- Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.
Occupations with related tasks Save Table: XLSX CSV
- Pour compounds into transformer-case terminal openings to seal out moisture.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Set machinery for proper performance, using computers.
- Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Lift units or parts such as motors or generators, using cranes or chain hoists, or signal crane operators to lift heavy parts or subassemblies.
- Record repairs required, parts used, and labor time.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Lubricate moving parts.
- Read service guides to find information needed to perform repairs.
- Inspect electrical connections, wiring, relays, charging resistance boxes, and storage batteries, following wiring diagrams.
- Scrape and clean units or parts, using cleaning solvents and equipment such as buffing wheels.
- Weld, braze, or solder electrical connections.
- Steam-clean polishing and buffing wheels to remove abrasives and bonding materials, and spray, brush, or recoat surfaces as necessary.
- Test equipment for overheating, using speed gauges and thermometers.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Maintain stocks of parts.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Solder, wrap, and coat wires to ensure proper insulation.
- Rewire electrical systems, and repair or replace electrical accessories.
- Clean cells, cell assemblies, glassware, leads, electrical connections, and battery poles, using scrapers, steam, water, emery cloths, power grinders, or acid.
- Rewind coils on cores in slots, or make replacement coils, using coil-winding machines.
- Test conditions, fluid levels, and specific gravities of electrolyte cells, using voltmeters, hydrometers, and thermometers.
- Add water or acid to battery cell solutions to obtain specified concentrations.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Hammer out dents and twists in tools and equipment.
- Drain and filter transformer oil and refill transformers with oil until coils are submerged.
- Repair and operate battery-charging equipment.
- Sharpen tools such as saws, picks, shovels, screwdrivers, and scoops, either manually or by using bench grinders and emery wheels.
- Inspect batteries for structural defects such as dented cans, damaged carbon rods and terminals, and defective seals.
- Test battery charges, and replace or recharge batteries as necessary.
- Bolt porcelain insulators to wood parts to assemble hot stools.
- Position and level battery cells, anodes, or cathodes, using hoists or leveling jacks, or signal other workers to perform positioning and leveling.
- Clean, rinse, and dry transformer cases, using boiling water, scrapers, solvents, hoses, and cloths.
- Pour compounds into transformer-case terminal openings to seal out moisture.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Set machinery for proper performance, using computers.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- Connect electrical systems to outside power sources and activate switches to test the operation of appliances and light fixtures.
- Move and set up mobile homes or prefabricated buildings on owners' lots or at mobile home parks.
- Inspect, examine, and test the operation of parts or systems to evaluate operating condition and to determine if repairs are needed.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of plumbing fixtures.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, and diagrams.
- Confer with customers or read work orders to determine the nature and extent of damage to units.
- Install, repair, and replace units, fixtures, appliances, and other items and systems in mobile and modular homes, prefabricated buildings, or travel trailers, using hand tools or power tools.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Repair leaks in plumbing or gas lines, using caulking compounds and plastic or copper pipe.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, and hand tools.
- Open and close doors, windows, and drawers to test their operation, trimming edges to fit, using jackplanes or drawknives.
- Refinish wood surfaces on cabinets, doors, moldings, and floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- Connect electrical systems to outside power sources and activate switches to test the operation of appliances and light fixtures.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Calibrate instrumentation, such as meters, gauges, and regulators, for pressure, temperature, flow, and level.
- Turn meters on or off to establish or close service.
- Shut off service and notify repair crews when major repairs are required, such as the replacement of underground pipes or wiring.
- Turn valves to allow measured amounts of air or gas to pass through meters at specified flow rates.
- Vary air pressure flowing into regulators and turn handles to assess functioning of valves and pistons.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Make adjustments to meter components, such as setscrews or timing mechanisms, so that they conform to specifications.
- Calibrate thermostats for specified temperature or pressure settings.
- Record maintenance information, including test results, material usage, and repairs made.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Lubricate wearing surfaces of mechanical parts, using oils or other lubricants.
