- Assemble and position machines, augers, casing pipes, and other equipment, using hand and power tools.
Occupations with related tasks Save Table: XLSX CSV
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Connect car frames to counterweights, using steel cables.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Disassemble defective units, and repair or replace parts such as locks, gears, cables, and electric wiring.
- Check that safety regulations and building codes are met, and complete service reports verifying conformance to standards.
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Adjust safety controls, counterweights, door mechanisms, and components such as valves, ratchets, seals, and brake linings.
- Read and interpret blueprints to determine the layout of system components, frameworks, and foundations, and to select installation equipment.
- Maintain log books that detail all repairs and checks performed.
- Connect electrical wiring to control panels and electric motors.
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Participate in additional training to keep skills up to date.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
- Install outer doors and door frames at elevator entrances on each floor of a structure.
- Bolt or weld steel rails to the walls of shafts to guide elevators, working from scaffolding or platforms.
- Cut prefabricated sections of framework, rails, and other components to specified dimensions.
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Connect car frames to counterweights, using steel cables.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Insert waterproof sealers, bullets, and/or powder charges into guns, and screw gun ports back into place.
- Lower perforating guns into wells, using hoists; then use measuring devices and instrument panels to position guns in correct positions for taking samples.
- Insert powder charges into chambers of sidewall sample-taking cylinders, and assemble cylinders, using special wrenches.
- Place safety cones around blast areas to alert other workers of danger zones, and signal workers as necessary to ensure that they clear blast sites prior to explosions.
- Examine blast areas to determine amounts and kinds of explosive charges needed and to ensure that safety laws are observed.
- Tie specified lengths of delaying fuses into patterns in order to time sequences of explosions.
- Place explosive charges in holes or other spots; then detonate explosives to demolish structures or to loosen, remove, or displace earth, rock, or other materials.
- Insert, pack, and pour explosives, such as dynamite, ammonium nitrate, black powder, or slurries into blast holes; then shovel drill cuttings, admit water into boreholes, and tamp material to compact charges.
- Mark patterns, locations, and depths of charge holes for drilling, and issue drilling instructions.
- Compile and keep gun and explosives records in compliance with local and federal laws.
- Measure depths of drilled blast holes, using weighted tape measures.
- Connect electrical wire to primers, and cover charges or fill blast holes with clay, drill chips, sand, or other material.
- Lay primacord between rows of charged blast holes, and tie cord into main lines to form blast patterns.
- Verify detonation of charges by observing control panels, or by listening for the sounds of blasts.
- Move and store inventories of explosives, loaded perforating guns, and other materials, according to established safety procedures.
- Light fuses, drop detonating devices into wells or boreholes, or activate firing devices with plungers, dials, or buttons, in order to set off single or multiple blasts.
- Drive trucks to transport explosives and blasting equipment to blasting sites.
- Cut specified lengths of primacord and attach primers to cord ends.
- Maintain inventory levels, ordering new supplies as necessary.
- Repair and service blasting, shooting, and automotive equipment, and electrical wiring and instruments, using hand tools.
- Set up and operate short-wave radio or field telephone equipment to transmit and receive blast information.
- Clean, gauge, and lubricate gun ports.
- Connect gun chambers to electric detonating devices, and operate controls at panelboards, in order to detonate charges in guns or to ignite chemical charges.
- Obtain samples of earth from sidewalls of well boreholes, using electrically exploding devices.
- Create and lay out designs for drill and blast patterns.
- Document geological formations encountered during work.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Set up and operate equipment such as hoists, jackhammers, and drills, in order to bore charge holes.
- Signal crane operators to move equipment.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Insert waterproof sealers, bullets, and/or powder charges into guns, and screw gun ports back into place.
- Lower perforating guns into wells, using hoists; then use measuring devices and instrument panels to position guns in correct positions for taking samples.
- Insert powder charges into chambers of sidewall sample-taking cylinders, and assemble cylinders, using special wrenches.
