- Turn valves to control air or water output of compressors or pumps.
Occupations with related tasks Save Table: XLSX CSV
- Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.
- Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings or walls.
- Lubricate, clean, or repair machinery, equipment, or tools.
- Signal equipment operators to facilitate alignment, movement, or adjustment of machinery, equipment, or materials.
- Read plans, instructions, or specifications to determine work activities.
- Measure, mark, or record openings or distances to layout areas where construction work will be performed.
- Clean or prepare construction sites to eliminate possible hazards.
- Dig ditches or trenches, backfill excavations, or compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, or rakes.
- Load, unload, or identify building materials, machinery, or tools, distributing them to the appropriate locations, according to project plans or specifications.
- Position, join, align, or seal structural components, such as concrete wall sections or pipes.
- Perform site activities required of green certified construction practices, such as implementing waste management procedures, identifying materials for reuse, or installing erosion or sedimentation control mechanisms.
- Control traffic passing near, in, or around work zones.
- Install sewer, water, or storm drain pipes, using pipe-laying machinery or laser guidance equipment.
- Operate or maintain air monitoring or other sampling devices in confined or hazardous environments.
- Smooth or finish freshly poured cement or concrete, using floats, trowels, screeds, or powered cement finishing tools.
- Erect or dismantle scaffolding, shoring, braces, traffic barricades, ramps, or other temporary structures.
- Provide assistance to craft workers, such as carpenters, plasterers, or masons.
- Spray materials, such as water, sand, steam, vinyl, paint, or stucco, through hoses to clean, coat, or seal surfaces.
- Raze buildings or salvage useful materials.
- Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.
- Position or dismantle forms for pouring concrete, using saws, hammers, nails, or bolts.
- Grind, scrape, sand, or polish surfaces, such as concrete, marble, terrazzo, or wood flooring, using abrasive tools or machines.
- Place, consolidate, or protect case-in-place concrete or masonry structures.
- Mix ingredients to create compounds for covering or cleaning surfaces.
- Mix, pour, or spread concrete, using portable cement mixers.
- Operate jackhammers or drills to break up concrete or pavement.
- Apply caulking compounds by hand or caulking guns to protect against entry of water or air.
- Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.
- Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings or walls.
- Start pumps to operate distilling systems that drain and reclaim dry cleaning solvents.
- Clean fabrics, using vacuums or air hoses.
- Operate extractors and driers, or direct their operation.
- Remove items from washers or dry-cleaning machines, or direct other workers to do so.
- Load articles into washers or dry-cleaning machines, or direct other workers to perform loading.
- Sort and count articles removed from dryers, and fold, wrap, or hang them.
- Start washers, dry cleaners, driers, or extractors, and turn valves or levers to regulate machine processes and the volume of soap, detergent, water, bleach, starch, and other additives.
- Examine and sort into lots articles to be cleaned, according to color, fabric, dirt content, and cleaning technique required.
- Clean machine filters, and lubricate equipment.
- Determine spotting procedures and proper solvents, based on fabric and stain types.
- Sprinkle chemical solvents over stains, and pat areas with brushes or sponges to remove stains.
- Inspect soiled articles to determine sources of stains, to locate color imperfections, and to identify items requiring special treatment.
- Apply chemicals to neutralize the effects of solvents.
- Receive and mark articles for laundry or dry cleaning with identifying code numbers or names, using hand or machine markers.
- Apply bleaching powders to spots and spray them with steam to remove stains from fabrics that do not respond to other cleaning solvents.
- Operate machines that comb, dry and polish furs, clean, sterilize and fluff feathers and blankets, or roll and package towels.
- Pre-soak, sterilize, scrub, spot-clean, and dry contaminated or stained articles, using neutralizer solutions and portable machines.
- Mix and add detergents, dyes, bleaches, starches, and other solutions and chemicals to clean, color, dry, or stiffen articles.
- Wash, dry-clean, or glaze delicate articles or fur garment linings by hand, using mild detergents or dry cleaning solutions.
- Match sample colors, applying knowledge of bleaching agent and dye properties, and types, construction, conditions, and colors of articles.
- Operate dry-cleaning machines to clean soiled articles.
- Iron or press articles, fabrics, and furs, using hand irons or pressing machines.
- Hang curtains, drapes, blankets, pants, and other garments on stretch frames to dry.
- Spray steam, water, or air over spots to flush out chemicals, dry material, raise naps, or brighten colors.
