- Bolt together pump and engine parts.
Occupations with related tasks Save Table: XLSX CSV
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Connect car frames to counterweights, using steel cables.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Disassemble defective units, and repair or replace parts such as locks, gears, cables, and electric wiring.
- Check that safety regulations and building codes are met, and complete service reports verifying conformance to standards.
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Adjust safety controls, counterweights, door mechanisms, and components such as valves, ratchets, seals, and brake linings.
- Read and interpret blueprints to determine the layout of system components, frameworks, and foundations, and to select installation equipment.
- Maintain log books that detail all repairs and checks performed.
- Connect electrical wiring to control panels and electric motors.
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Participate in additional training to keep skills up to date.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
- Install outer doors and door frames at elevator entrances on each floor of a structure.
- Bolt or weld steel rails to the walls of shafts to guide elevators, working from scaffolding or platforms.
- Cut prefabricated sections of framework, rails, and other components to specified dimensions.
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Connect car frames to counterweights, using steel cables.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Insert waterproof sealers, bullets, and/or powder charges into guns, and screw gun ports back into place.
- Examine blast areas to determine amounts and kinds of explosive charges needed and to ensure that safety laws are observed.
- Tie specified lengths of delaying fuses into patterns in order to time sequences of explosions.
- Place safety cones around blast areas to alert other workers of danger zones, and signal workers as necessary to ensure that they clear blast sites prior to explosions.
- Place explosive charges in holes or other spots; then detonate explosives to demolish structures or to loosen, remove, or displace earth, rock, or other materials.
- Insert, pack, and pour explosives, such as dynamite, ammonium nitrate, black powder, or slurries into blast holes; then shovel drill cuttings, admit water into boreholes, and tamp material to compact charges.
- Mark patterns, locations, and depths of charge holes for drilling, and issue drilling instructions.
- Compile and keep gun and explosives records in compliance with local and federal laws.
- Measure depths of drilled blast holes, using weighted tape measures.
- Connect electrical wire to primers, and cover charges or fill blast holes with clay, drill chips, sand, or other material.
- Lay primacord between rows of charged blast holes, and tie cord into main lines to form blast patterns.
- Verify detonation of charges by observing control panels, or by listening for the sounds of blasts.
- Move and store inventories of explosives, loaded perforating guns, and other materials, according to established safety procedures.
- Light fuses, drop detonating devices into wells or boreholes, or activate firing devices with plungers, dials, or buttons, in order to set off single or multiple blasts.
- Drive trucks to transport explosives and blasting equipment to blasting sites.
- Cut specified lengths of primacord and attach primers to cord ends.
- Maintain inventory levels, ordering new supplies as necessary.
- Repair and service blasting, shooting, and automotive equipment, and electrical wiring and instruments, using hand tools.
- Set up and operate short-wave radio or field telephone equipment to transmit and receive blast information.
- Clean, gauge, and lubricate gun ports.
- Lower perforating guns into wells, using hoists; then use measuring devices and instrument panels to position guns in correct positions for taking samples.
- Create and lay out designs for drill and blast patterns.
- Document geological formations encountered during work.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Set up and operate equipment such as hoists, jackhammers, and drills, in order to bore charge holes.
- Signal crane operators to move equipment.
- Operate drones for aerial survey of blast sites and for post-blast damage assessment.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Insert waterproof sealers, bullets, and/or powder charges into guns, and screw gun ports back into place.
- Rotate through all the tasks required in a particular production process.
- Provide assistance in the production of wiring assemblies.
- Perform quality checks on products and parts.
- Review work orders and blueprints to ensure work is performed according to specifications.
- Determine work assignments and procedures.
- Supervise assemblers and train employees on job procedures.
- Shovel, sweep, or otherwise clean work areas.
- Maintain production equipment and machinery.
- Complete production reports to communicate team production level to management.
- Package finished products and prepare them for shipment.
- Operate machinery and heavy equipment, such as forklifts.
- Rotate through all the tasks required in a particular production process.
