- Locate and remove or repair circuit defects such as blown fuses or malfunctioning transistors.
Occupations with related tasks Save Table: XLSX CSV
- Repair circuits, wiring, and soldering, using soldering irons and hand tools to install parts and adjust connections.
- Install or repair tower lighting components, including strobes, beacons, or lighting controllers.
- Remove and replace defective components and parts such as conductors, resistors, semiconductors, and integrated circuits, using soldering irons, wire cutters, and hand tools.
- Test batteries, using hydrometers and ammeters, and charge batteries as necessary.
- Inspect completed work to ensure all hardware is tight, antennas are level, hangers are properly fastened, proper support is in place, or adequate weather proofing has been installed.
- Run appropriate power, ground, or coaxial cables.
- Test operation of tower transmission components, using sweep testing tools or software.
- Install all necessary transmission equipment components, including antennas or antenna mounts, surge arrestors, transmission lines, connectors, or tower-mounted amplifiers (TMAs).
- Read work orders, blueprints, plans, datasheets or site drawings to determine work to be done.
- Replace existing antennas with new antennas as directed.
- Bolt equipment into place, using hand or power tools.
- Install, connect, or test underground or aboveground grounding systems.
- Complete reports related to project status, progress, or other work details, using computer software.
- Check antenna positioning to ensure specified azimuths or mechanical tilts and adjust as necessary.
- Transport equipment to work sites, using utility trucks and equipment trailers.
- Take site survey photos or photos of work performed, using digital cameras.
- Climb towers to access components, using safety equipment, such as full-body harnesses.
- Climb communication towers to install, replace, or repair antennas or auxiliary equipment used to transmit and receive radio waves.
- Lift equipment into position, using cranes and rigging tools or equipment, such as gin poles.
- Perform maintenance or repair work on existing tower equipment, using hand or power tools.
- Locate tower sites where work is to be performed, using mapping software.
- Calibrate and align components, using scales, gauges, and other measuring instruments.
- Examine malfunctioning radio equipment to locate defects such as loose connections, broken wires, or burned-out components, using schematic diagrams and test equipment.
- Insert plugs into receptacles and bolt or screw leads to terminals to connect equipment to power sources, using hand tools.
- Install, adjust, and repair stationary and mobile radio transmitting and receiving equipment and two-way radio communication systems.
- Monitor radio range stations to detect transmission flaws and adjust controls to eliminate flaws.
- Mount equipment on transmission towers and in vehicles such as ships or ambulances.
- Test emergency transmitters to ensure their readiness for immediate use.
- Test equipment functions such as signal strength and quality, transmission capacity, interference, and signal delay, using equipment such as oscilloscopes, circuit analyzers, frequency meters, and wattmeters.
- Turn setscrews to adjust receivers for maximum sensitivity and transmitters for maximum output.
- Repair circuits, wiring, and soldering, using soldering irons and hand tools to install parts and adjust connections.
- Install or repair tower lighting components, including strobes, beacons, or lighting controllers.
- Remove and replace defective components and parts such as conductors, resistors, semiconductors, and integrated circuits, using soldering irons, wire cutters, and hand tools.
- Test batteries, using hydrometers and ammeters, and charge batteries as necessary.
- Open and close switches to isolate defective relays, performing adjustments or repairs.
- Repair, replace, and clean equipment and components such as circuit breakers, brushes, and commutators.
- Construct, test, maintain, and repair substation relay and control systems.
- Inspect and test equipment and circuits to identify malfunctions or defects, using wiring diagrams and testing devices such as ohmmeters, voltmeters, or ammeters.
- Prepare and maintain records detailing tests, repairs, and maintenance.
- Consult manuals, schematics, wiring diagrams, and engineering personnel to troubleshoot and solve equipment problems and to determine optimum equipment functioning.
- Analyze test data to diagnose malfunctions, to determine performance characteristics of systems, or to evaluate effects of system modifications.
- Notify facility personnel of equipment shutdowns.
- Run signal quality and connectivity tests for individual cables, and record results.
- Maintain inventories of spare parts for all equipment, requisitioning parts as necessary.
- Test insulators and bushings of equipment by inducing voltage across insulation, testing current, and calculating insulation loss.
- Schedule and supervise the construction and testing of special devices and the implementation of unique monitoring or control systems.
- Schedule and supervise splicing or termination of cables in color-code order.
- Test oil in circuit breakers and transformers for dielectric strength, refilling oil periodically.
- Disconnect voltage regulators, bolts, and screws, and connect replacement regulators to high-voltage lines.
- Set forms and pour concrete footings for installation of heavy equipment.
