Job Duties Custom List 47-2011.00 — Boilermakers
- Inspect assembled vessels or individual components, such as tubes, fittings, valves, controls, or auxiliary mechanisms, to locate any defects.
Occupations with related tasks Save Table: XLSX CSV
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Check that safety regulations and building codes are met, and complete service reports verifying conformance to standards.
- Connect electrical wiring to control panels and electric motors.
- Adjust safety controls, counterweights, door mechanisms, and components such as valves, ratchets, seals, and brake linings.
- Read and interpret blueprints to determine the layout of system components, frameworks, and foundations, and to select installation equipment.
- Disassemble defective units, and repair or replace parts such as locks, gears, cables, and electric wiring.
- Maintain log books that detail all repairs and checks performed.
- Participate in additional training to keep skills up to date.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Connect car frames to counterweights, using steel cables.
- Bolt or weld steel rails to the walls of shafts to guide elevators, working from scaffolding or platforms.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Install outer doors and door frames at elevator entrances on each floor of a structure.
- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
- Cut prefabricated sections of framework, rails, and other components to specified dimensions.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Examine lifting or conveying devices, such as elevators, escalators, moving sidewalks, hoists, inclined railways, ski lifts, or amusement rides to ensure safety and proper functioning.
- Inspect bridges, dams, highways, buildings, wiring, plumbing, electrical circuits, sewers, heating systems, or foundations during and after construction for structural quality, general safety, or conformance to specifications and codes.
- Monitor installation of plumbing, wiring, equipment, or appliances to ensure that installation is performed properly and is in compliance with applicable regulations.
- Approve building plans that meet required specifications.
- Inspect and monitor construction sites to ensure adherence to safety standards, building codes, or specifications.
- Review and interpret plans, blueprints, site layouts, specifications, or construction methods to ensure compliance to legal requirements and safety regulations.
- Maintain daily logs and supplement inspection records with photographs.
- Conduct inspections, using survey instruments, metering devices, tape measures, or test equipment.
- Measure dimensions and verify level, alignment, or elevation of structures or fixtures to ensure compliance to building plans and codes.
- Train, direct, or supervise other construction inspectors.
- Confer with owners, violators, or authorities to explain regulations or recommend remedial actions.
- Issue permits for construction, relocation, demolition, or occupancy.
- Conduct environmental hazard inspections to identify or quantify problems, such as asbestos, poor air quality, water contamination, or other environmental hazards.
- Evaluate premises for cleanliness, such as proper garbage disposal or lack of vermin infestation.
- Monitor construction activities to ensure that environmental regulations are not violated.
- Evaluate project details to ensure adherence to environmental regulations.
- Estimate cost of completed work or of needed renovations or upgrades.
- Sample and test air to identify gasses, such as bromine, ozone, or sulfur dioxide, or particulates, such as mold, dust, or allergens.
- Inspect facilities or installations to determine their environmental impact.
- Examine lifting or conveying devices, such as elevators, escalators, moving sidewalks, hoists, inclined railways, ski lifts, or amusement rides to ensure safety and proper functioning.
- Inspect bridges, dams, highways, buildings, wiring, plumbing, electrical circuits, sewers, heating systems, or foundations during and after construction for structural quality, general safety, or conformance to specifications and codes.
- Test and diagnose air flow systems, using furnace efficiency analysis equipment.
- Determine amount of air leakage in buildings, using a blower door machine.
- Test combustible appliances, such as gas appliances.
- Install and seal air ducts, combustion air openings, or ventilation openings to improve heating and cooling efficiency.
- Inspect buildings to identify required weatherization measures, including repair work, modification, or replacement.
- Recommend weatherization techniques to clients in accordance with needs and applicable energy regulations, codes, policies, or statutes.
- Apply insulation materials, such as loose, blanket, board, and foam insulation to attics, crawl spaces, basements, or walls.
- Make minor repairs using basic hand or power tools and materials, such as glass, lumber, and drywall.
- Prepare cost estimates or specifications for rehabilitation or weatherization services.
- Contact residents or building owners to schedule appointments.
- Wrap air ducts and water lines with insulating materials, such as duct wrap and pipe insulation.
- Prepare and apply weather-stripping, glazing, caulking, or door sweeps to reduce energy losses.
- Clean and maintain tools and equipment.
- Apply spackling, compounding, or other materials to repair holes in walls.
- Explain recommendations, policies, procedures, requirements, or other related information to residents or building owners.
- Maintain activity logs, financial transaction logs, or other records of weatherization work performed.
- Explain energy conservation measures, such as the use of low flow showerheads and energy-efficient lighting.
- Prepare or assist in the preparation of bids, contracts, or written reports related to weatherization work.
- Install storm windows or storm doors and verify proper fit.
- Wrap water heaters with water heater blankets.
- Test and diagnose air flow systems, using furnace efficiency analysis equipment.
- Determine amount of air leakage in buildings, using a blower door machine.
- Test operation or functionality of mechanical, plumbing, electrical, and control systems.
- Fill water tanks and check tanks, pipes, and fittings for leaks.
