- Smooth surfaces of finished pieces, using rubber scrapers and wet sponges.
Occupations with related tasks Save Table: XLSX CSV
- File, grind, sand, and smooth filled or repaired surfaces, using power tools and hand tools.
- Fit and weld replacement parts into place, using wrenches and welding equipment, and grind down welds to smooth them, using power grinders and other tools.
- Sand body areas to be painted and cover bumpers, windows, and trim with masking tape or paper to protect them from the paint.
- Position dolly blocks against surfaces of dented areas and beat opposite surfaces to remove dents, using hammers.
- Fill small dents that cannot be worked out with plastic or solder.
- Remove small pits and dimples in body metal, using pick hammers and punches.
- Inspect repaired vehicles for proper functioning, completion of work, dimensional accuracy, and overall appearance of paint job, and test-drive vehicles to ensure proper alignment and handling.
- Prime and paint repaired surfaces, using paint sprayguns and motorized sanders.
- Follow supervisors' instructions as to which parts to restore or replace and how much time the job should take.
- Chain or clamp frames and sections to alignment machines that use hydraulic pressure to align damaged components.
- Cut and tape plastic separating film to outside repair areas to avoid damaging surrounding surfaces during repair procedure and remove tape and wash surfaces after repairs are complete.
- Review damage reports, prepare or review repair cost estimates, and plan work to be performed.
- Remove damaged sections of vehicles using metal-cutting guns, air grinders and wrenches, and install replacement parts using wrenches or welding equipment.
- Remove upholstery, accessories, electrical window-and-seat-operating equipment, and trim to gain access to vehicle bodies and fenders.
- Mix polyester resins and hardeners to be used in restoring damaged areas.
- Fit and secure windows, vinyl roofs, and metal trim to vehicle bodies, using caulking guns, adhesive brushes, and mallets.
- Adjust or align headlights, wheels, and brake systems.
- Replace damaged glass on vehicles.
- Remove damaged panels, and identify the family and properties of the plastic used on a vehicle.
- Apply heat to plastic panels, using hot-air welding guns or immersion in hot water, and press the softened panels back into shape by hand.
- Clean work areas, using air hoses, to remove damaged material and discarded fiberglass strips used in repair procedures.
- Soak fiberglass matting in resin mixtures and apply layers of matting over repair areas to specified thicknesses.
- Read specifications or confer with customers to determine the desired custom modifications for altering the appearance of vehicles.
- Cut openings in vehicle bodies for the installation of customized windows, using templates and power shears or chisels.
- Measure and mark vinyl material and cut material to size for roof installation, using rules, straightedges, and hand shears.
- File, grind, sand, and smooth filled or repaired surfaces, using power tools and hand tools.
- Fit and weld replacement parts into place, using wrenches and welding equipment, and grind down welds to smooth them, using power grinders and other tools.
- Sand body areas to be painted and cover bumpers, windows, and trim with masking tape or paper to protect them from the paint.
- Position dolly blocks against surfaces of dented areas and beat opposite surfaces to remove dents, using hammers.
- Fill small dents that cannot be worked out with plastic or solder.
- Remove small pits and dimples in body metal, using pick hammers and punches.
- Polish instruments, using rags and polishing compounds, buffing wheels, or burnishing tools.
- Remove irregularities from tuning pins, strings, and hammers of pianos, using wood blocks or filing tools.
- Remove dents and burrs from metal instruments, using mallets and burnishing tools.
- Play instruments to evaluate their sound quality and to locate any defects.
- Adjust string tensions to tune instruments, using hand tools and electronic tuning devices.
- Reassemble instruments following repair, using hand tools and power tools and glue, hair, yarn, resin, or clamps, and lubricate instruments as necessary.
- Disassemble instruments and parts for repair and adjustment.
- Repair or replace musical instrument parts and components, such as strings, bridges, felts, and keys, using hand and power tools.