- Install, inspect and test electric meters, relays, and power sources to detect causes of malfunctions and inaccuracies, using hand tools and testing equipment.
- Test valves and regulators for leaks and accurate temperature and pressure settings, using precision testing equipment.
- Record meter readings and installation data on meter cards, work orders, or field service orders, or enter data into hand-held computers.
- Install regulators and related equipment such as gas meters, odorization units, and gas pressure telemetering equipment.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Report hazardous field situations and damaged or missing meters.
- Examine valves or mechanical control device parts for defects, dents, or loose attachments, and mark malfunctioning areas of defective units.
- Mount and install meters and other electric equipment such as time clocks, transformers, and circuit breakers, using electricians' hand tools.
- Investigate instances of illegal tapping into service lines.
- Trace and tag meters or house lines.
- Repair electric meters and components, such as transformers and relays, and replace metering devices, dial glasses, and faulty or incorrect wiring, using hand tools.
- Replace defective parts, such as bellows, range springs, and toggle switches, and reassemble units according to blueprints, using cam presses and hand tools.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Measure tolerances of assembled and salvageable parts for conformance to standards or specifications, using gauges, micrometers, and calipers.
- Clean internal compartments and moving parts, using rags and cleaning compounds.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Reassemble repaired equipment, and solder top, front, and back case panels in place, using soldering guns, power tools, and hand tools.
- Attach air hoses to meter inlets, plug outlets, and observe gauges for pressure losses to test internal seams for leaks.
- Recommend and write up specifications for changes in hardware, such as house wiring.
- Clamp regulator units into vises on stages above water tanks, and attach compressed air hoses to intake ports.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Collect money due on delinquent accounts.
- Splice and connect cables from meters or current transformers to pull boxes or switchboards, using hand tools.
- Attach pressurized meters to fixtures which submerge them in water, and observe meters for leaks.
- Advise customers on proper installation of valves or regulators and related equipment.
- Clean plant growth, scale, paint, soil, or rust from meter housings, using wire brushes, scrapers, buffers, sandblasters, or cleaning compounds.
- Connect hoses from provers to meter inlets and outlets, and raise prover bells until prover gauges register zero.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Calibrate instrumentation, such as meters, gauges, and regulators, for pressure, temperature, flow, and level.
- Turn meters on or off to establish or close service.
- Shut off service and notify repair crews when major repairs are required, such as the replacement of underground pipes or wiring.
- Turn valves to allow measured amounts of air or gas to pass through meters at specified flow rates.
- Vary air pressure flowing into regulators and turn handles to assess functioning of valves and pistons.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Make adjustments to meter components, such as setscrews or timing mechanisms, so that they conform to specifications.
- Calibrate thermostats for specified temperature or pressure settings.
- Turn setscrews to adjust receivers for maximum sensitivity and transmitters for maximum output.
- Check antenna positioning to ensure specified azimuths or mechanical tilts and adjust as necessary.
- Calibrate and align components, using scales, gauges, and other measuring instruments.
- Insert plugs into receptacles and bolt or screw leads to terminals to connect equipment to power sources, using hand tools.
- Install, adjust, and repair stationary and mobile radio transmitting and receiving equipment and two-way radio communication systems.
- Monitor radio range stations to detect transmission flaws and adjust controls to eliminate flaws.
- Inspect completed work to ensure all hardware is tight, antennas are level, hangers are properly fastened, proper support is in place, or adequate weather proofing has been installed.
- Run appropriate power, ground, or coaxial cables.
- Test operation of tower transmission components, using sweep testing tools or software.
- Install all necessary transmission equipment components, including antennas or antenna mounts, surge arrestors, transmission lines, connectors, or tower-mounted amplifiers (TMAs).
- Read work orders, blueprints, plans, datasheets or site drawings to determine work to be done.
- Replace existing antennas with new antennas as directed.
- Bolt equipment into place, using hand or power tools.
- Install, connect, or test underground or aboveground grounding systems.
- Complete reports related to project status, progress, or other work details, using computer software.
- Transport equipment to work sites, using utility trucks and equipment trailers.