- Provide assistance in the production of wiring assemblies.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Conduct pressure tests on vessels, such as boilers.
- Study blueprints to determine locations, relationships, or dimensions of parts.
- Examine boilers, pressure vessels, tanks, or vats to locate defects, such as leaks, weak spots, or defective sections, so that they can be repaired.
- Inspect assembled vessels or individual components, such as tubes, fittings, valves, controls, or auxiliary mechanisms, to locate any defects.
- Lay out plate, sheet steel, or other heavy metal and locate and mark bending and cutting lines, using protractors, compasses, and drawing instruments or templates.
- Bell, bead with power hammers, or weld pressure vessel tube ends to ensure leakproof joints.
- Locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments.
- Shape or fabricate parts, such as stacks, uptakes, or chutes, to adapt pressure vessels, heat exchangers, or piping to premises, using heavy-metalworking machines such as brakes, rolls, or drill presses.
- Position, align, and secure structural parts or related assemblies to boiler frames, tanks, or vats of pressure vessels, following blueprints.
- Clean pressure vessel equipment, using scrapers, wire brushes, and cleaning solvents.
- Repair or replace defective pressure vessel parts, such as safety valves or regulators, using torches, jacks, caulking hammers, power saws, threading dies, welding equipment, or metalworking machinery.
- Attach rigging and signal crane or hoist operators to lift heavy frame and plate sections or other parts into place.
- Straighten or reshape bent pressure vessel plates or structure parts, using hammers, jacks, or torches.
- Shape seams, joints, or irregular edges of pressure vessel sections or structural parts to attain specified fit of parts, using cutting torches, hammers, files, or metalworking machines.
- Bolt or arc weld pressure vessel structures and parts together, using wrenches or welding equipment.
- Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Assemble and install new pipe organs and pianos in buildings.
- Reassemble instruments following repair, using hand tools and power tools and glue, hair, yarn, resin, or clamps, and lubricate instruments as necessary.
- Adjust string tensions to tune instruments, using hand tools and electronic tuning devices.
- Compare instrument pitches with tuning tool pitches to tune instruments.
- Play instruments to evaluate their sound quality and to locate any defects.
- Disassemble instruments and parts for repair and adjustment.
- Repair or replace musical instrument parts and components, such as strings, bridges, felts, and keys, using hand and power tools.
- Inspect instruments to locate defects, and to determine their value or the level of restoration required.
- Shape old parts and replacement parts to improve tone or intonation, using hand tools, lathes, or soldering irons.
- String instruments, and adjust trusses and bridges of instruments to obtain specified string tensions and heights.
- Repair cracks in wood or metal instruments, using pinning wire, lathes, fillers, clamps, or soldering irons.
- Polish instruments, using rags and polishing compounds, buffing wheels, or burnishing tools.
- Mix and measure glue that will be used for instrument repair.
- Align pads and keys on reed or wind instruments.
- Solder posts and parts to hold them in their proper places.
- Remove dents and burrs from metal instruments, using mallets and burnishing tools.
- Adjust felt hammers on pianos to increase tonal mellowness or brilliance, using sanding paddles, lacquer, or needles.
- Remove irregularities from tuning pins, strings, and hammers of pianos, using wood blocks or filing tools.
- Strike wood, fiberglass, or metal bars of instruments, and use tuned blocks, stroboscopes, or electronic tuners to evaluate tones made by instruments.
- Make wood replacement parts, using woodworking machines and hand tools.
- Refinish instruments to protect and decorate them, using hand tools, buffing tools, and varnish.
- Deliver pianos to purchasers or to locations of their use.
- Wash metal instruments in lacquer-stripping and cyanide solutions to remove lacquer and tarnish.
- Refinish and polish piano cabinets or cases to prepare them for sale.
- Adjust the neck angle on fretted instruments.
- Assemble and install new pipe organs and pianos in buildings.
- Reassemble instruments following repair, using hand tools and power tools and glue, hair, yarn, resin, or clamps, and lubricate instruments as necessary.
- Install gas burners to convert furnaces from wood, coal, or oil.
