- Cut designs in molds or other materials to be used as models in the fabrication of metal and jewelry products.
Occupations with related tasks Save Table: XLSX CSV
- Shape, trim, or touch up roughed-out designs with appropriate tools to finish carvings.
- Drill holes and cut or carve moldings and grooves in stone, according to diagrams and patterns.
- Guide nozzles over stone, following stencil outlines, or chip along marks to create designs or to work surfaces down to specified finishes.
- Carve designs or figures in full or bas relief on stone, employing knowledge of stone carving techniques and sense of artistry to produce carvings consistent with designers' plans.
- Carve rough designs freehand or by chipping along marks on stone, using mallets and chisels or pneumatic tools.
- Verify depths and dimensions of cuts or carvings to ensure adherence to specifications, blueprints, or models, using measuring instruments.
- Move fingers over surfaces of carvings to ensure smoothness of finish.
- Lay out designs or dimensions from sketches or blueprints on stone surfaces, freehand or by transferring them from tracing paper, using scribes or chalk and measuring instruments.
- Remove or add stencils during blasting to create differing cut depths, intricate designs, or rough, pitted finishes.
- Select chisels, pneumatic or surfacing tools, or sandblasting nozzles, and determine sequence of use.
- Load sandblasting equipment with abrasives, attach nozzles to hoses, and turn valves to admit compressed air and activate jets.
- Cut, shape, and finish rough blocks of building or monumental stone, according to diagrams or patterns.
- Study artistic objects or graphic materials, such as models, sketches, or blueprints, to plan carving or cutting techniques.
- Smooth surfaces of carvings, using rubbing stones.
- Shape, trim, or touch up roughed-out designs with appropriate tools to finish carvings.
- Drill holes and cut or carve moldings and grooves in stone, according to diagrams and patterns.
- Guide nozzles over stone, following stencil outlines, or chip along marks to create designs or to work surfaces down to specified finishes.
- Carve designs or figures in full or bas relief on stone, employing knowledge of stone carving techniques and sense of artistry to produce carvings consistent with designers' plans.
- Carve rough designs freehand or by chipping along marks on stone, using mallets and chisels or pneumatic tools.
- Engrave and print patterns, designs, etchings, trademarks, or lettering onto flat or curved surfaces of a wide variety of metal, glass, plastic, or paper items, using hand tools or hand-held power tools.
- Guide stylus over template, causing cutting tool to duplicate design or letters on workpiece.
- Sandblast exposed areas of glass to cut designs in surfaces, using spray guns.
- Inspect etched work for depth of etching, uniformity, and defects, using calibrated microscopes, gauges, fingers, or magnifying lenses.
- Examine sketches, diagrams, samples, blueprints, or photographs to decide how designs are to be etched, cut, or engraved onto workpieces.
- Clean and polish engraved areas.
- Prepare workpieces for etching or engraving by cutting, sanding, cleaning, polishing, or treating them with wax, acid resist, lime, etching powder, or light-sensitive enamel.
- Prepare etching chemicals according to formulas, diluting acid with water to obtain solutions of specified concentration.
- Use computer software to design patterns for engraving.
- Expose workpieces to acid to develop etch patterns such as designs, lettering, or figures.
- Adjust depths and sizes of cuts by adjusting heights of worktables, or by adjusting machine-arm gauges.
- Measure and compute dimensions of lettering, designs, or patterns to be engraved.
- Neutralize workpieces to remove acid, wax, or enamel, using water, solvents, brushes, or specialized machines.
- Examine engraving for quality of cut, burrs, rough spots, and irregular or incomplete engraving.
- Transfer image to workpiece, using contact printer, pantograph stylus, silkscreen printing device, or stamp pad.
- Set reduction scales to attain specified sizes of reproduction on workpieces, and set pantograph controls for required heights, depths, and widths of cuts.
- Print proofs or examine designs to verify accuracy of engraving, and rework engraving as required.
- Position and clamp workpieces, plates, or rollers in holding fixtures.
- Remove wax or tape from etched glassware by using a stylus or knife, or by immersing ware in hot water.