- Take site survey photos or photos of work performed, using digital cameras.
- Climb towers to access components, using safety equipment, such as full-body harnesses.
- Climb communication towers to install, replace, or repair antennas or auxiliary equipment used to transmit and receive radio waves.
- Lift equipment into position, using cranes and rigging tools or equipment, such as gin poles.
- Perform maintenance or repair work on existing tower equipment, using hand or power tools.
- Locate tower sites where work is to be performed, using mapping software.
- Install or repair tower lighting components, including strobes, beacons, or lighting controllers.
- Examine malfunctioning radio equipment to locate defects such as loose connections, broken wires, or burned-out components, using schematic diagrams and test equipment.
- Mount equipment on transmission towers and in vehicles such as ships or ambulances.
- Remove and replace defective components and parts such as conductors, resistors, semiconductors, and integrated circuits, using soldering irons, wire cutters, and hand tools.
- Repair circuits, wiring, and soldering, using soldering irons and hand tools to install parts and adjust connections.
- Test batteries, using hydrometers and ammeters, and charge batteries as necessary.
- Test emergency transmitters to ensure their readiness for immediate use.
- Test equipment functions such as signal strength and quality, transmission capacity, interference, and signal delay, using equipment such as oscilloscopes, circuit analyzers, frequency meters, and wattmeters.
- Turn setscrews to adjust receivers for maximum sensitivity and transmitters for maximum output.
- Check antenna positioning to ensure specified azimuths or mechanical tilts and adjust as necessary.
- Calibrate and align components, using scales, gauges, and other measuring instruments.
- Insert plugs into receptacles and bolt or screw leads to terminals to connect equipment to power sources, using hand tools.
- Install, adjust, and repair stationary and mobile radio transmitting and receiving equipment and two-way radio communication systems.
- Monitor radio range stations to detect transmission flaws and adjust controls to eliminate flaws.
- Tighten loose bolts, using wrenches, and test circuits and connections by opening and closing gates.
- Maintain high tension lines, de-energizing lines for power companies when repairs are requested.
- Inspect and test operation, mechanical parts, and circuitry of gate crossings, signals, and signal equipment such as interlocks and hotbox detectors.
- Inspect electrical units of railroad grade crossing gates and repair loose bolts and defective electrical connections and parts.
- Test and repair track circuits.
- Drive motor vehicles to job sites.
- Install, inspect, maintain, and repair various railroad service equipment on the road or in the shop, including railroad signal systems.
- Inspect switch-controlling mechanisms on trolley wires and in track beds, using hand tools and test equipment.
- Replace defective wiring, broken lenses, or burned-out light bulbs.
- Inspect, maintain, and replace batteries as needed.
- Record and report information about mileage or track inspected, repairs performed, and equipment requiring replacement.
- Lubricate moving parts on gate-crossing mechanisms and swinging signals.
- Clean lenses of lamps with cloths and solvents.
- Test air lines and air cylinders on pneumatically operated gates.
- Tighten loose bolts, using wrenches, and test circuits and connections by opening and closing gates.
- Maintain high tension lines, de-energizing lines for power companies when repairs are requested.
- Repair window sash frames, attach weather stripping and channels to frames, and replace window glass, using hand tools.
- Adjust repaired or replaced units as needed to ensure proper operation.
- Record conditions of cars, and repair and maintenance work performed or to be performed.
- Inspect components such as bearings, seals, gaskets, wheels, and coupler assemblies to determine if repairs are needed.
- Repair or replace defective or worn parts such as bearings, pistons, and gears, using hand tools, torque wrenches, power tools, and welding equipment.
- Inspect the interior and exterior of rail cars coming into rail yards to identify defects and to determine the extent of wear and damage.
- Remove locomotives, car mechanical units, or other components, using pneumatic hoists and jacks, pinch bars, hand tools, and cutting torches.
- Test units for operability before and after repairs.
- Repair, fabricate, and install steel or wood fittings, using blueprints, shop sketches, and instruction manuals.