- Inspect instruments to locate defects, and to determine their value or the level of restoration required.
- Compare instrument pitches with tuning tool pitches to tune instruments.
- String instruments, and adjust trusses and bridges of instruments to obtain specified string tensions and heights.
- Repair cracks in wood or metal instruments, using pinning wire, lathes, fillers, clamps, or soldering irons.
- Mix and measure glue that will be used for instrument repair.
- Shape old parts and replacement parts to improve tone or intonation, using hand tools, lathes, or soldering irons.
- Refinish instruments to protect and decorate them, using hand tools, buffing tools, and varnish.
- Make wood replacement parts, using woodworking machines and hand tools.
- Align pads and keys on reed or wind instruments.
- Solder posts and parts to hold them in their proper places.
- Test tubes and pickups in electronic amplifier units, and solder parts and connections as necessary.
- Adjust felt hammers on pianos to increase tonal mellowness or brilliance, using sanding paddles, lacquer, or needles.
- Strike wood, fiberglass, or metal bars of instruments, and use tuned blocks, stroboscopes, or electronic tuners to evaluate tones made by instruments.
- Wash metal instruments in lacquer-stripping and cyanide solutions to remove lacquer and tarnish.
- Deliver pianos to purchasers or to locations of their use.
- Remove drumheads by removing tension rods with drum keys and cutting tools.
- Solder or weld frames of mallet instruments and metal drum parts.
- Repair breaks in percussion instruments, such as drums and cymbals, using drill presses, power saws, glue, clamps, grinding wheels, or other hand tools.
- Assemble bars onto percussion instruments.
- Clean, sand, and paint parts of percussion instruments to maintain their condition.
- Replace xylophone bars and wheels.
- Polish instruments, using rags and polishing compounds, buffing wheels, or burnishing tools.
- Remove irregularities from tuning pins, strings, and hammers of pianos, using wood blocks or filing tools.
- Remove dents and burrs from metal instruments, using mallets and burnishing tools.
- Buff defective areas of inner tubes, using scrapers.
- Prepare rims and wheel drums for reassembly by scraping, grinding, or sandblasting.
- Raise vehicles, using hydraulic jacks.
- Remount wheels onto vehicles.
- Unbolt and remove wheels from vehicles, using lug wrenches or other hand or power tools.
- Place wheels on balancing machines to determine counterweights required to balance wheels.
- Identify tire size and ply and inflate tires accordingly.
- Replace valve stems and remove puncturing objects.
- Hammer required counterweights onto rims of wheels.
- Reassemble tires onto wheels.
- Seal punctures in tubeless tires by inserting adhesive material and expanding rubber plugs into punctures, using hand tools.
- Inspect tire casings for defects, such as holes or tears.
- Locate punctures in tubeless tires by visual inspection or by immersing inflated tires in water baths and observing air bubbles.
- Glue tire patches over ruptures in tire casings, using rubber cement.
- Assist mechanics and perform various mechanical duties, such as changing oil or checking and replacing batteries.
- Rotate tires to different positions on vehicles, using hand tools.
- Clean and tidy up the shop.
- Order replacements for tires or tubes.
- Separate tubed tires from wheels, using rubber mallets and metal bars or mechanical tire changers.
- Inflate inner tubes and immerse them in water to locate leaks.
- Clean sides of whitewall tires.
- Apply rubber cement to buffed tire casings prior to vulcanization process.
- Patch tubes with adhesive rubber patches or seal rubber patches to tubes, using hot vulcanizing plates.
- Drive automobile or service trucks to industrial sites to provide services or respond to emergency calls.
- Buff defective areas of inner tubes, using scrapers.
- Prepare rims and wheel drums for reassembly by scraping, grinding, or sandblasting.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Hammer out dents and twists in tools and equipment.
- Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Lift units or parts such as motors or generators, using cranes or chain hoists, or signal crane operators to lift heavy parts or subassemblies.