- Start machines and lower cutting tools to beginning points on patterns.
- Determine machine settings, and move bars or levers to reproduce designs on rollers or plates.
- Remove completed workpieces and place them in trays.
- Insert cutting tools or bits into machines and secure them with wrenches.
- Sketch, trace, or scribe layout lines and designs on workpieces, plates, dies, or rollers, using compasses, scribers, gravers, or pencils.
- Fill etched characters with opaque paste to improve readability.
- Brush or wipe acid over engraving to darken or highlight inscriptions.
- Engrave and print patterns, designs, etchings, trademarks, or lettering onto flat or curved surfaces of a wide variety of metal, glass, plastic, or paper items, using hand tools or hand-held power tools.
- Guide stylus over template, causing cutting tool to duplicate design or letters on workpiece.
- Sandblast exposed areas of glass to cut designs in surfaces, using spray guns.
- Stencil identifying information on ingots and pigs, using special hand tools.
- Pour and regulate the flow of molten metal into molds and forms to produce ingots or other castings, using ladles or hand-controlled mechanisms.
- Read temperature gauges and observe color changes, adjusting furnace flames, torches, or electrical heating units as necessary to melt metal to specifications.
- Remove solidified steel or slag from pouring nozzles, using long bars or oxygen burners.
- Examine molds to ensure they are clean, smooth, and properly coated.
- Collect samples, or signal workers to sample metal for analysis.
- Load specified amounts of metal and flux into furnaces or clay crucibles.
- Position equipment such as ladles, grinding wheels, pouring nozzles, or crucibles, or signal other workers to position equipment.
- Skim slag or remove excess metal from ingots or equipment, using hand tools, strainers, rakes, or burners, collecting scrap for recycling.
- Transport metal ingots to storage areas, using forklifts.
- Assemble and embed cores in casting frames, using hand tools and equipment.
- Turn valves to circulate water through cores, or spray water on filled molds to cool and solidify metal.
- Pull levers to lift ladle stoppers and to allow molten steel to flow into ingot molds to specified heights.
- Remove metal ingots or cores from molds, using hand tools, cranes, and chain hoists.
- Repair and maintain metal forms and equipment, using hand tools, sledges, and bars.
- Add metal to molds to compensate for shrinkage.
- Stencil identifying information on ingots and pigs, using special hand tools.
- Stamp, etch, or scribe identifying information on finished component according to specifications.
- Inspect materials, components, or products for surface defects and measure circuitry, using electronic test equipment, precision measuring instruments, microscope, and standard procedures.
- Study work orders, instructions, formulas, and processing charts to determine specifications and sequence of operations.
- Clean semiconductor wafers using cleaning equipment, such as chemical baths, automatic wafer cleaners, or blow-off wands.
- Maintain processing, production, and inspection information and reports.
- Place semiconductor wafers in processing containers or equipment holders, using vacuum wand or tweezers.
- Load and unload equipment chambers and transport finished product to storage or to area for further processing.
- Manipulate valves, switches, and buttons, or key commands into control panels to start semiconductor processing cycles.
- Inspect equipment for leaks, diagnose malfunctions, and request repairs.
- Clean and maintain equipment, including replacing etching and rinsing solutions and cleaning bath containers and work area.
- Monitor operation and adjust controls of processing machines and equipment to produce compositions with specific electronic properties, using computer terminals.
- Load semiconductor material into furnace.
- Count, sort, and weigh processed items.
- Scribe or separate wafers into dice.
- Calculate etching time based on thickness of material to be removed from wafers or crystals.
- Etch, lap, polish, or grind wafers or ingots to form circuitry and change conductive properties, using etching, lapping, polishing, or grinding equipment.
- Align photo mask pattern on photoresist layer, expose pattern to ultraviolet light, and develop pattern, using specialized equipment.
- Stamp, etch, or scribe identifying information on finished component according to specifications.
- Engrave or stamp identifying symbols, letters, or numbers on products.
- Read work orders or examine parts to determine parts or sections of products to be produced.
- Trim or remove excess material, using scrapers, knives, or band saws.