- Place safety cones around blast areas to alert other workers of danger zones, and signal workers as necessary to ensure that they clear blast sites prior to explosions.
- Take actions to avoid potential hazards or obstructions, such as utility lines, other equipment, other workers, or falling objects.
- Coordinate machine actions with other activities, positioning or moving loads in response to hand or audio signals from crew members.
- Align machines, cutterheads, or depth gauge makers with reference stakes and guidelines or ground or position equipment, following hand signals of other workers.
- Learn and follow safety regulations.
- Start engines, move throttles, switches, or levers, or depress pedals to operate machines, such as bulldozers, trench excavators, road graders, or backhoes.
- Locate underground services, such as pipes or wires, prior to beginning work.
- Signal operators to guide movement of tractor-drawn machines.
- Repair and maintain equipment, making emergency adjustments or assisting with major repairs as necessary.
- Load and move dirt, rocks, equipment, or other materials, using trucks, crawler tractors, power cranes, shovels, graders, or related equipment.
- Drive and maneuver equipment equipped with blades in successive passes over working areas to remove topsoil, vegetation, or rocks or to distribute and level earth or terrain.
- Operate tractors or bulldozers to perform such tasks as clearing land, mixing sludge, trimming backfills, or building roadways or parking lots.
- Monitor operations to ensure that health and safety standards are met.
- Connect hydraulic hoses, belts, mechanical linkages, or power takeoff shafts to tractors.
- Select and fasten bulldozer blades or other attachments to tractors, using hitches.
- Operate loaders to pull out stumps, rip asphalt or concrete, rough-grade properties, bury refuse, or perform general cleanup.
- Operate equipment to demolish or remove debris or to remove snow from streets, roads, or parking lots.
- Keep records of material or equipment usage or problems encountered.
- Adjust handwheels and depress pedals to control attachments, such as blades, buckets, scrapers, or swing booms.
- Check fuel supplies at sites to ensure adequate availability.
- Perform specialized work, using equipment, such as pile drivers, dredging rigs, drillers, or concrete pumpers.
- Talk to clients and study instructions, plans, or diagrams to establish work requirements.
- Drive tractor-trailer trucks to move equipment from site to site.
- Push other equipment when extra traction or assistance is required.
- Operate road watering, oiling, or rolling equipment, or street sealing equipment, such as chip spreaders.
- Operate compactors, scrapers, or rollers to level, compact, or cover refuse at disposal grounds.
- Test atmosphere for adequate oxygen or explosive conditions when working in confined spaces.
- Compile cost estimates for jobs.
- Turn valves to control air or water output of compressors or pumps.
- Take actions to avoid potential hazards or obstructions, such as utility lines, other equipment, other workers, or falling objects.
- Coordinate machine actions with other activities, positioning or moving loads in response to hand or audio signals from crew members.
- Align machines, cutterheads, or depth gauge makers with reference stakes and guidelines or ground or position equipment, following hand signals of other workers.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Position and prepare truck-mounted derricks at drilling areas specified on field maps.
- Dig holes, set forms, and mix and pour concrete, for foundations of steel or wooden derricks.
- Train crews, and introduce procedures to make drill work more safe and effective.
- Observe pressure gauge and move throttles and levers to control the speed of rotary tables, and to regulate pressure of tools at bottoms of boreholes.
- Count sections of drill rod to determine depths of boreholes.
- Push levers and brake pedals to control gasoline, diesel, electric, or steam draw works that lower and raise drill pipes and casings in and out of wells.
- Connect sections of drill pipe, using hand tools and powered wrenches and tongs.
- Maintain records of footage drilled, location and nature of strata penetrated, materials and tools used, services rendered, and time required.
- Maintain and adjust machinery to ensure proper performance.
- Start and examine operation of slush pumps to ensure circulation and consistency of drilling fluid or mud in well.
- Locate and recover lost or broken bits, casings, and drill pipes from wells, using special tools.
- Weigh clay, and mix with water and chemicals to make drilling mud.