- Fit or assist in fitting valves, couplings, or assemblies to tanks, pumps, or systems, using hand tools.
- Mount brackets and hangers on walls and ceilings to hold pipes, and set sleeves or inserts to provide support for pipes.
- Perform rough-ins, repair and replace fixtures and water heaters, and locate, repair, or remove leaking or broken pipes.
- Cut pipe and lift up to fitters.
- Measure, cut, thread and assemble new pipe, placing the assembled pipe in hangers or other supports.
- Assist pipe fitters in the layout, assembly, and installation of piping for air, ammonia, gas, and water systems.
- Requisition tools and equipment, select type and size of pipe, and collect and transport materials and equipment to work site.
- Disassemble and remove damaged or worn pipe.
- Cut or drill holes in walls or floors to accommodate the passage of pipes.
- Clean shop, work area, and machines, using solvent and rags.
- Excavate and grade ditches, and lay and join pipe for water and sewer service.
- Immerse pipe in chemical solution to remove dirt, oil, and scale.
- Clean and renew steam traps.
- Fill pipes with sand or resin to prevent distortion, and hold pipes during bending and installation.
- Install gas burners to convert furnaces from wood, coal, or oil.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Maintain equipment, making repairs or modifications when necessary.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Transport prefabricated parts to construction sites for assembly and installation.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Hire, train, or supervise new employees or apprentices.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Fabricate or alter parts at construction sites, using shears, hammers, punches, or drills.
- Determine project requirements, such as scope, assembly sequences, or required methods or materials, using blueprints, drawings, or written or verbal instructions.
- Maneuver completed roofing units into position for installation.
- Select gauges or types of sheet metal or nonmetallic material, according to product specifications.
- Shape metal material over anvils, blocks, or other forms, using hand tools.
- Trim, file, grind, deburr, buff, or smooth surfaces, seams, or joints of assembled parts, using hand tools or portable power tools.
- Inspect individual parts, assemblies, or installations, using measuring instruments, such as calipers, scales, or micrometers.
- Convert blueprints into shop drawings to be followed in the construction or assembly of sheet metal products.
- Verify that heating, ventilating, and air conditioning (HVAC) systems are designed, installed, and calibrated in accordance with green certification standards, such as those of Leadership in Energy and Environmental Design (LEED).
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Finish parts, using hacksaws or hand, rotary, or squaring shears.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Train crews, and introduce procedures to make drill work more safe and effective.
- Observe pressure gauge and move throttles and levers to control the speed of rotary tables, and to regulate pressure of tools at bottoms of boreholes.
- Maintain records of footage drilled, location and nature of strata penetrated, materials and tools used, services rendered, and time required.
- Push levers and brake pedals to control gasoline, diesel, electric, or steam draw works that lower and raise drill pipes and casings in and out of wells.
- Connect sections of drill pipe, using hand tools and powered wrenches and tongs.
- Count sections of drill rod to determine depths of boreholes.
- Maintain and adjust machinery to ensure proper performance.
- Direct rig crews in drilling and other activities, such as setting up rigs and completing or servicing wells.
- Weigh clay, and mix with water and chemicals to make drilling mud.
- Start and examine operation of slush pumps to ensure circulation and consistency of drilling fluid or mud in well.
- Clean and oil pulleys, blocks, and cables.
- Monitor progress of drilling operations, and select and change drill bits according to the nature of strata, using hand tools.
- Repair or replace defective parts of machinery, such as rotary drill rigs, water trucks, air compressors, and pumps, using hand tools.
- Locate and recover lost or broken bits, casings, and drill pipes from wells, using special tools.
- Line drilled holes with pipes, and install all necessary hardware, to prepare new wells.
- Cap wells with packers, or turn valves, to regulate outflow of oil from wells.
- Remove core samples during drilling to determine the nature of the strata being drilled.
- Plug observation wells, and restore sites.
- Position and prepare truck-mounted derricks at drilling areas specified on field maps.
- Lower and explode charges in boreholes to start flow of oil from wells.