- Brush or spray mold surfaces with parting agents or insert paper into molds to ensure smoothness and prevent sticking or seepage.
- Assemble, insert, and adjust wires, tubes, cores, fittings, rods, or patterns into molds, using hand tools and depth gauges.
- Clean, finish, and lubricate molds and mold parts.
- Separate models or patterns from molds and examine products for accuracy.
- Set the proper operating temperature for each casting.
- Load or stack filled molds in ovens, dryers, or curing boxes, or on storage racks or carts.
- Align and assemble parts to produce completed products, using gauges and hand tools.
- Operate and adjust controls of heating equipment to melt material or to cure, dry, or bake filled molds.
- Select sizes and types of molds according to instructions.
- Patch broken edges or fractures, using clay or plaster.
- Withdraw cores or other loose mold members after castings solidify.
- Repair mold defects, such as cracks or broken edges, using patterns, mold boxes, or hand tools.
- Measure and cut products to specified dimensions, using measuring and cutting instruments.
- Smooth surfaces of molds, using scraping tools or sandpaper.
- Measure ingredients and mix molding, casting material, or sealing compounds to prescribed consistencies, according to formulas.
- Remove excess materials and level and smooth wet mold mixtures.
- Verify dimensions of products, using measuring instruments, such as calipers, vernier gauges, or protractors.
- Bore holes or cut grates, risers, or pouring spouts in molds, using power tools.
- Tap or tilt molds to ensure uniform distribution of materials.
- Construct or form molds for use in casting clay or plaster objects, using plaster, fiberglass, rubber, casting machines, patterns, or flasks.
- Pour, pack, spread, or press plaster, concrete, or other materials into or around models or molds.
- Engrave or stamp identifying symbols, letters, or numbers on products.
- Perform highly skilled hand finishing binding operations, such as grooving or lettering.
- Examine stitched, collated, bound, or unbound product samples for defects, such as imperfect bindings, ink spots, torn pages, loose pages, or loose or uncut threads.
- Read work orders to determine instructions and specifications for machine set-up.
- Install or adjust bindery machine devices, such as knives, guides, rollers, rounding forms, creasing rams, or clamps, to accommodate sheets, signatures, or books of specified sizes.
- Trim edges of books to size, using cutting machines, book trimming machines, or hand cutters.
- Stitch or glue endpapers, bindings, backings, or signatures, using sewing machines, glue machines, or glue and brushes.
- Monitor machine operations to detect malfunctions or to determine whether adjustments are needed.
- Maintain records, such as daily production records, using specified forms.
- Lubricate, clean, or make minor repairs to machine parts to keep machines in working condition.
- Set up or operate bindery machines, such as coil binders, thermal or tape binders, plastic comb binders, or specialty binders.
- Set up or operate machines that perform binding operations, such as pressing, folding, or trimming.
- Prepare finished books for shipping by wrapping or packing books and stacking boxes on pallets.
- Set up or operate glue machines by filling glue reservoirs, turning switches to activate heating elements, or adjusting glue flow or conveyor speed.
- Train workers to set up, operate, and use automatic bindery machines.
- Insert book bodies in devices that form back edges of books into convex shapes and produce grooves that facilitate cover attachment.
- Cut cover material to specified dimensions, fitting and gluing material to binder boards by hand or machine.
- Cut binder boards to specified dimensions, using board shears, hand cutters, or cutting machines.
- Bind new books, using hand tools such as bone folders, knives, hammers, or brass binding tools.
- Imprint or emboss lettering, designs, or numbers on book covers, using gold, silver, or colored foil, and stamping machines.
- Compress sewed or glued signatures, using hand presses or smashing machines.
- Meet with clients, printers, or designers to discuss job requirements or binding plans.
- Form book bodies by folding and sewing printed sheets to form signatures and assembling signatures in numerical order.
- Design original or special bindings for limited editions or other custom binding projects.
- Punch holes in and fasten paper sheets, signatures, or other material, using hand or machine punches and staplers.
- Repair, restore, or rebind old, rare, or damaged books, using hand tools.
- Perform highly skilled hand finishing binding operations, such as grooving or lettering.