- Record repairs required, parts used, and labor time.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Lubricate moving parts.
- Read service guides to find information needed to perform repairs.
- Inspect electrical connections, wiring, relays, charging resistance boxes, and storage batteries, following wiring diagrams.
- Scrape and clean units or parts, using cleaning solvents and equipment such as buffing wheels.
- Weld, braze, or solder electrical connections.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Steam-clean polishing and buffing wheels to remove abrasives and bonding materials, and spray, brush, or recoat surfaces as necessary.
- Set machinery for proper performance, using computers.
- Test equipment for overheating, using speed gauges and thermometers.
- Maintain stocks of parts.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Solder, wrap, and coat wires to ensure proper insulation.
- Rewire electrical systems, and repair or replace electrical accessories.
- Clean cells, cell assemblies, glassware, leads, electrical connections, and battery poles, using scrapers, steam, water, emery cloths, power grinders, or acid.
- Rewind coils on cores in slots, or make replacement coils, using coil-winding machines.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Repair and operate battery-charging equipment.
- Sharpen tools such as saws, picks, shovels, screwdrivers, and scoops, either manually or by using bench grinders and emery wheels.
- Test battery charges, and replace or recharge batteries as necessary.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Hammer out dents and twists in tools and equipment.
- Smooth seams with heated irons, flat bones, or rubbing sticks.
- Select thread, twine, cord, or yarn to be used, and thread needles.
- Measure and align parts, fasteners, or trimmings, following seams, edges, or markings on parts.
- Trim excess threads or edges of parts, using scissors or knives.
- Sew, join, reinforce, or finish parts of articles, such as garments, books, mattresses, toys, and wigs, using needles and thread or other materials.
- Use different sewing techniques such as felling, tacking, basting, embroidery, and fagoting.
- Fit garments on clients, altering as needed.
- Draw and cut patterns according to specifications.
- Fold, twist, stretch, or drape material, and secure articles in preparation for sewing.
- Sew buttonholes, or add lace or other trimming.
- Tie, knit, weave or knot ribbon, yarn, or decorative materials.
- Smooth seams with heated irons, flat bones, or rubbing sticks.
- Release air bubbles and smooth seams, using rollers.
- Spray chopped fiberglass, resins, and catalysts onto prepared molds or dies using pneumatic spray guns with chopper attachments.
- Mix catalysts into resins, and saturate cloth and mats with mixtures, using brushes.
- Check completed products for conformance to specifications and for defects by measuring with rulers or micrometers, by checking them visually, or by tapping them to detect bubbles or dead spots.
- Pat or press layers of saturated mat or cloth into place on molds, using brushes or hands, and smooth out wrinkles and air bubbles with hands or squeegees.
- Select precut fiberglass mats, cloth, and wood-bracing materials as required by projects being assembled.
- Bond wood reinforcing strips to decks and cabin structures of watercraft, using resin-saturated fiberglass.
- Trim excess materials from molds, using hand shears or trimming knives.
- Apply layers of plastic resin to mold surfaces prior to placement of fiberglass mats, repeating layers until products have the desired thicknesses and plastics have jelled.
- Inspect, clean, and assemble molds before beginning work.
- Cure materials by letting them set at room temperature, placing them under heat lamps, or baking them in ovens.
- Apply lacquers and waxes to mold surfaces to facilitate assembly and removal of laminated parts.
- Repair or modify damaged or defective glass-fiber parts, checking thicknesses, densities, and contours to ensure a close fit after repair.
- Check all dies, templates, and cutout patterns to be used in the manufacturing process to ensure that they conform to dimensional data, photographs, blueprints, samples, or customer specifications.
- Trim cured materials by sawing them with diamond-impregnated cutoff wheels.
- Mask off mold areas not to be laminated, using cellophane, wax paper, masking tape, or special sprays containing mold-release substances.
- Release air bubbles and smooth seams, using rollers.