- Direct rig crews in drilling and other activities, such as setting up rigs and completing or servicing wells.
- Monitor progress of drilling operations, and select and change drill bits according to the nature of strata, using hand tools.
- Repair or replace defective parts of machinery, such as rotary drill rigs, water trucks, air compressors, and pumps, using hand tools.
- Clean and oil pulleys, blocks, and cables.
- Remove core samples during drilling to determine the nature of the strata being drilled.
- Cap wells with packers, or turn valves, to regulate outflow of oil from wells.
- Line drilled holes with pipes, and install all necessary hardware, to prepare new wells.
- Plug observation wells, and restore sites.
- Lower and explode charges in boreholes to start flow of oil from wells.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Position and prepare truck-mounted derricks at drilling areas specified on field maps.
- Dig holes, set forms, and mix and pour concrete, for foundations of steel or wooden derricks.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Dig or direct digging of post holes and set poles to support structures.
- Follow established safety rules and regulations and maintain a safe and clean environment.
- Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
- Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue.
- Study specifications in blueprints, sketches, or building plans to prepare project layout and determine dimensions and materials required.
- Shape or cut materials to specified measurements, using hand tools, machines, or power saws.
- Verify trueness of structure, using plumb bob and level.
- Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.
- Erect scaffolding or ladders for assembling structures above ground level.
- Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.
- Maintain records, document actions, and present written progress reports.
- Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.
- Maintain job records and schedule work crew.
- Bore boltholes in timber, masonry or concrete walls, using power drill.
- Install rough door and window frames, subflooring, fixtures, or temporary supports in structures undergoing construction or repair.
- Cover subfloors with building paper to keep out moisture and lay hardwood, parquet, or wood-strip-block floors by nailing floors to subfloor or cementing them to mastic or asphalt base.
- Construct forms or chutes for pouring concrete.
- Arrange for subcontractors to deal with special areas, such as heating or electrical wiring work.
- Build or repair cabinets, doors, frameworks, floors, or other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, or power tools.
- Finish surfaces of woodwork or wallboard in houses or buildings, using paint, hand tools, or paneling.
- Select and order lumber or other required materials.
- Work with or remove hazardous material.
- Fill cracks or other defects in plaster or plasterboard and sand patch, using patching plaster, trowel, and sanding tool.
- Prepare cost estimates for clients or employers.
- Perform minor plumbing, welding, or concrete mixing work.
- Apply shock-absorbing, sound-deadening, or decorative paneling to ceilings or walls.
- Examine structural timbers and supports to detect decay, and replace timbers as required, using hand tools, nuts, and bolts.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Dig or direct digging of post holes and set poles to support structures.
- Position bolting machines, and insert drill bits into chucks.
- Position safety jacks to support underground mine roofs until bolts can be installed.
- Drill bolt holes into roofs at specified distances from ribs or adjacent bolts.
- Pull down loose rock that cannot be supported.
- Perform safety checks on equipment before operating.
- Perform tests to determine if methane gas is present.
- Force bolts into holes, using hydraulic mechanisms of self-propelled bolting machines.
- Perform ventilation tasks, such as hanging ventilation curtains and tubes.
- Dust rocks after bolting.
- Install various types of bolts, including truss, glue, and resin bolts, traversing entire ceiling spans.
- Drill test holes and test bolts for specified tension, using torque wrenches.
- Rotate chucks to turn bolts and open expansion heads against rock formations.
- Remove drill bits from chucks after drilling holes, and insert bolts into chucks.
- Tighten ends of anchored truss bolts, using turnbuckles.
- Position bolting machines, and insert drill bits into chucks.
- Position safety jacks to support underground mine roofs until bolts can be installed.
- Reposition machines to make additional holes or cuts.
- Hang ventilation tubing and ventilation curtains to ensure that the mining face area is kept properly ventilated.
- Conduct methane gas checks to ensure breathing quality of air.
- Check the stability of roof and rib support systems before mining face areas.
- Operate mining machines to gather coal and convey it to floors or shuttle cars.