- Mend and sew articles, using hand stitching, adhesive patches, or sewing machines.
- Dye articles to change or restore their colors, using knowledge of textile compositions and the properties and effects of bleaches and dyes.
- Test fabrics in inconspicuous places to determine whether solvents will damage dyes or fabrics.
- Mix bleaching agents with hot water in vats, and soak material until it is bleached.
- Rinse articles in water and acetic acid solutions to remove excess dye and to fix colors.
- Immerse articles in bleaching baths to strip colors.
- Identify articles' fabrics and original dyes by sight and touch, or by testing samples with fire or chemical reagents.
- Spread soiled articles on work tables, and position stained portions over vacuum heads or on marble slabs.
- Deliver clean linens and clothes to clients.
- Receive supply deliveries and stock items in storage rooms.
- Start pumps to operate distilling systems that drain and reclaim dry cleaning solvents.
- Clean fabrics, using vacuums or air hoses.
- Start pumps that circulate mud through drill pipes and boreholes to cool drill bits and flush out drill cuttings.
- Control the viscosity and weight of the drilling fluid.
- Listen to mud pumps and check regularly for vibration and other problems to ensure that rig pumps and drilling mud systems are working properly.
- Inspect derricks, or order their inspection, prior to being raised or lowered.
- Prepare mud reports, and instruct crews about the handling of any chemical additives.
- Position and align derrick elements, using harnesses and platform climbing devices.
- Inspect derricks for flaws, and clean and oil derricks to maintain proper working conditions.
- Supervise crew members, and provide assistance in training them.
- Repair pumps, mud tanks, and related equipment.
- Steady pipes during connection to or disconnection from drill or casing strings.
- Weigh clay, and mix with water and chemicals to make drilling mud, using portable mixers.
- Guide lengths of pipe into and out of elevators.
- Clamp holding fixtures on ends of hoisting cables.
- String cables through pulleys and blocks.
- Set and bolt crown blocks to posts at tops of derricks.
- Start pumps that circulate mud through drill pipes and boreholes to cool drill bits and flush out drill cuttings.
- Operate pumps that circulate water, oil, or other fluids through wells to remove sand or other materials obstructing the free flow of oil.
- Maintain and perform safety inspections on equipment and tools.
- Operate controls that raise derricks or level rigs.
- Listen to engines, rotary chains, or other equipment to detect faulty operations or unusual well conditions.
- Prepare reports of services rendered, tools used, or time required, for billing purposes.
- Install pressure-control devices onto wellheads.
- Confer with others to gather information regarding pipe or tool sizes or borehole conditions in wells.
- Drive truck-mounted units to well sites.
- Interpret instrument readings to ascertain the depth of obstruction.
- Thread cables through derrick pulleys, using hand tools.
- Select fishing methods or tools for removing obstacles such as liners, broken casing, screens, or drill pipe.
- Close and seal wells no longer in use.
- Direct drilling crews performing activities such as assembling and connecting pipe, applying weights to drill pipes, or drilling around lodged obstacles.
- Apply green technologies or techniques, such as the use of coiled tubing, slim-hole drilling, horizontal drilling, hydraulic fracturing, or gas lift systems.
- Operate specialized equipment to remove obstructions by backing off or severing pipes by chemical or explosive action.
- Perforate well casings or sidewalls of boreholes with explosive charges.
- Examine unserviceable wells to determine actions to be taken to improve well conditions.
- Monitor sound wave-generating or detecting mechanisms to determine well fluid levels.
- Insert detection instruments into wells with obstructions.
- Operate pumps that circulate water, oil, or other fluids through wells to remove sand or other materials obstructing the free flow of oil.
- Start and examine operation of slush pumps to ensure circulation and consistency of drilling fluid or mud in well.
- Train crews, and introduce procedures to make drill work more safe and effective.
- Observe pressure gauge and move throttles and levers to control the speed of rotary tables, and to regulate pressure of tools at bottoms of boreholes.
- Maintain records of footage drilled, location and nature of strata penetrated, materials and tools used, services rendered, and time required.
- Push levers and brake pedals to control gasoline, diesel, electric, or steam draw works that lower and raise drill pipes and casings in and out of wells.
- Connect sections of drill pipe, using hand tools and powered wrenches and tongs.
- Count sections of drill rod to determine depths of boreholes.
- Maintain and adjust machinery to ensure proper performance.