- Open and close switches to isolate defective relays, performing adjustments or repairs.
- Repair, replace, and clean equipment and components such as circuit breakers, brushes, and commutators.
- Construct, test, maintain, and repair substation relay and control systems.
- Test and repair circuits and sensors, following wiring and system specifications.
- Install, maintain, or repair security systems, alarm devices, or related equipment, following blueprints of electrical layouts and building plans.
- Mount and fasten control panels, door and window contacts, sensors, or video cameras, and attach electrical and telephone wiring to connect components.
- Demonstrate systems for customers and explain details, such as the causes and consequences of false alarms.
- Feed cables through access holes, roof spaces, or cavity walls to reach fixture outlets, positioning and terminating cables, wires, or strapping.
- Examine systems to locate problems, such as loose connections or broken insulation.
- Test backup batteries, keypad programming, sirens, or other security features to ensure proper functioning or to diagnose malfunctions.
- Drill holes for wiring in wall studs, joists, ceilings, or floors.
- Inspect installation sites and study work orders, building plans, and installation manuals to determine materials requirements and installation procedures.
- Consult with clients to assess risks and to determine security requirements.
- Mount raceways and conduits and fasten wires to wood framing, using staplers.
- Adjust sensitivity of units, based on room structures and manufacturers' recommendations, using programming keypads.
- Keep informed of new products and developments.
- Order replacement parts.
- Prepare documents, such as invoices or warranties.
- Provide customers with cost estimates for equipment installation.
- Test and repair circuits and sensors, following wiring and system specifications.
- Install, maintain, or repair security systems, alarm devices, or related equipment, following blueprints of electrical layouts and building plans.
- Trace and tag meters or house lines.
- Repair electric meters and components, such as transformers and relays, and replace metering devices, dial glasses, and faulty or incorrect wiring, using hand tools.
- Record maintenance information, including test results, material usage, and repairs made.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Lubricate wearing surfaces of mechanical parts, using oils or other lubricants.
- Calibrate instrumentation, such as meters, gauges, and regulators, for pressure, temperature, flow, and level.
- Install, inspect and test electric meters, relays, and power sources to detect causes of malfunctions and inaccuracies, using hand tools and testing equipment.
- Test valves and regulators for leaks and accurate temperature and pressure settings, using precision testing equipment.
- Record meter readings and installation data on meter cards, work orders, or field service orders, or enter data into hand-held computers.
- Turn meters on or off to establish or close service.
- Shut off service and notify repair crews when major repairs are required, such as the replacement of underground pipes or wiring.
- Install regulators and related equipment such as gas meters, odorization units, and gas pressure telemetering equipment.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Turn valves to allow measured amounts of air or gas to pass through meters at specified flow rates.
- Report hazardous field situations and damaged or missing meters.
- Vary air pressure flowing into regulators and turn handles to assess functioning of valves and pistons.
- Examine valves or mechanical control device parts for defects, dents, or loose attachments, and mark malfunctioning areas of defective units.
- Mount and install meters and other electric equipment such as time clocks, transformers, and circuit breakers, using electricians' hand tools.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Investigate instances of illegal tapping into service lines.
- Replace defective parts, such as bellows, range springs, and toggle switches, and reassemble units according to blueprints, using cam presses and hand tools.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Measure tolerances of assembled and salvageable parts for conformance to standards or specifications, using gauges, micrometers, and calipers.
- Clean internal compartments and moving parts, using rags and cleaning compounds.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Reassemble repaired equipment, and solder top, front, and back case panels in place, using soldering guns, power tools, and hand tools.
- Attach air hoses to meter inlets, plug outlets, and observe gauges for pressure losses to test internal seams for leaks.
- Make adjustments to meter components, such as setscrews or timing mechanisms, so that they conform to specifications.
- Recommend and write up specifications for changes in hardware, such as house wiring.
- Clamp regulator units into vises on stages above water tanks, and attach compressed air hoses to intake ports.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Collect money due on delinquent accounts.
- Splice and connect cables from meters or current transformers to pull boxes or switchboards, using hand tools.
- Attach pressurized meters to fixtures which submerge them in water, and observe meters for leaks.
- Advise customers on proper installation of valves or regulators and related equipment.
- Calibrate thermostats for specified temperature or pressure settings.
- Clean plant growth, scale, paint, soil, or rust from meter housings, using wire brushes, scrapers, buffers, sandblasters, or cleaning compounds.
- Connect hoses from provers to meter inlets and outlets, and raise prover bells until prover gauges register zero.
- Trace and tag meters or house lines.