- Drive machines into position at working faces.
- Move controls to start and regulate movement of conveyors and to start and position drill cutters or torches.
- Determine locations, boundaries, and depths of holes or channels to be cut.
- Observe and listen to equipment operation to detect binding or stoppage of tools or other equipment malfunctions.
- Repair, oil, and adjust machines, and change cutting teeth, using wrenches.
- Install casings to prevent cave-ins.
- Scrape or wash conveyors, using belt scrapers or belt washers, to minimize dust production.
- Move levers to raise and lower hydraulic safety bars supporting roofs above machines until other workers complete framing.
- Apply new technologies developed to minimize the environmental impact of coal mining.
- Guide and assist crews laying track and resetting supports and blocking.
- Reposition machines to make additional holes or cuts.
- Hang ventilation tubing and ventilation curtains to ensure that the mining face area is kept properly ventilated.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Attach rigging and signal crane or hoist operators to lift heavy frame and plate sections or other parts into place.
- Study blueprints to determine locations, relationships, or dimensions of parts.
- Repair or replace defective pressure vessel parts, such as safety valves or regulators, using torches, jacks, caulking hammers, power saws, threading dies, welding equipment, or metalworking machinery.
- Locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments.
- Bolt or arc weld pressure vessel structures and parts together, using wrenches or welding equipment.
- Position, align, and secure structural parts or related assemblies to boiler frames, tanks, or vats of pressure vessels, following blueprints.
- Shape or fabricate parts, such as stacks, uptakes, or chutes, to adapt pressure vessels, heat exchangers, or piping to premises, using heavy-metalworking machines such as brakes, rolls, or drill presses.
- Lay out plate, sheet steel, or other heavy metal and locate and mark bending and cutting lines, using protractors, compasses, and drawing instruments or templates.
- Examine boilers, pressure vessels, tanks, or vats to locate defects, such as leaks, weak spots, or defective sections, so that they can be repaired.
- Shape seams, joints, or irregular edges of pressure vessel sections or structural parts to attain specified fit of parts, using cutting torches, hammers, files, or metalworking machines.
- Inspect assembled vessels or individual components, such as tubes, fittings, valves, controls, or auxiliary mechanisms, to locate any defects.
- Straighten or reshape bent pressure vessel plates or structure parts, using hammers, jacks, or torches.
- Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.
- Clean pressure vessel equipment, using scrapers, wire brushes, and cleaning solvents.
- Bell, bead with power hammers, or weld pressure vessel tube ends to ensure leakproof joints.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Position and align derrick elements, using harnesses and platform climbing devices.
- Inspect derricks, or order their inspection, prior to being raised or lowered.
- Inspect derricks for flaws, and clean and oil derricks to maintain proper working conditions.
- Control the viscosity and weight of the drilling fluid.
- Repair pumps, mud tanks, and related equipment.
- Set and bolt crown blocks to posts at tops of derricks.
- Listen to mud pumps and check regularly for vibration and other problems to ensure that rig pumps and drilling mud systems are working properly.
- Start pumps that circulate mud through drill pipes and boreholes to cool drill bits and flush out drill cuttings.
- Supervise crew members, and provide assistance in training them.
- Guide lengths of pipe into and out of elevators.
- Prepare mud reports, and instruct crews about the handling of any chemical additives.
- Clamp holding fixtures on ends of hoisting cables.
- Weigh clay, and mix with water and chemicals to make drilling mud, using portable mixers.
- String cables through pulleys and blocks.
- Steady pipes during connection to or disconnection from drill or casing strings.
- Position and align derrick elements, using harnesses and platform climbing devices.
- Install gas burners to convert furnaces from wood, coal, or oil.
- Measure, cut, thread and assemble new pipe, placing the assembled pipe in hangers or other supports.
- Cut or drill holes in walls or floors to accommodate the passage of pipes.
- Perform rough-ins, repair and replace fixtures and water heaters, and locate, repair, or remove leaking or broken pipes.
