- Clean up work areas and remove debris after extraction activities are complete.
Occupations with related tasks Save Table: XLSX CSV
- Clean up spilled oil by bailing it into barrels.
- Keep pipe deck and main deck areas clean and tidy.
- Clean trucks used in the fields.
- Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.
- Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.
- Guide cranes to move loads about decks.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Lay gas and oil pipelines.
- Bolt together pump and engine parts.
- Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.
- Bolt or nail together wood or steel framework to erect derricks.
- Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.
- Supply equipment to rig floors as requested and provide assistance to roughnecks.
- Dig drainage ditches around wells and storage tanks.
- Cut down and remove trees and brush to clear drill sites, to reduce fire hazards, and to make way for roads to sites.
- Clean up spilled oil by bailing it into barrels.
- Keep pipe deck and main deck areas clean and tidy.
- Clean trucks used in the fields.
- Clean work areas and equipment.
- Clear drains and downspouts and clean gutters.
- Sweep and clean roofs to prepare them for the application of new roofing materials.
- Check to ensure that completed roofs are watertight.
- Locate worn or torn areas in roofs.
- Maintain tools and equipment.
- Cover roofs with layers of roofing felt or asphalt strips before installing tile, slate, or composition materials.
- Remove old roofing materials.
- Unload materials and tools from work trucks, and unroll roofing as directed.
- Set ladders, scaffolds, and hoists in place for taking supplies to roofs.
- Place tiles, nail them to roof boards, and cover nailheads with roofing cement.
- Provide assistance to skilled roofers installing and repairing roofs, flashings, and surfaces.
- Attach roofing paper and composition shingles, using nails.
- Perform emergency leak repairs and general maintenance for a variety of roof types.
- Attach sheets of metal to roof boards or building frameworks when installing metal roofs.
- Hoist tar and roofing materials to roofs, using ropes and pulleys, or carry materials up ladders.
- Apply shingles, gravel, or asphalt over the top layer of tar to protect the roofing material.
- Chop tar into small pieces, and heat chopped tar in kettles.
- Clean work areas and equipment.
- Clear drains and downspouts and clean gutters.
- Sweep and clean roofs to prepare them for the application of new roofing materials.
- Clean or prepare construction sites to eliminate possible hazards.
- Lubricate, clean, or repair machinery, equipment, or tools.
- Spray materials, such as water, sand, steam, vinyl, paint, or stucco, through hoses to clean, coat, or seal surfaces.
- Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.
- Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.
- Signal equipment operators to facilitate alignment, movement, or adjustment of machinery, equipment, or materials.
- Read plans, instructions, or specifications to determine work activities.
- Measure, mark, or record openings or distances to layout areas where construction work will be performed.
- Dig ditches or trenches, backfill excavations, or compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, or rakes.
- Load, unload, or identify building materials, machinery, or tools, distributing them to the appropriate locations, according to project plans or specifications.
- Position, join, align, or seal structural components, such as concrete wall sections or pipes.
- Perform site activities required of green certified construction practices, such as implementing waste management procedures, identifying materials for reuse, or installing erosion or sedimentation control mechanisms.
- Control traffic passing near, in, or around work zones.
- Install sewer, water, or storm drain pipes, using pipe-laying machinery or laser guidance equipment.
- Operate or maintain air monitoring or other sampling devices in confined or hazardous environments.
- Smooth or finish freshly poured cement or concrete, using floats, trowels, screeds, or powered cement finishing tools.
- Erect or dismantle scaffolding, shoring, braces, traffic barricades, ramps, or other temporary structures.
- Provide assistance to craft workers, such as carpenters, plasterers, or masons.
- Perform building weatherization tasks, such as repairing windows, adding insulation, or applying weather-stripping materials.
- Apply weather-stripping to reduce energy loss.
- Raze buildings or salvage useful materials.
- Position or dismantle forms for pouring concrete, using saws, hammers, nails, or bolts.
- Grind, scrape, sand, or polish surfaces, such as concrete, marble, terrazzo, or wood flooring, using abrasive tools or machines.
- Place, consolidate, or protect case-in-place concrete or masonry structures.
- Mix ingredients to create compounds for covering or cleaning surfaces.
- Mix, pour, or spread concrete, using portable cement mixers.
- Operate jackhammers or drills to break up concrete or pavement.
- Apply caulking compounds by hand or caulking guns to protect against entry of water or air.
- Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings or walls.
- Identify, pack, or transport hazardous or radioactive materials.
- Use computers or other input devices to control robotic pipe cutters or cleaners.
- Perform construction laborer duties at green building sites, such as renewable energy plants or wind turbine installations.
- Clean or prepare construction sites to eliminate possible hazards.
- Lubricate, clean, or repair machinery, equipment, or tools.
- Spray materials, such as water, sand, steam, vinyl, paint, or stucco, through hoses to clean, coat, or seal surfaces.
- Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.
- Clean installation site, mixing and storage areas, tools, machines, and equipment, and store materials and equipment.