- Repair electric meters and components, such as transformers and relays, and replace metering devices, dial glasses, and faulty or incorrect wiring, using hand tools.
- Adjust generators and replace faulty wiring, using hand tools and soldering irons.
- Start motors and monitor performance for signs of malfunctioning, such as smoke, excessive vibration, or misfiring.
- Document inspection and test results and work performed or to be performed.
- Mount motors to boats, and operate boats at various speeds on waterways to conduct operational tests.
- Repair engine mechanical equipment, such as power tilts, bilge pumps, or power take-offs.
- Perform routine engine maintenance on motorboats, such as changing oil and filters.
- Replace parts, such as gears, magneto points, piston rings, or spark plugs, and reassemble engines.
- Idle motors and observe thermometers to determine the effectiveness of cooling systems.
- Inspect and repair or adjust propellers or propeller shafts.
- Adjust carburetor mixtures, electrical point settings, or timing while motors are running in water-filled test tanks.
- Set starter locks and align and repair steering or throttle controls, using gauges, screwdrivers, or wrenches.
- Disassemble and inspect motors to locate defective parts, using mechanic's hand tools and gauges.
- Repair or rework parts, using machine tools such as lathes, mills, drills, or grinders.
- Adjust generators and replace faulty wiring, using hand tools and soldering irons.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, and hand tools.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Move and set up mobile homes or prefabricated buildings on owners' lots or at mobile home parks.
- Inspect, examine, and test the operation of parts or systems to evaluate operating condition and to determine if repairs are needed.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of plumbing fixtures.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, and diagrams.
- Confer with customers or read work orders to determine the nature and extent of damage to units.
- Install, repair, and replace units, fixtures, appliances, and other items and systems in mobile and modular homes, prefabricated buildings, or travel trailers, using hand tools or power tools.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Repair leaks in plumbing or gas lines, using caulking compounds and plastic or copper pipe.
- Open and close doors, windows, and drawers to test their operation, trimming edges to fit, using jackplanes or drawknives.
- Connect electrical systems to outside power sources and activate switches to test the operation of appliances and light fixtures.
- Refinish wood surfaces on cabinets, doors, moldings, and floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, and hand tools.
- Inspect electrical units of railroad grade crossing gates and repair loose bolts and defective electrical connections and parts.
- Inspect and test operation, mechanical parts, and circuitry of gate crossings, signals, and signal equipment such as interlocks and hotbox detectors.
- Test and repair track circuits.
- Drive motor vehicles to job sites.
- Install, inspect, maintain, and repair various railroad service equipment on the road or in the shop, including railroad signal systems.
- Tighten loose bolts, using wrenches, and test circuits and connections by opening and closing gates.
- Inspect switch-controlling mechanisms on trolley wires and in track beds, using hand tools and test equipment.
- Replace defective wiring, broken lenses, or burned-out light bulbs.
- Inspect, maintain, and replace batteries as needed.
- Record and report information about mileage or track inspected, repairs performed, and equipment requiring replacement.
- Lubricate moving parts on gate-crossing mechanisms and swinging signals.
- Clean lenses of lamps with cloths and solvents.
- Test air lines and air cylinders on pneumatically operated gates.
- Maintain high tension lines, de-energizing lines for power companies when repairs are requested.
- Inspect electrical units of railroad grade crossing gates and repair loose bolts and defective electrical connections and parts.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, or hand tools.
- Explain proper operation of vehicle systems to customers.
- Repair plumbing or propane gas lines, using caulking compounds and plastic or copper pipe.
- Confer with customers, read work orders, or examine vehicles needing repair to determine the nature and extent of damage.
- Examine or test operation of parts or systems to ensure completeness of repairs.
- Connect electrical systems to outside power sources, and activate switches to test the operation of appliances or light fixtures.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of toilets or sinks.
- Inspect recreational vehicles to diagnose problems and perform necessary adjustment, repair, or overhaul.
- Inspect, repair, or replace brake systems.
- Diagnose and repair furnace or air conditioning systems.
- Repair leaks with caulking compound or replace pipes, using pipe wrenches.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, or diagrams.
- Remove damaged exterior panels, and repair and replace structural frame members.
- Open and close doors, windows, or drawers to test their operation, trimming edges to fit, as necessary.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Refinish wood surfaces on cabinets, doors, moldings, or floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, or hand tools.
- Install, maintain, and repair electrical distribution and transmission systems, including conduits, cables, wires, and related equipment, such as transformers, circuit breakers, and switches.
- Adhere to safety practices and procedures, such as checking equipment regularly and erecting barriers around work areas.
