- Install pipe assemblies, fittings, valves, appliances such as dishwashers or water heaters, or fixtures such as sinks or toilets, using hand or power tools.
Occupations with related tasks Save Table: XLSX CSV
- Install copper or plastic plumbing using pipes, fittings, pipe cutters, acetylene torches, solder, wire brushes, sand cloths, flux, plastic pipe cleaners, or plastic glue.
- Install circulating pumps using pipe, fittings, soldering equipment, electrical supplies, and hand tools.
- Connect water heaters and storage tanks to power and water sources.
- Install plumbing, such as dip tubes, port fittings, drain tank valves, pressure temperature relief valves, or tanks, according to manufacturer specifications and building codes.
- Test operation or functionality of mechanical, plumbing, electrical, and control systems.
- Apply weather seal, such as pipe flashings and sealants, to roof penetrations and structural devices.
- Install solar collector mounting devices on tile, asphalt, shingle, or built-up gravel roofs, using appropriate materials and penetration methods.
- Identify plumbing, electrical, environmental, or safety hazards associated with solar thermal installations.
- Demonstrate start-up, shut-down, maintenance, diagnostic, and safety procedures to thermal system owners.
- Install flat-plat, evacuated glass, or concentrating solar collectors on mounting devices, using brackets or struts.
- Install solar thermal system controllers and sensors.
- Fill water tanks and check tanks, pipes, and fittings for leaks.
- Design active direct or indirect, passive direct or indirect, or pool solar systems.
- Determine locations for installing solar subsystem components, including piping, water heaters, valves, and ancillary equipment.
- Perform routine maintenance or repairs to restore solar thermal systems to baseline operating conditions.
- Install heat exchangers and heat exchanger fluids according to installation manuals and schematics.
- Apply operation or identification tags or labels to system components, as required.
- Cut, miter, and glue piping insulation to insulate plumbing pipes and fittings.
- Install monitoring system components, such as flow meters, temperature gauges, and pressure gauges, according to system design and manufacturer specifications.
- Assess collector sites to ensure structural integrity of potential mounting surfaces or the best orientation and tilt for solar collectors.
- Apply ultraviolet radiation protection to prevent degradation of plumbing.
- Install copper or plastic plumbing using pipes, fittings, pipe cutters, acetylene torches, solder, wire brushes, sand cloths, flux, plastic pipe cleaners, or plastic glue.
- Install circulating pumps using pipe, fittings, soldering equipment, electrical supplies, and hand tools.
- Connect water heaters and storage tanks to power and water sources.
- Install plumbing, such as dip tubes, port fittings, drain tank valves, pressure temperature relief valves, or tanks, according to manufacturer specifications and building codes.
- Measure, cut, thread and assemble new pipe, placing the assembled pipe in hangers or other supports.
- Mount brackets and hangers on walls and ceilings to hold pipes, and set sleeves or inserts to provide support for pipes.
- Excavate and grade ditches, and lay and join pipe for water and sewer service.
- Cut or drill holes in walls or floors to accommodate the passage of pipes.
- Perform rough-ins, repair and replace fixtures and water heaters, and locate, repair, or remove leaking or broken pipes.
- Assist pipe fitters in the layout, assembly, and installation of piping for air, ammonia, gas, and water systems.
- Cut pipe and lift up to fitters.
- Fit or assist in fitting valves, couplings, or assemblies to tanks, pumps, or systems, using hand tools.
- Requisition tools and equipment, select type and size of pipe, and collect and transport materials and equipment to work site.
- Disassemble and remove damaged or worn pipe.
- Clean shop, work area, and machines, using solvent and rags.
- Install gas burners to convert furnaces from wood, coal, or oil.
- Fill pipes with sand or resin to prevent distortion, and hold pipes during bending and installation.
- Immerse pipe in chemical solution to remove dirt, oil, and scale.
- Clean and renew steam traps.
- Measure, cut, thread and assemble new pipe, placing the assembled pipe in hangers or other supports.
- Mount brackets and hangers on walls and ceilings to hold pipes, and set sleeves or inserts to provide support for pipes.
- Excavate and grade ditches, and lay and join pipe for water and sewer service.
- Install or repair sanitary or stormwater sewer structures or pipe systems.
- Align and position pipes to prepare them for welding or sealing.
- Install or use instruments such as lasers, grade rods, or transit levels.
- Cut pipes to required lengths.