- Direct rig crews in drilling and other activities, such as setting up rigs and completing or servicing wells.
- Weigh clay, and mix with water and chemicals to make drilling mud.
- Clean and oil pulleys, blocks, and cables.
- Monitor progress of drilling operations, and select and change drill bits according to the nature of strata, using hand tools.
- Repair or replace defective parts of machinery, such as rotary drill rigs, water trucks, air compressors, and pumps, using hand tools.
- Locate and recover lost or broken bits, casings, and drill pipes from wells, using special tools.
- Line drilled holes with pipes, and install all necessary hardware, to prepare new wells.
- Cap wells with packers, or turn valves, to regulate outflow of oil from wells.
- Remove core samples during drilling to determine the nature of the strata being drilled.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Plug observation wells, and restore sites.
- Position and prepare truck-mounted derricks at drilling areas specified on field maps.
- Lower and explode charges in boreholes to start flow of oil from wells.
- Inspect safety equipment, such as harnesses, belts, and lifelines, before use.
- Start and examine operation of slush pumps to ensure circulation and consistency of drilling fluid or mud in well.
- Start pumps to circulate water and abrasives onto blades or cables during cutting.
- Remove defective or substandard materials from machines, and readjust machine components so that products meet standards.
- Maintain production records, such as quantities, types, and dimensions of materials produced.
- Start machines to verify setups, and make any necessary adjustments.
- Press buttons, pull levers, or depress pedals to start and operate cutting and slicing machines.
- Review work orders, blueprints, specifications, or job samples to determine components, settings, and adjustments for cutting and slicing machines.
- Adjust machine controls to alter position, alignment, speed, or pressure.
- Examine, measure, and weigh materials or products to verify conformance to specifications, using measuring devices, such as rulers, micrometers, or scales.
- Remove completed materials or products from cutting or slicing machines, and stack or store them for additional processing.
- Stack and sort cut material for packaging, further processing, or shipping, according to types and sizes of material.
- Type instructions on computer keyboards, push buttons to activate computer programs, or manually set cutting guides, clamps, and knives.
- Select and install machine components, such as cutting blades, rollers, and templates, according to specifications, using hand tools.
- Position stock along cutting lines, or against stops on beds of scoring or cutting machines.
- Monitor operation of cutting or slicing machines to detect malfunctions or to determine whether supplies need replenishment.
- Feed stock into cutting machines, onto conveyors, or under cutting blades, by threading, guiding, pushing, or turning handwheels.
- Move stock or scrap to and from machines manually, or by using carts, handtrucks, or lift trucks.
- Change or replace saw blades, cables, cutter heads, and grinding wheels, using hand tools.
- Clean and lubricate cutting machines, conveyors, blades, saws, or knives, using steam hoses, scrapers, brushes, or oil cans.
- Set up, operate, or tend machines that cut or slice materials, such as glass, stone, cork, rubber, tobacco, food, paper, or insulating material.
- Mark cutting lines or identifying information on stock, using marking pencils, rulers, or scribes.
- Direct workers on cutting teams.
- Operate cranes, or signal crane operators to position or remove stone from cars or saw beds.
- Tighten pulleys or add abrasives to maintain cutting speeds.
- Position width gauge blocks between blades, and level blades and insert wedges into frames to secure blades to frames.
- Sharpen cutting blades, knives, or saws, using files, bench grinders, or honing stones.
- Cut stock manually to prepare for machine cutting, using tools such as knives, cleavers, handsaws, or hammers and chisels.
- Turn cranks or press buttons to activate winches that move cars under sawing cables or saw frames.
- Wash stones, using water hoses.
- Start pumps to circulate water and abrasives onto blades or cables during cutting.
- Pour water into wells, or pump water or slush into wells to cool drill bits and to remove drillings.
- Operate controls to stabilize machines and to position and align drills.
- Start, stop, and control drilling speed of machines and insertion of casings into holes.
- Regulate air pressure, rotary speed, and downward pressure, according to the type of rock or concrete being drilled.
- Select and attach drill bits and drill rods, adding more rods as hole depths increase, and changing drill bits as needed.
- Drive or guide truck-mounted equipment into position, level and stabilize rigs, and extend telescoping derricks.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Verify depths and alignments of boring positions.
- Perform routine maintenance and upgrade work on machines and equipment, such as replacing parts, building up drill bits, and lubricating machinery.