- Wash polished terrazzo surface, using cleaner and water, and apply sealer and curing agent according to manufacturer's specifications, using brush or sprayer.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Measure designated amounts of ingredients for terrazzo or grout, according to standard formulas and specifications, using graduated containers and scales, and load ingredients into portable mixer.
- Grind surfaces with a power grinder, or polish surfaces with polishing or surfacing machines.
- Cut metal division strips and press them into the terrazzo base for joints or changes of color to form designs or patterns or to help prevent cracks.
- Blend marble chip mixtures, place into panels, and push a roller over the surface to embed the chips.
- Modify mixing, grouting, grinding, or cleaning procedures, according to type of installation or material used.
- Spread, level, or smooth concrete or terrazzo mixtures to form bases or finished surfaces, using rakes, shovels, hand or power trowels, hand or power screeds, or floats.
- Grind curved surfaces or areas inaccessible to surfacing machine, such as stairways or cabinet tops, with portable hand grinder.
- Position and secure moisture membrane and wire mesh in preparation for pouring base materials for terrazzo installation.
- Fill slight grinding depressions with matching grout material and hand-trowel for a smooth, uniform surface.
- Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth with a trowel.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Chip, scrape, or grind high spots, ridges, or rough projections to finish concrete, using pneumatic chisel, hand chisel, or other hand tools.
- Mold expansion joints and edges, using edging tools, jointers, or straightedges.
- Move terrazzo installation materials, tools, machines, or work devices to work areas, manually or using wheelbarrow.
- Repair concrete by cutting out damaged areas, drilling holes for reinforcing rods, and positioning reinforcing rods, using power saw and drill.
- Precast terrazzo blocks in wooden forms.
- Wet concrete surface and rub with stone to smooth surface and obtain specified finish.
- Build wooden molds, clamping molds around areas to be repaired, or setting up frames to the proper depth and alignment.
- Spread roofing paper on surface of foundation and spread concrete onto roofing paper with trowel to form terrazzo base.
- Produce rough concrete surface, using broom.
- Remove frames when the foundation is dry.
- Signal truck driver to position truck to facilitate pouring concrete and move chute to direct concrete on forms.
- Clean installation site, mixing and storage areas, tools, machines, and equipment, and store materials and equipment.
- Wash polished terrazzo surface, using cleaner and water, and apply sealer and curing agent according to manufacturer's specifications, using brush or sprayer.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Sweep sand from the surface prior to opening to traffic.
- Prepare base for installation by removing unstable or unsuitable materials, compacting and grading the soil, draining or stabilizing weak or saturated soils and taking measures to prevent water penetration and migration of bedding sand.
- Supply and place base materials, edge restraints, bedding sand and jointing sand.
- Discuss the design with the client.
- Set pavers, aligning and spacing them correctly.
- Sweep sand into the joints and compact pavement until the joints are full.
- Screed sand level to an even thickness, and recheck sand exposed to elements, raking and rescreeding if necessary.
- Cut paving stones to size and for edges, using a splitter and a masonry saw.
- Compact bedding sand and pavers to finish the paved area, using a plate compactor.
- Design paver installation layout pattern and create markings for directional references of joints and stringlines.
- Resurface an outside area with cobblestones, terracotta tiles, concrete or other materials.
- Cement the edges of the paved area.
- Sweep sand from the surface prior to opening to traffic.
- Clean up before and after installation, including vacuuming carpet and discarding remnant pieces.
- Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly.
- Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting.
- Join edges of carpet and seam edges where necessary, by sewing or by using tape with glue and heated carpet iron.
- Cut and trim carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer.
- Plan the layout of the carpet, allowing for expected traffic patterns and placing seams for best appearance and longest wear.
- Stretch carpet to align with walls and ensure a smooth surface, and press carpet in place over tack strips or use staples, tape, tacks or glue to hold carpet in place.
- Take measurements and study floor sketches to calculate the area to be carpeted and the amount of material needed.
- Install carpet on some floors using adhesive, following prescribed method.
- Measure, cut and install tackless strips along the baseboard or wall.
- Nail tack strips around area to be carpeted or use old strips to attach edges of new carpet.
- Cut carpet padding to size and install padding, following prescribed method.
- Fasten metal treads across door openings or where carpet meets flooring to hold carpet in place.
- Draw building diagrams and record dimensions.
- Move furniture from area to be carpeted and remove old carpet and padding.
- Cut and bind material.
- Clean up before and after installation, including vacuuming carpet and discarding remnant pieces.
- Remove handbills within patrol areas.
- Enter and retrieve information pertaining to vehicle registration, identification, and status, using hand-held computers.
- Patrol an assigned area by vehicle or on foot to ensure public compliance with existing parking ordinance.
- Write warnings and citations for illegally parked vehicles.
- Appear in court at hearings regarding contested traffic citations.
- Maintain assigned equipment and supplies, such as hand-held citation computers, citation books, rain gear, tire-marking chalk, and street cones.
- Respond to and make radio dispatch calls regarding parking violations and complaints.
- Maintain close communications with dispatching personnel, using two-way radios or cell phones.