- Connect pipe pieces and seal joints, using welding equipment, cement, or glue.
- Cover pipes with earth or other materials.
- Check slopes for conformance to requirements, using levels or lasers.
- Lay out pipe routes, following written instructions or blueprints and coordinating layouts with supervisors.
- Operate mechanized equipment, such as pickup trucks, rollers, tandem dump trucks, front-end loaders, or backhoes.
- Grade or level trench bases, using tamping machines or hand tools.
- Dig trenches to desired or required depths, by hand or using trenching tools.
- Tap and drill holes into pipes to introduce auxiliary lines or devices.
- Locate existing pipes needing repair or replacement, using magnetic or radio indicators.
- Train or supervise others in laying pipe.
- Install or repair sanitary or stormwater sewer structures or pipe systems.
- Align and position pipes to prepare them for welding or sealing.
- Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.
- Lay gas and oil pipelines.
- Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.
- Guide cranes to move loads about decks.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Bolt together pump and engine parts.
- Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.
- Clean trucks used in the fields.
- Bolt or nail together wood or steel framework to erect derricks.
- Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.
- Supply equipment to rig floors as requested and provide assistance to roughnecks.
- Clean up spilled oil by bailing it into barrels.
- Keep pipe deck and main deck areas clean and tidy.
- Dig drainage ditches around wells and storage tanks.
- Cut down and remove trees and brush to clear drill sites, to reduce fire hazards, and to make way for roads to sites.
- Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.
- Lay gas and oil pipelines.
- Position, join, align, or seal structural components, such as concrete wall sections or pipes.
- Install sewer, water, or storm drain pipes, using pipe-laying machinery or laser guidance equipment.
- Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.
- Lubricate, clean, or repair machinery, equipment, or tools.
- Signal equipment operators to facilitate alignment, movement, or adjustment of machinery, equipment, or materials.
- Read plans, instructions, or specifications to determine work activities.
- Measure, mark, or record openings or distances to layout areas where construction work will be performed.
- Clean or prepare construction sites to eliminate possible hazards.
- Dig ditches or trenches, backfill excavations, or compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, or rakes.
- Load, unload, or identify building materials, machinery, or tools, distributing them to the appropriate locations, according to project plans or specifications.
- Perform site activities required of green certified construction practices, such as implementing waste management procedures, identifying materials for reuse, or installing erosion or sedimentation control mechanisms.
- Control traffic passing near, in, or around work zones.
- Operate or maintain air monitoring or other sampling devices in confined or hazardous environments.
- Smooth or finish freshly poured cement or concrete, using floats, trowels, screeds, or powered cement finishing tools.
- Erect or dismantle scaffolding, shoring, braces, traffic barricades, ramps, or other temporary structures.
- Provide assistance to craft workers, such as carpenters, plasterers, or masons.
- Perform building weatherization tasks, such as repairing windows, adding insulation, or applying weather-stripping materials.
- Apply weather-stripping to reduce energy loss.
- Spray materials, such as water, sand, steam, vinyl, paint, or stucco, through hoses to clean, coat, or seal surfaces.
- Raze buildings or salvage useful materials.
- Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.
- Position or dismantle forms for pouring concrete, using saws, hammers, nails, or bolts.
- Grind, scrape, sand, or polish surfaces, such as concrete, marble, terrazzo, or wood flooring, using abrasive tools or machines.
- Place, consolidate, or protect case-in-place concrete or masonry structures.
- Mix ingredients to create compounds for covering or cleaning surfaces.
- Mix, pour, or spread concrete, using portable cement mixers.
- Operate jackhammers or drills to break up concrete or pavement.
- Apply caulking compounds by hand or caulking guns to protect against entry of water or air.
- Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings or walls.
- Identify, pack, or transport hazardous or radioactive materials.
- Use computers or other input devices to control robotic pipe cutters or cleaners.
- Perform construction laborer duties at green building sites, such as renewable energy plants or wind turbine installations.
- Position, join, align, or seal structural components, such as concrete wall sections or pipes.
- Install sewer, water, or storm drain pipes, using pipe-laying machinery or laser guidance equipment.
- Install pressure-control devices onto wellheads.
- Maintain and perform safety inspections on equipment and tools.
- Operate controls that raise derricks or level rigs.
- Listen to engines, rotary chains, or other equipment to detect faulty operations or unusual well conditions.
- Prepare reports of services rendered, tools used, or time required, for billing purposes.