- Select the appropriate drill for the job, using knowledge of rock or soil conditions.
- Document geological formations encountered during work.
- Drive trucks, tractors, or truck-mounted drills to and from work sites.
- Assemble and position machines, augers, casing pipes, and other equipment, using hand and power tools.
- Record drilling progress and geological data.
- Retrieve lost equipment from bore holes, using retrieval tools and equipment.
- Fabricate well casings.
- Create and lay out designs for drill and blast patterns.
- Place and install screens, casings, pumps, and other well fixtures to develop wells.
- Operate water-well drilling rigs and other equipment to drill, bore, and dig for water wells or for environmental assessment purposes.
- Review client requirements and proposed locations for drilling operations to determine feasibility, and to determine cost estimates.
- Drill or bore holes in rock for blasting, grouting, anchoring, or building foundations.
- Perform pumping tests to assess well performance.
- Disinfect, reconstruct, and redevelop contaminated wells and water pumping systems, and clean and disinfect new wells in preparation for use.
- Design well pumping systems.
- Signal crane operators to move equipment.
- Withdraw drill rods from holes, and extract core samples.
- Inspect core samples to determine nature of strata, or take samples to laboratories for analysis.
- Retract augers to force discharge dirt from holes.
- Monitor drilling operations, by checking gauges and listening to equipment to assess drilling conditions and to determine the need to adjust drilling or alter equipment.
- Pour water into wells, or pump water or slush into wells to cool drill bits and to remove drillings.
- Operate motorized pumps to remove water from flooded manholes, basements, or facility floors.
- Shut off steam, water, or other gases or liquids from pipe sections, using valve keys or wrenches.
- Install underground storm, sanitary, or water piping systems, extending piping as needed to connect fixtures and plumbing.
- Assemble pipe sections, tubing, or fittings, using couplings, clamps, screws, bolts, cement, plastic solvent, caulking, or soldering, brazing, or welding equipment.
- Locate and mark the position of pipe installations, connections, passage holes, or fixtures in structures, using measuring instruments such as rulers or levels.
- Cut, thread, or hammer pipes to specifications, using tools such as saws, cutting torches, pipe threaders, or pipe benders.
- Lay out full scale drawings of pipe systems, supports, or related equipment, according to blueprints.
- Plan pipe system layout, installation, or repair, according to specifications.
- Review blueprints, building codes, or specifications to determine work details or procedures.
- Select pipe sizes, types, or related materials, such as supports, hangers, or hydraulic cylinders, according to specifications.
- Fill pipes or plumbing fixtures with water or air and observe pressure gauges to detect and locate leaks.
- Direct helpers engaged in pipe cutting, preassembly, or installation of plumbing systems or components.
- Inspect, examine, or test installed systems or pipe lines, using pressure gauge, hydrostatic testing, observation, or other methods.
- Install pipe assemblies, fittings, valves, appliances such as dishwashers or water heaters, or fixtures such as sinks or toilets, using hand or power tools.
- Anchor steel supports from ceiling joists to hold pipes in place.
- Attach pipes to walls, structures, or fixtures, such as radiators or tanks, using brackets, clamps, tools, or welding equipment.
- Modify, clean, or maintain pipe systems, units, fittings, or related machines or equipment, using hand or power tools.
- Install automatic controls to regulate pipe systems.
- Estimate time, material, or labor costs for use in project plans.
- Keep records of work assignments.
- Inspect structures to assess material or equipment needs, to establish the sequence of pipe installations, or to plan installation around obstructions, such as electrical wiring.
- Maintain or repair plumbing by replacing defective washers, replacing or mending broken pipes, or opening clogged drains.
- Repair or remove and replace system components.
- Cut openings in structures to accommodate pipes or pipe fittings, using hand or power tools.
- Install green plumbing equipment, such as faucet flow restrictors, dual-flush or pressure-assisted flush toilets, or tankless hot water heaters.
- Inspect work sites for obstructions or holes that could cause structural weakness.
- Install pipe systems to support alternative energy-fueled systems, such as geothermal heating or cooling systems.
- Install fixtures, appliances, or equipment designed to reduce water or energy consumption.
- Repair hydraulic or air pumps.
- Weld small pipes or special piping, using specialized techniques, equipment, or materials, such as computer-assisted welding or microchip fabrication.
- Operate motorized pumps to remove water from flooded manholes, basements, or facility floors.