- Perform simple vehicle maintenance procedures, such as checking oil and gas, and report mechanical problems to supervisors.
- Observe and report hazardous conditions, such as missing traffic signals or signs, and street markings that need to be repainted.
- Identify vehicles in violation of parking codes, checking with dispatchers when necessary to confirm identities or to determine whether vehicles need to be booted or towed.
- Train new or temporary staff.
- Make arrangements for illegally parked or abandoned vehicles to be towed, and direct tow-truck drivers to the correct vehicles.
- Investigate and answer complaints regarding contested parking citations, determining their validity and routing them appropriately.
- Provide information to the public regarding parking regulations and facilities, and the location of streets, buildings and points of interest.
- Prepare and maintain required records, including logs of parking enforcement activities, and records of contested citations.
- Perform traffic control duties such as setting up barricades and temporary signs, placing bags on parking meters to limit their use, or directing traffic.
- Mark tires of parked vehicles with chalk and record time of marking, and return at regular intervals to ensure that parking time limits are not exceeded.
- Locate lost, stolen, and counterfeit parking permits, and take necessary enforcement action.
- Collect coins deposited in meters.
- Wind parking meter clocks.
- Provide assistance to motorists needing help with problems, such as flat tires, keys locked in cars, or dead batteries.
- Assign and review the work of subordinates.
- Remove handbills within patrol areas.
- Clean work area and wash parts.
- Strip insulation from wire ends, using wire stripping pliers, and attach wires to terminals for subsequent soldering.
- Trace out short circuits in wiring, using test meter.
- Measure, cut, and bend wire and conduit, using measuring instruments and hand tools.
- Examine electrical units for loose connections and broken insulation and tighten connections, using hand tools.
- Maintain tools, vehicles, and equipment and keep parts and supplies in order.
- Drill holes and pull or push wiring through openings, using hand and power tools.
- Perform semi-skilled and unskilled laboring duties related to the installation, maintenance and repair of a wide variety of electrical systems and equipment.
- Thread conduit ends, connect couplings, and fabricate and secure conduit support brackets, using hand tools.
- Disassemble defective electrical equipment, replace defective or worn parts, and reassemble equipment, using hand tools.
- Construct controllers and panels, using power drills, drill presses, taps, saws, and punches.
- Transport tools, materials, equipment, and supplies to work site by hand, handtruck, or heavy, motorized truck.
- String transmission lines or cables through ducts or conduits, under the ground, through equipment, or to towers.
- Install copper-clad ground rods, using a manual post driver.
- Dig trenches or holes for installation of conduit or supports.
- Raise, lower, or position equipment, tools, and materials, using hoist, hand line, or block and tackle.
- Bolt component parts together to form tower assemblies, using hand tools.
- Erect electrical system components and barricades, and rig scaffolds, hoists, and shoring.
- Trim trees and clear undergrowth along right-of-way.
- Requisition materials, using warehouse requisition or release forms.
- Solder electrical connections, using soldering iron.
- Paint a variety of objects related to electrical functions.
- Break up concrete, using airhammer, to facilitate installation, construction, or repair of equipment.
- Operate heavy equipment, such as backhoes.
- Operate cutting torches and welding equipment, while working with conduit and metal components to construct devices associated with electrical functions.
- Clean work area and wash parts.
- Follow established safety rules and regulations and maintain a safe and clean environment.
- Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
- Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue.
- Study specifications in blueprints, sketches, or building plans to prepare project layout and determine dimensions and materials required.
- Shape or cut materials to specified measurements, using hand tools, machines, or power saws.
- Verify trueness of structure, using plumb bob and level.
- Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.
- Erect scaffolding or ladders for assembling structures above ground level.
- Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.
- Maintain records, document actions, and present written progress reports.
- Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.
- Maintain job records and schedule work crew.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Bore boltholes in timber, masonry or concrete walls, using power drill.
- Install rough door and window frames, subflooring, fixtures, or temporary supports in structures undergoing construction or repair.
- Dig or direct digging of post holes and set poles to support structures.
- Cover subfloors with building paper to keep out moisture and lay hardwood, parquet, or wood-strip-block floors by nailing floors to subfloor or cementing them to mastic or asphalt base.
- Construct forms or chutes for pouring concrete.
- Arrange for subcontractors to deal with special areas, such as heating or electrical wiring work.
- Build or repair cabinets, doors, frameworks, floors, or other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, or power tools.
- Finish surfaces of woodwork or wallboard in houses or buildings, using paint, hand tools, or paneling.
- Select and order lumber or other required materials.
- Work with or remove hazardous material.
- Fill cracks or other defects in plaster or plasterboard and sand patch, using patching plaster, trowel, and sanding tool.
- Prepare cost estimates for clients or employers.
- Perform minor plumbing, welding, or concrete mixing work.
- Apply shock-absorbing, sound-deadening, or decorative paneling to ceilings or walls.
- Examine structural timbers and supports to detect decay, and replace timbers as required, using hand tools, nuts, and bolts.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
- Follow established safety rules and regulations and maintain a safe and clean environment.