- Confer with others to gather information regarding pipe or tool sizes or borehole conditions in wells.
- Operate pumps that circulate water, oil, or other fluids through wells to remove sand or other materials obstructing the free flow of oil.
- Drive truck-mounted units to well sites.
- Interpret instrument readings to ascertain the depth of obstruction.
- Thread cables through derrick pulleys, using hand tools.
- Select fishing methods or tools for removing obstacles such as liners, broken casing, screens, or drill pipe.
- Close and seal wells no longer in use.
- Direct drilling crews performing activities such as assembling and connecting pipe, applying weights to drill pipes, or drilling around lodged obstacles.
- Apply green technologies or techniques, such as the use of coiled tubing, slim-hole drilling, horizontal drilling, hydraulic fracturing, or gas lift systems.
- Operate specialized equipment to remove obstructions by backing off or severing pipes by chemical or explosive action.
- Perforate well casings or sidewalls of boreholes with explosive charges.
- Examine unserviceable wells to determine actions to be taken to improve well conditions.
- Monitor sound wave-generating or detecting mechanisms to determine well fluid levels.
- Insert detection instruments into wells with obstructions.
- Install pressure-control devices onto wellheads.
- Line drilled holes with pipes, and install all necessary hardware, to prepare new wells.
- Train crews, and introduce procedures to make drill work more safe and effective.
- Observe pressure gauge and move throttles and levers to control the speed of rotary tables, and to regulate pressure of tools at bottoms of boreholes.
- Count sections of drill rod to determine depths of boreholes.
- Push levers and brake pedals to control gasoline, diesel, electric, or steam draw works that lower and raise drill pipes and casings in and out of wells.
- Connect sections of drill pipe, using hand tools and powered wrenches and tongs.
- Maintain records of footage drilled, location and nature of strata penetrated, materials and tools used, services rendered, and time required.
- Maintain and adjust machinery to ensure proper performance.
- Start and examine operation of slush pumps to ensure circulation and consistency of drilling fluid or mud in well.
- Locate and recover lost or broken bits, casings, and drill pipes from wells, using special tools.
- Weigh clay, and mix with water and chemicals to make drilling mud.
- Direct rig crews in drilling and other activities, such as setting up rigs and completing or servicing wells.
- Monitor progress of drilling operations, and select and change drill bits according to the nature of strata, using hand tools.
- Repair or replace defective parts of machinery, such as rotary drill rigs, water trucks, air compressors, and pumps, using hand tools.
- Clean and oil pulleys, blocks, and cables.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Remove core samples during drilling to determine the nature of the strata being drilled.
- Cap wells with packers, or turn valves, to regulate outflow of oil from wells.
- Position and prepare truck-mounted derricks at drilling areas specified on field maps.
- Plug observation wells, and restore sites.
- Lower and explode charges in boreholes to start flow of oil from wells.
- Dig holes, set forms, and mix and pour concrete, for foundations of steel or wooden derricks.
- Line drilled holes with pipes, and install all necessary hardware, to prepare new wells.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Maintain equipment, making repairs or modifications when necessary.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Transport prefabricated parts to construction sites for assembly and installation.
- Hire, train, or supervise new employees or apprentices.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Fabricate or alter parts at construction sites, using shears, hammers, punches, or drills.
- Determine project requirements, such as scope, assembly sequences, or required methods or materials, using blueprints, drawings, or written or verbal instructions.
- Maneuver completed roofing units into position for installation.
- Select gauges or types of sheet metal or nonmetallic material, according to product specifications.
- Shape metal material over anvils, blocks, or other forms, using hand tools.
- Trim, file, grind, deburr, buff, or smooth surfaces, seams, or joints of assembled parts, using hand tools or portable power tools.
- Inspect individual parts, assemblies, or installations, using measuring instruments, such as calipers, scales, or micrometers.
- Develop or lay out patterns, using computerized metalworking equipment.
- Convert blueprints into shop drawings to be followed in the construction or assembly of sheet metal products.
- Perform sheet metal work necessary for solar panel installations.
- Verify that heating, ventilating, and air conditioning (HVAC) systems are designed, installed, and calibrated in accordance with green certification standards, such as those of Leadership in Energy and Environmental Design (LEED).
- Secure metal roof panels in place by interlocking and fastening grooved panel edges.
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Finish parts, using hacksaws or hand, rotary, or squaring shears.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