- Drive vehicles equipped with tools and materials to job sites.
- Open switches or attach grounding devices to remove electrical hazards from disturbed or fallen lines or to facilitate repairs.
- Climb poles or use truck-mounted buckets to access equipment.
- Inspect and test power lines and auxiliary equipment to locate and identify problems, using reading and testing instruments.
- Coordinate work assignment preparation and completion with other workers.
- Replace or straighten damaged poles.
- String wire conductors and cables between poles, towers, trenches, pylons, and buildings, setting lines in place and using winches to adjust tension.
- Attach cross-arms, insulators, and auxiliary equipment to poles prior to installing them.
- Dig holes, using augers, and set poles, using cranes and power equipment.
- Travel in trucks, helicopters, and airplanes to inspect lines for freedom from obstruction and adequacy of insulation.
- Identify defective sectionalizing devices, circuit breakers, fuses, voltage regulators, transformers, switches, relays, or wiring, using wiring diagrams and electrical-testing instruments.
- Install watt-hour meters and connect service drops between power lines and consumers' facilities.
- Test conductors, according to electrical diagrams and specifications, to identify corresponding conductors and to prevent incorrect connections.
- Place insulating or fireproofing materials over conductors and joints.
- Splice or solder cables together or to overhead transmission lines, customer service lines, or street light lines, using hand tools, epoxies, or specialized equipment.
- Trim trees that could be hazardous to the functioning of cables or wires.
- Pull up cable by hand from large reels mounted on trucks.
- Lay underground cable directly in trenches, or string it through conduit running through the trenches.
- Cut trenches for laying underground cables, using trenchers and cable plows.
- Cut and peel lead sheathing and insulation from defective or newly installed cables and conduits prior to splicing.
- Clean, tin, and splice corresponding conductors by twisting ends together or by joining ends with metal clamps and soldering connections.
- Install, maintain, and repair electrical distribution and transmission systems, including conduits, cables, wires, and related equipment, such as transformers, circuit breakers, and switches.
- Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.
- Perform routine maintenance, such as inspecting drives, motors, or belts, checking fluid levels, replacing filters, or doing other preventive maintenance actions.
- Inspect, operate, or test machinery or equipment to diagnose machine malfunctions.
- Adjust functional parts of devices or control instruments, using hand tools, levels, plumb bobs, or straightedges.
- Order parts, supplies, or equipment from catalogs or suppliers.
- Diagnose mechanical problems and determine how to correct them, checking blueprints, repair manuals, or parts catalogs, as necessary.
- Design new equipment to aid in the repair or maintenance of machines, mechanical equipment, or building structures.
- Clean or lubricate shafts, bearings, gears, or other parts of machinery.
- Estimate costs to repair machinery, equipment, or building structures.
- Align and balance new equipment after installation.
- Record type and cost of maintenance or repair work.
- Maintain or repair specialized equipment or machinery located in cafeterias, laundries, hospitals, stores, offices, or factories.
- Dismantle machines, equipment, or devices to access and remove defective parts, using hoists, cranes, hand tools, or power tools.
- Plan and lay out repair work, using diagrams, drawings, blueprints, maintenance manuals, or schematic diagrams.
- Install equipment to improve the energy or operational efficiency of residential or commercial buildings.
- Set up and operate machine tools to repair or fabricate machine parts, jigs, fixtures, or tools.
- Perform general cleaning of buildings or properties.
- Train or manage maintenance personnel or subcontractors.
- Fabricate or repair counters, benches, partitions, or other wooden structures, such as sheds or outbuildings.
- Paint or repair roofs, windows, doors, floors, woodwork, plaster, drywall, or other parts of building structures.
- Perform routine maintenance on boilers, such as replacing burners or hoses, installing replacement parts, or reinforcing structural weaknesses to ensure optimal boiler efficiency.
- Test and treat water supply.
- Provide groundskeeping services, such as landscaping or snow removal.
- Operate cutting torches or welding equipment to cut or join metal parts.
- Inspect used parts to determine changes in dimensional requirements, using rules, calipers, micrometers, or other measuring instruments.
- Assemble boilers at installation sites, using tools such as levels, plumb bobs, hammers, torches, or other hand tools.
- Lay brick to repair or maintain buildings, walls, arches, or other structures.
- Position, attach, or blow insulating materials to prevent energy losses from buildings, pipes, or other structures or objects.
- Grind and reseat valves, using valve-grinding machines.
- Repair machines, equipment, or structures, using tools such as hammers, hoists, saws, drills, wrenches, or equipment such as precision measuring instruments or electrical or electronic testing devices.
- Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.