- Inspect safety equipment, such as harnesses, belts, and lifelines, before use.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Assemble and position machines, augers, casing pipes, and other equipment, using hand and power tools.
- Operate controls to stabilize machines and to position and align drills.
- Start, stop, and control drilling speed of machines and insertion of casings into holes.
- Regulate air pressure, rotary speed, and downward pressure, according to the type of rock or concrete being drilled.
- Select and attach drill bits and drill rods, adding more rods as hole depths increase, and changing drill bits as needed.
- Drive or guide truck-mounted equipment into position, level and stabilize rigs, and extend telescoping derricks.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Verify depths and alignments of boring positions.
- Perform routine maintenance and upgrade work on machines and equipment, such as replacing parts, building up drill bits, and lubricating machinery.
- Select the appropriate drill for the job, using knowledge of rock or soil conditions.
- Document geological formations encountered during work.
- Drive trucks, tractors, or truck-mounted drills to and from work sites.
- Record drilling progress and geological data.
- Retrieve lost equipment from bore holes, using retrieval tools and equipment.
- Fabricate well casings.
- Pour water into wells, or pump water or slush into wells to cool drill bits and to remove drillings.
- Create and lay out designs for drill and blast patterns.
- Place and install screens, casings, pumps, and other well fixtures to develop wells.
- Operate water-well drilling rigs and other equipment to drill, bore, and dig for water wells or for environmental assessment purposes.
- Review client requirements and proposed locations for drilling operations to determine feasibility, and to determine cost estimates.
- Drill or bore holes in rock for blasting, grouting, anchoring, or building foundations.
- Perform pumping tests to assess well performance.
- Disinfect, reconstruct, and redevelop contaminated wells and water pumping systems, and clean and disinfect new wells in preparation for use.
- Design well pumping systems.
- Signal crane operators to move equipment.
- Withdraw drill rods from holes, and extract core samples.
- Inspect core samples to determine nature of strata, or take samples to laboratories for analysis.
- Retract augers to force discharge dirt from holes.
- Monitor drilling operations, by checking gauges and listening to equipment to assess drilling conditions and to determine the need to adjust drilling or alter equipment.
- Assemble and position machines, augers, casing pipes, and other equipment, using hand and power tools.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
- Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
- Follow established safety rules and regulations and maintain a safe and clean environment.
- Shape or cut materials to specified measurements, using hand tools, machines, or power saws.
- Select and order lumber or other required materials.
- Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.
- Verify trueness of structure, using plumb bob and level.
- Arrange for subcontractors to deal with special areas, such as heating or electrical wiring work.
- Build or repair cabinets, doors, frameworks, floors, or other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, or power tools.
- Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.
- Install rough door and window frames, subflooring, fixtures, or temporary supports in structures undergoing construction or repair.
- Erect scaffolding or ladders for assembling structures above ground level.
- Maintain job records and schedule work crew.
- Examine structural timbers and supports to detect decay, and replace timbers as required, using hand tools, nuts, and bolts.
- Fill cracks or other defects in plaster or plasterboard and sand patch, using patching plaster, trowel, and sanding tool.
- Dig or direct digging of post holes and set poles to support structures.
- Finish surfaces of woodwork or wallboard in houses or buildings, using paint, hand tools, or paneling.
- Cover subfloors with building paper to keep out moisture and lay hardwood, parquet, or wood-strip-block floors by nailing floors to subfloor or cementing them to mastic or asphalt base.
- Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.
- Prepare cost estimates for clients or employers.
- Maintain records, document actions, and present written progress reports.
- Bore boltholes in timber, masonry or concrete walls, using power drill.
- Study specifications in blueprints, sketches, or building plans to prepare project layout and determine dimensions and materials required.
- Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue.
- Perform minor plumbing, welding, or concrete mixing work.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Work with or remove hazardous material.
- Construct forms or chutes for pouring concrete.
- Apply shock-absorbing, sound-deadening, or decorative paneling to ceilings or walls.
- Use drones for site surveying and to inspect hard-to-reach areas of a structure.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
