to ensure that completed roofs are watertight.
- Sweep and clean roofs to prepare them for the application of new roofing materials.
- Clean work areas and equipment.
- Maintain tools and equipment.
- Cover roofs with layers of roofing felt or asphalt strips before installing tile, slate, or composition materials.
- Remove old roofing materials.
- Unload materials and tools from work trucks, and unroll roofing as directed.
- Set ladders, scaffolds, and hoists in place for taking supplies to roofs.
- Place tiles, nail them to roof boards, and cover nailheads with roofing cement.
- Provide assistance to skilled roofers installing and repairing roofs, flashings, and surfaces.
- Attach roofing paper and composition shingles, using nails.
- Perform emergency leak repairs and general maintenance for a variety of roof types.
- Attach sheets of metal to roof boards or building frameworks when installing metal roofs.
- Hoist tar and roofing materials to roofs, using ropes and pulleys, or carry materials up ladders.
- Apply shingles, gravel, or asphalt over the top layer of tar to protect the roofing material.
- Chop tar into small pieces, and heat chopped tar in kettles.
- Clear drains and downspouts and clean gutters.
- Locate worn or torn areas in roofs.
- Patrol assigned track sections so that damaged or broken track can be located and reported.
- Repair or adjust track switches, using wrenches and replacement parts.
- Weld sections of track together, such as switch points and frogs.
- Observe leveling indicator arms to verify levelness and alignment of tracks.
- Operate single- or multiple-head spike driving machines to drive spikes into ties and secure rails.
- Operate track wrenches to tighten or loosen bolts at joints that hold ends of rails together.
- Cut rails to specified lengths, using rail saws.
- Lubricate machines, change oil, or fill hydraulic reservoirs to specified levels.
- Drill holes through rails, tie plates, or fishplates for insertion of bolts or spikes, using power drills.
- Clean tracks or clear ice or snow from tracks or switch boxes.
- Clean, grade, or level ballast on railroad tracks.
- Raise rails, using hydraulic jacks, to allow for tie removal and replacement.
- Adjust controls of machines that spread, shape, raise, level, or align track, according to specifications.
- Dress and reshape worn or damaged railroad switch points or frogs, using portable power grinders.
- Clean or make minor repairs to machines or equipment.
- Grind ends of new or worn rails to attain smooth joints, using portable grinders.
- Operate single- or multiple-head spike pullers to pull old spikes from ties.
- String and attach wire-guidelines machine to rails so that tracks or rails can be aligned or leveled.
- Engage mechanisms that lay tracks or rails to specified gauges.
- Drive graders, tamping machines, brooms, or ballast spreading machines to redistribute gravel or ballast between rails.
- Drive vehicles that automatically move and lay tracks or rails over sections of track to be constructed, repaired, or maintained.
- Turn wheels of machines, using lever controls, to adjust guidelines for track alignments or grades, following specifications.
- Push controls to close grasping devices on track or rail sections so that they can be raised or moved.
- Operate tie-adzing machines to cut ties and permit insertion of fishplates that hold rails.
- Paint railroad signs, such as speed limits or gate-crossing warnings.
- Spray ties, fishplates, or joints with oil to protect them from weathering.
- Patrol assigned track sections so that damaged or broken track can be located and reported.
- Locate underground services, such as pipes or wires, prior to beginning work.
- Learn and follow safety regulations.
- Take actions to avoid potential hazards or obstructions, such as utility lines, other equipment, other workers, or falling objects.
- Start engines, move throttles, switches, or levers, or depress pedals to operate machines, such as bulldozers, trench excavators, road graders, or backhoes.
- Coordinate machine actions with other activities, positioning or moving loads in response to hand or audio signals from crew members.
- Align machines, cutterheads, or depth gauge makers with reference stakes and guidelines or ground or position equipment, following hand signals of other workers.
- Signal operators to guide movement of tractor-drawn machines.
- Repair and maintain equipment, making emergency adjustments or assisting with major repairs as necessary.
- Load and move dirt, rocks, equipment, or other materials, using trucks, crawler tractors, power cranes, shovels, graders, or related equipment.
- Drive and maneuver equipment equipped with blades in successive passes over working areas to remove topsoil, vegetation, or rocks or to distribute and level earth or terrain.
- Operate tractors or bulldozers to perform such tasks as clearing land, mixing sludge, trimming backfills, or building roadways or parking lots.
- Monitor operations to ensure that health and safety standards are met.
- Connect hydraulic hoses, belts, mechanical linkages, or power takeoff shafts to tractors.
- Select and fasten bulldozer blades or other attachments to tractors, using hitches.
- Operate loaders to pull out stumps, rip asphalt or concrete, rough-grade properties, bury refuse, or perform general cleanup.
- Operate equipment to demolish or remove debris or to remove snow from streets, roads, or parking lots.
- Keep records of material or equipment usage or problems encountered.
- Adjust handwheels and depress pedals to control attachments, such as blades, buckets, scrapers, or swing booms.
- Check fuel supplies at sites to ensure adequate availability.
- Perform specialized work, using equipment, such as pile drivers, dredging rigs, drillers, or concrete pumpers.
- Talk to clients and study instructions, plans, or diagrams to establish work requirements.
- Drive tractor-trailer trucks to move equipment from site to site.
- Push other equipment when extra traction or assistance is required.
- Operate road watering, oiling, or rolling equipment, or street sealing equipment, such as chip spreaders.
- Operate compactors, scrapers, or rollers to level, compact, or cover refuse at disposal grounds.
- Test atmosphere for adequate oxygen or explosive conditions when working in confined spaces.
- Compile cost estimates for jobs.
- Turn valves to control air or water output of compressors or pumps.
- Locate underground services, such as pipes or wires, prior to beginning work.
