- Position safety jacks to support underground mine roofs until bolts can be installed.
Occupations with related tasks Save Table: XLSX CSV
- Place safety cones around blast areas to alert other workers of danger zones, and signal workers as necessary to ensure that they clear blast sites prior to explosions.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Lower perforating guns into wells, using hoists; then use measuring devices and instrument panels to position guns in correct positions for taking samples.
- Examine blast areas to determine amounts and kinds of explosive charges needed and to ensure that safety laws are observed.
- Tie specified lengths of delaying fuses into patterns in order to time sequences of explosions.
- Place explosive charges in holes or other spots; then detonate explosives to demolish structures or to loosen, remove, or displace earth, rock, or other materials.
- Insert, pack, and pour explosives, such as dynamite, ammonium nitrate, black powder, or slurries into blast holes; then shovel drill cuttings, admit water into boreholes, and tamp material to compact charges.
- Mark patterns, locations, and depths of charge holes for drilling, and issue drilling instructions.
- Compile and keep gun and explosives records in compliance with local and federal laws.
- Measure depths of drilled blast holes, using weighted tape measures.
- Connect electrical wire to primers, and cover charges or fill blast holes with clay, drill chips, sand, or other material.
- Lay primacord between rows of charged blast holes, and tie cord into main lines to form blast patterns.
- Verify detonation of charges by observing control panels, or by listening for the sounds of blasts.
- Move and store inventories of explosives, loaded perforating guns, and other materials, according to established safety procedures.
- Light fuses, drop detonating devices into wells or boreholes, or activate firing devices with plungers, dials, or buttons, in order to set off single or multiple blasts.
- Drive trucks to transport explosives and blasting equipment to blasting sites.
- Cut specified lengths of primacord and attach primers to cord ends.
- Maintain inventory levels, ordering new supplies as necessary.
- Repair and service blasting, shooting, and automotive equipment, and electrical wiring and instruments, using hand tools.
- Set up and operate short-wave radio or field telephone equipment to transmit and receive blast information.
- Insert waterproof sealers, bullets, and/or powder charges into guns, and screw gun ports back into place.
- Clean, gauge, and lubricate gun ports.
- Connect gun chambers to electric detonating devices, and operate controls at panelboards, in order to detonate charges in guns or to ignite chemical charges.
- Insert powder charges into chambers of sidewall sample-taking cylinders, and assemble cylinders, using special wrenches.
- Obtain samples of earth from sidewalls of well boreholes, using electrically exploding devices.
- Create and lay out designs for drill and blast patterns.
- Document geological formations encountered during work.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Set up and operate equipment such as hoists, jackhammers, and drills, in order to bore charge holes.
- Signal crane operators to move equipment.
- Place safety cones around blast areas to alert other workers of danger zones, and signal workers as necessary to ensure that they clear blast sites prior to explosions.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Lower perforating guns into wells, using hoists; then use measuring devices and instrument panels to position guns in correct positions for taking samples.
- Position safety jacks to support underground mine roofs until bolts can be installed.
- Position bolting machines, and insert drill bits into chucks.
- Drill bolt holes into roofs at specified distances from ribs or adjacent bolts.
- Pull down loose rock that cannot be supported.
- Perform safety checks on equipment before operating.
- Perform tests to determine if methane gas is present.
- Force bolts into holes, using hydraulic mechanisms of self-propelled bolting machines.
- Perform ventilation tasks, such as hanging ventilation curtains and tubes.
- Dust rocks after bolting.
- Install various types of bolts, including truss, glue, and resin bolts, traversing entire ceiling spans.
- Drill test holes and test bolts for specified tension, using torque wrenches.
- Rotate chucks to turn bolts and open expansion heads against rock formations.
- Remove drill bits from chucks after drilling holes, and insert bolts into chucks.
- Tighten ends of anchored truss bolts, using turnbuckles.
- Position safety jacks to support underground mine roofs until bolts can be installed.
- Position bolting machines, and insert drill bits into chucks.
- Hang ventilation tubing and ventilation curtains to ensure that the mining face area is kept properly ventilated.
- Reposition machines to make additional holes or cuts.
- Conduct methane gas checks to ensure breathing quality of air.
- Check the stability of roof and rib support systems before mining face areas.
- Operate mining machines to gather coal and convey it to floors or shuttle cars.
- Drive machines into position at working faces.
- Move controls to start and regulate movement of conveyors and to start and position drill cutters or torches.
- Determine locations, boundaries, and depths of holes or channels to be cut.
- Observe and listen to equipment operation to detect binding or stoppage of tools or other equipment malfunctions.
- Repair, oil, and adjust machines, and change cutting teeth, using wrenches.
- Install casings to prevent cave-ins.
- Scrape or wash conveyors, using belt scrapers or belt washers, to minimize dust production.
- Move levers to raise and lower hydraulic safety bars supporting roofs above machines until other workers complete framing.
- Apply new technologies developed to minimize the environmental impact of coal mining.
- Guide and assist crews laying track and resetting supports and blocking.
- Hang ventilation tubing and ventilation curtains to ensure that the mining face area is kept properly ventilated.
- Reposition machines to make additional holes or cuts.
- Dig or direct digging of post holes and set poles to support structures.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Follow established safety rules and regulations and maintain a safe and clean environment.
- Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
- Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue.
- Study specifications in blueprints, sketches, or building plans to prepare project layout and determine dimensions and materials required.
- Shape or cut materials to specified measurements, using hand tools, machines, or power saws.
- Verify trueness of structure, using plumb bob and level.
- Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.
- Erect scaffolding or ladders for assembling structures above ground level.
- Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.
- Maintain records, document actions, and present written progress reports.
- Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.
- Maintain job records and schedule work crew.
- Bore boltholes in timber, masonry or concrete walls, using power drill.