- Perform scheduled maintenance, and clean units and components.
- Examine car roofs for wear and damage, and repair defective sections, using roofing material, cement, nails, and waterproof paint.
- Paint car exteriors, interiors, and fixtures.
- Repair and maintain electrical and electronic controls for propulsion and braking systems.
- Disassemble units such as water pumps, control valves, and compressors so that repairs can be made.
- Measure diameters of axle wheel seats, using micrometers, and mark dimensions on axles so that wheels can be bored to specified dimensions.
- Test electrical systems of cars by operating systems and using testing equipment such as ammeters.
- Replace defective wiring and insulation, and tighten electrical connections, using hand tools.
- Install and repair interior flooring, fixtures, walls, plumbing, steps, and platforms.
- Align car sides for installation of car ends and crossties, using width gauges, turnbuckles, and wrenches.
- Repair car upholstery.
- Repair window sash frames, attach weather stripping and channels to frames, and replace window glass, using hand tools.
- Adjust repaired or replaced units as needed to ensure proper operation.
- Insert shims, adjust tension on nuts and bolts, or position parts, using hand tools and measuring instruments, to set specified clearances between moving and stationary parts.
- Replace defective parts of machine, or adjust clearances and alignment of moving parts.
- Level bedplate and establish centerline, using straightedge, levels, and transit.
- Align machines or equipment, using hoists, jacks, hand tools, squares, rules, micrometers, lasers, or plumb bobs.
- Assemble and install equipment, using hand tools and power tools.
- Signal crane operator to lower basic assembly units to bedplate, and align unit to centerline.
- Conduct preventative maintenance and repair, and lubricate machines and equipment.
- Attach moving parts and subassemblies to basic assembly unit, using hand tools and power tools.
- Assemble machines, and bolt, weld, rivet, or otherwise fasten them to foundation or other structures, using hand tools and power tools.
- Lay out mounting holes, using measuring instruments, and drill holes with power drill.
- Position steel beams to support bedplates of machines and equipment, using blueprints and schematic drawings to determine work procedures.
- Shrink-fit bushings, sleeves, rings, liners, gears, and wheels to specified items, using portable gas heating equipment.
- Move machinery and equipment, using hoists, dollies, rollers, and trucks.
- Dismantle machinery and equipment for shipment to installation site, performing installation and maintenance work as part of team.
- Weld, repair, and fabricate equipment or machinery.
- Dismantle machines, using hammers, wrenches, crowbars, and other hand tools.
- Fabricate and dismantle parts, equipment, and machines, using a cutting torch or other cutting equipment.
- Bolt parts, such as side and deck plates, jaw plates, and journals, to basic assembly unit.
- Construct foundation for machines, using hand tools and building materials such as wood, cement, and steel.
- Install robot and modify its program, using teach pendant.
- Troubleshoot equipment, electrical components, hydraulics, or other mechanical systems.
- Connect power unit to machines or steam piping to equipment, and test unit to evaluate its mechanical operation.
- Operate engine lathe to grind, file, and turn machine parts to dimensional specifications.
- Insert shims, adjust tension on nuts and bolts, or position parts, using hand tools and measuring instruments, to set specified clearances between moving and stationary parts.
- Replace defective parts of machine, or adjust clearances and alignment of moving parts.
- Clamp seals around valves to secure tanks.
- Start pumps and open valves or use automated equipment to regulate the flow of oil in pipelines and into and out of tanks.
- Signal other workers by telephone or radio to operate pumps, open and close valves, and check temperatures.
- Maintain and repair equipment, or report malfunctioning equipment to supervisors so that repairs can be scheduled.
- Monitor process indicators, instruments, gauges, and meters to detect and report any possible problems.
- Operate control panels to coordinate and regulate process variables such as temperature and pressure, and to direct product flow rate, according to process schedules.
- Verify that incoming and outgoing products are moving through the correct meters, and that meters are working properly.
- Patrol units to monitor the amount of oil in storage tanks, and to verify that activities and operations are safe, efficient, and in compliance with regulations.