- Apply weather seal, such as pipe flashings and sealants, to roof penetrations and structural devices.
- Install solar collector mounting devices on tile, asphalt, shingle, or built-up gravel roofs, using appropriate materials and penetration methods.
- Install copper or plastic plumbing using pipes, fittings, pipe cutters, acetylene torches, solder, wire brushes, sand cloths, flux, plastic pipe cleaners, or plastic glue.
- Identify plumbing, electrical, environmental, or safety hazards associated with solar thermal installations.
- Demonstrate start-up, shut-down, maintenance, diagnostic, and safety procedures to thermal system owners.
- Install circulating pumps using pipe, fittings, soldering equipment, electrical supplies, and hand tools.
- Install flat-plat, evacuated glass, or concentrating solar collectors on mounting devices, using brackets or struts.
- Install solar thermal system controllers and sensors.
- Design active direct or indirect, passive direct or indirect, or pool solar systems.
- Determine locations for installing solar subsystem components, including piping, water heaters, valves, and ancillary equipment.
- Perform routine maintenance or repairs to restore solar thermal systems to baseline operating conditions.
- Install heat exchangers and heat exchanger fluids according to installation manuals and schematics.
- Apply operation or identification tags or labels to system components, as required.
- Connect water heaters and storage tanks to power and water sources.
- Cut, miter, and glue piping insulation to insulate plumbing pipes and fittings.
- Install plumbing, such as dip tubes, port fittings, drain tank valves, pressure temperature relief valves, or tanks, according to manufacturer specifications and building codes.
- Install monitoring system components, such as flow meters, temperature gauges, and pressure gauges, according to system design and manufacturer specifications.
- Assess collector sites to ensure structural integrity of potential mounting surfaces or the best orientation and tilt for solar collectors.
- Apply ultraviolet radiation protection to prevent degradation of plumbing.
- Test operation or functionality of mechanical, plumbing, electrical, and control systems.
- Fill water tanks and check tanks, pipes, and fittings for leaks.
- Inspect, clean, and repair drainage systems, bridges, tunnels, and other structures.
- Set out signs and cones around work areas to divert traffic.
- Flag motorists to warn them of obstacles or repair work ahead.
- Perform preventative maintenance on vehicles and heavy equipment.
- Drive trucks to transport crews and equipment to work sites.
- Erect, install, or repair guardrails, road shoulders, berms, highway markers, warning signals, and highway lighting, using hand tools and power tools.
- Clean and clear debris from culverts, catch basins, drop inlets, ditches, and other drain structures.
- Drive heavy equipment and vehicles with adjustable attachments to sweep debris from paved surfaces, mow grass and weeds, remove snow and ice, and spread salt and sand.
- Haul and spread sand, gravel, and clay to fill washouts and repair road shoulders.
- Remove litter and debris from roadways, including debris from rock and mud slides.
- Dump, spread, and tamp asphalt, using pneumatic tampers, to repair joints and patch broken pavement.
- Perform roadside landscaping work, such as clearing weeds and brush, and planting and trimming trees.
- Apply poisons along roadsides and in animal burrows to eliminate unwanted roadside vegetation and rodents.
- Measure and mark locations for installation of markers, using tape, string, or chalk.
- Paint traffic control lines and place pavement traffic messages, by hand or using machines.
- Apply oil to road surfaces, using sprayers.
- Inspect markers to verify accurate installation.
- Place and remove snow fences used to prevent the accumulation of drifting snow on highways.
- Blend compounds to form adhesive mixtures used for marker installation.
- Inspect, clean, and repair drainage systems, bridges, tunnels, and other structures.
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
- Convert blueprints into shop drawings to be followed in the construction or assembly of sheet metal products.
- Determine project requirements, such as scope, assembly sequences, or required methods or materials, using blueprints, drawings, or written or verbal instructions.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Trim, file, grind, deburr, buff, or smooth surfaces, seams, or joints of assembled parts, using hand tools or portable power tools.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Select gauges or types of sheet metal or nonmetallic material, according to product specifications.
- Finish parts, using hacksaws or hand, rotary, or squaring shears.
- Shape metal material over anvils, blocks, or other forms, using hand tools.
- Fabricate or alter parts at construction sites, using shears, hammers, punches, or drills.
- Transport prefabricated parts to construction sites for assembly and installation.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Hire, train, or supervise new employees or apprentices.
- Maintain equipment, making repairs or modifications when necessary.
- Develop or lay out patterns, using computerized metalworking equipment.
- Maneuver completed roofing units into position for installation.
- Inspect individual parts, assemblies, or installations, using measuring instruments, such as calipers, scales, or micrometers.
- Verify that heating, ventilating, and air conditioning (HVAC) systems are designed, installed, and calibrated in accordance with green certification standards, such as those of Leadership in Energy and Environmental Design (LEED).
- Secure metal roof panels in place by interlocking and fastening grooved panel edges.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Perform sheet metal work necessary for solar panel installations.
- Install green architectural sheet metal components, such as cool roofs or hot or cold walls.
- Construct components for high-performance wind turbine systems.
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