- Install rough door and window frames, subflooring, fixtures, or temporary supports in structures undergoing construction or repair.
- Cover subfloors with building paper to keep out moisture and lay hardwood, parquet, or wood-strip-block floors by nailing floors to subfloor or cementing them to mastic or asphalt base.
- Construct forms or chutes for pouring concrete.
- Arrange for subcontractors to deal with special areas, such as heating or electrical wiring work.
- Build or repair cabinets, doors, frameworks, floors, or other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, or power tools.
- Finish surfaces of woodwork or wallboard in houses or buildings, using paint, hand tools, or paneling.
- Select and order lumber or other required materials.
- Work with or remove hazardous material.
- Fill cracks or other defects in plaster or plasterboard and sand patch, using patching plaster, trowel, and sanding tool.
- Prepare cost estimates for clients or employers.
- Perform minor plumbing, welding, or concrete mixing work.
- Apply shock-absorbing, sound-deadening, or decorative paneling to ceilings or walls.
- Examine structural timbers and supports to detect decay, and replace timbers as required, using hand tools, nuts, and bolts.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
- Dig or direct digging of post holes and set poles to support structures.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Place blocks under rebar to hold the bars off the deck when reinforcing floors.
- Determine quantities, sizes, shapes, and locations of reinforcing rods from blueprints, sketches, or oral instructions.
- Space and fasten together rods in forms according to blueprints, using wire and pliers.
- Position and secure steel bars, rods, cables, or mesh in concrete forms, using fasteners, rod-bending machines, blowtorches, or hand tools.
- Cut rods to required lengths, using metal shears, hacksaws, bar cutters, or acetylene torches.
- Cut and fit wire mesh or fabric, using hooked rods, and position fabric or mesh in concrete to reinforce concrete.
- Bend steel rods with hand tools or rod-bending machines and weld them with arc-welding equipment.
- Place blocks under rebar to hold the bars off the deck when reinforcing floors.
- Distribute traffic control signs and markers at designated points.
- Direct or escort pedestrians across streets, stopping traffic, as necessary.
- Guide or control vehicular or pedestrian traffic at such places as street and railroad crossings and construction sites.
- Monitor traffic flow to locate safe gaps through which pedestrians can cross streets.
- Communicate traffic and crossing rules and other information to students and adults.
- Direct traffic movement or warn of hazards, using signs, flags, lanterns, and hand signals.
- Report unsafe behavior of children to school officials.
- Record license numbers of vehicles disregarding traffic signals, and report infractions to appropriate authorities.
- Stop speeding vehicles to warn drivers of traffic laws.
- Learn the location and purpose of street traffic signs within assigned patrol areas.
- Discuss traffic routing plans and control-point locations with superiors.
- Inform drivers of detour routes through construction sites.
- Distribute traffic control signs and markers at designated points.
- Set up scaffolding or cranes to assist with setting up of lighting equipment.
- Assess safety of wiring or equipment set-up to determine the risk of fire or electrical shock.
- Consult with lighting director or production staff to determine lighting requirements.
- Disassemble and store equipment after performances.
- Install color effects or image patterns, such as color filters, onto lighting fixtures.
- Install electrical cables or wire fixtures.
- Load, unload, or position lighting equipment.
- Match light fixture settings, such as brightness and color, to lighting design plans.
- Notify supervisors when major lighting equipment repairs are needed.
- Operate manual or automated systems to control lighting throughout productions.
- Patch or wire lights to dimmers or other electronic consoles.
- Perform minor repairs or routine maintenance on lighting equipment, such as replacing lamps or damaged color filters.
- Program lighting consoles or load automated lighting control systems onto consoles.
- Set up and focus light fixtures to meet requirements of television, theater, concerts, or other productions.
- Test lighting equipment function and desired lighting effects.
- Visit and assess structural and electrical layout of locations before setting up lighting equipment.
- Set up scaffolding or cranes to assist with setting up of lighting equipment.
- Place blocks under reinforcing bars used to reinforce floors.
- Read specifications or blueprints to determine the locations, quantities, or sizes of materials required.
- Connect columns, beams, and girders with bolts, following blueprints and instructions from supervisors.
- Bolt aligned structural steel members in position for permanent riveting, bolting, or welding into place.
- Fasten structural steel members to hoist cables, using chains, cables, or rope.
- Hoist steel beams, girders, or columns into place, using cranes or signaling hoisting equipment operators to lift and position structural steel members.
- Verify vertical and horizontal alignment of structural steel members, using plumb bobs, laser equipment, transits, or levels.
- Cut, bend, or weld steel pieces, using metal shears, torches, or welding equipment.
- Erect metal or precast concrete components for structures, such as buildings, bridges, dams, towers, storage tanks, fences, or highway guard rails.
- Force structural steel members into final positions, using turnbuckles, crowbars, jacks, or hand tools.
- Pull, push, or pry structural steel members into approximate positions for bolting into place.
- Unload and position prefabricated steel units for hoisting, as needed.
- Drive drift pins through rivet holes to align rivet holes in structural steel members with corresponding holes in previously placed members.
- Assemble hoisting equipment or rigging, such as cables, pulleys, or hooks, to move heavy equipment or materials.
- Fabricate metal parts, such as steel frames, columns, beams, or girders, according to blueprints or instructions from supervisors.
- Dismantle structures or equipment.
- Ride on girders or other structural steel members to position them, or use rope to guide them into position.
- Hold rivets while riveters use air hammers to form heads on rivets.
- Insert sealing strips, wiring, insulating material, ladders, flanges, gauges, or valves, depending on types of structures being assembled.
- Catch hot rivets in buckets and insert rivets in holes, using tongs.
- Place blocks under reinforcing bars used to reinforce floors.