- Plan movement of products through lines to processing, storage, and shipping units, using knowledge of system interconnections and capacities.
- Control or operate manifold and pumping systems to circulate liquids through a petroleum refinery.
- Operate auxiliary equipment and control multiple processing units during distilling or treating operations, moving controls that regulate valves, pumps, compressors, and auxiliary equipment.
- Collect product samples by turning bleeder valves, or by lowering containers into tanks to obtain oil samples.
- Read automatic gauges at specified intervals to determine the flow rate of oil into or from tanks, and the amount of oil in tanks.
- Synchronize activities with other pumphouses to ensure a continuous flow of products and a minimum of contamination between products.
- Record and compile operating data, instrument readings, documentation, and results of laboratory analyses.
- Conduct general housekeeping of units, including wiping up oil spills and performing general cleaning duties.
- Inspect pipelines, tightening connections and lubricating valves as necessary.
- Read and analyze specifications, schedules, logs, test results, and laboratory recommendations to determine how to set equipment controls to produce the required qualities and quantities of products.
- Perform tests to check the qualities and grades of products, such as assessing levels of bottom sediment, water, and foreign materials in oil samples, using centrifugal testers.
- Calculate test result values, using standard formulas.
- Clean interiors of processing units by circulating chemicals and solvents within units.
- Coordinate shutdowns and major projects.
- Prepare calculations for receipts and deliveries of oil and oil products.
- Lower thermometers into tanks to obtain temperature readings.
- Clamp seals around valves to secure tanks.
- Start pumps and open valves or use automated equipment to regulate the flow of oil in pipelines and into and out of tanks.
- Position and fasten edges of tarpaulins over building, and tape vents to ensure air-tight environment and to check for leaks.
- Record work activities performed.
- Inspect premises to identify infestation source and extent of damage to property, wall, or roof porosity and access to infested locations.
- Recommend treatment and prevention methods for pest problems to clients.
- Spray or dust chemical solutions, powders, or gases into rooms, onto clothing, furnishings, or wood, or over marshlands, ditches, or catch basins.
- Clean work site after completion of job.
- Drive truck equipped with power spraying equipment.
- Measure area dimensions requiring treatment, calculate fumigant requirements, and estimate cost for service.
- Study preliminary reports or diagrams of infested area and determine treatment type required to eliminate and prevent recurrence of infestation.
- Direct, or assist other workers in, treatment or extermination processes to eliminate or control rodents, insects, or weeds.
- Post warning signs and lock building doors to secure area to be fumigated.
- Set mechanical traps, or place poisonous paste or bait in sewers, burrows, or ditches.
- Cut or bore openings in building or surrounding concrete, access infested areas, insert nozzle, and inject pesticide to impregnate ground.
- Clean and remove blockages from infested areas to facilitate spraying procedures and provide drainage, using brooms, mops, shovels, or rakes.
- Dig up and burn weeds, or spray them with herbicides.
- Position and fasten edges of tarpaulins over building, and tape vents to ensure air-tight environment and to check for leaks.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Explain proper operation of vehicle systems to customers.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, or hand tools.
- Repair plumbing or propane gas lines, using caulking compounds and plastic or copper pipe.
- Confer with customers, read work orders, or examine vehicles needing repair to determine the nature and extent of damage.
- Examine or test operation of parts or systems to ensure completeness of repairs.
- Connect electrical systems to outside power sources, and activate switches to test the operation of appliances or light fixtures.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of toilets or sinks.
- Inspect recreational vehicles to diagnose problems and perform necessary adjustment, repair, or overhaul.
- Inspect, repair, or replace brake systems.
- Diagnose and repair furnace or air conditioning systems.
- Repair leaks with caulking compound or replace pipes, using pipe wrenches.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, or diagrams.
- Remove damaged exterior panels, and repair and replace structural frame members.
- Open and close doors, windows, or drawers to test their operation, trimming edges to fit, as necessary.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Refinish wood surfaces on cabinets, doors, moldings, or floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