- Assist pipe fitters in the layout, assembly, and installation of piping for air, ammonia, gas, and water systems.
- Cut pipe and lift up to fitters.
- Fit or assist in fitting valves, couplings, or assemblies to tanks, pumps, or systems, using hand tools.
- Requisition tools and equipment, select type and size of pipe, and collect and transport materials and equipment to work site.
- Mount brackets and hangers on walls and ceilings to hold pipes, and set sleeves or inserts to provide support for pipes.
- Excavate and grade ditches, and lay and join pipe for water and sewer service.
- Disassemble and remove damaged or worn pipe.
- Clean shop, work area, and machines, using solvent and rags.
- Fill pipes with sand or resin to prevent distortion, and hold pipes during bending and installation.
- Immerse pipe in chemical solution to remove dirt, oil, and scale.
- Clean and renew steam traps.
- Install gas burners to convert furnaces from wood, coal, or oil.
- Bolt together pump and engine parts.
- Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.
- Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.
- Guide cranes to move loads about decks.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Lay gas and oil pipelines.
- Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.
- Clean trucks used in the fields.
- Bolt or nail together wood or steel framework to erect derricks.
- Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.
- Supply equipment to rig floors as requested and provide assistance to roughnecks.
- Clean up spilled oil by bailing it into barrels.
- Keep pipe deck and main deck areas clean and tidy.
- Dig drainage ditches around wells and storage tanks.
- Cut down and remove trees and brush to clear drill sites, to reduce fire hazards, and to make way for roads to sites.
- Bolt together pump and engine parts.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Maintain equipment, making repairs or modifications when necessary.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Transport prefabricated parts to construction sites for assembly and installation.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Hire, train, or supervise new employees or apprentices.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Fabricate or alter parts at construction sites, using shears, hammers, punches, or drills.
- Determine project requirements, such as scope, assembly sequences, or required methods or materials, using blueprints, drawings, or written or verbal instructions.
- Maneuver completed roofing units into position for installation.
- Select gauges or types of sheet metal or nonmetallic material, according to product specifications.
- Shape metal material over anvils, blocks, or other forms, using hand tools.
- Trim, file, grind, deburr, buff, or smooth surfaces, seams, or joints of assembled parts, using hand tools or portable power tools.
- Inspect individual parts, assemblies, or installations, using measuring instruments, such as calipers, scales, or micrometers.
- Develop or lay out patterns, using computerized metalworking equipment.
- Convert blueprints into shop drawings to be followed in the construction or assembly of sheet metal products.
- Perform sheet metal work necessary for solar panel installations.
- Verify that heating, ventilating, and air conditioning (HVAC) systems are designed, installed, and calibrated in accordance with green certification standards, such as those of Leadership in Energy and Environmental Design (LEED).
- Secure metal roof panels in place by interlocking and fastening grooved panel edges.
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Finish parts, using hacksaws or hand, rotary, or squaring shears.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Raise, lower, or position equipment, tools, and materials, using hoist, hand line, or block and tackle.
- Strip insulation from wire ends, using wire stripping pliers, and attach wires to terminals for subsequent soldering.
- Trace out short circuits in wiring, using test meter.
- Measure, cut, and bend wire and conduit, using measuring instruments and hand tools.
- Examine electrical units for loose connections and broken insulation and tighten connections, using hand tools.
- Maintain tools, vehicles, and equipment and keep parts and supplies in order.
- Drill holes and pull or push wiring through openings, using hand and power tools.
- Clean work area and wash parts.
- Perform semi-skilled and unskilled laboring duties related to the installation, maintenance and repair of a wide variety of electrical systems and equipment.
- Thread conduit ends, connect couplings, and fabricate and secure conduit support brackets, using hand tools.
- Disassemble defective electrical equipment, replace defective or worn parts, and reassemble equipment, using hand tools.
- Construct controllers and panels, using power drills, drill presses, taps, saws, and punches.
- Transport tools, materials, equipment, and supplies to work site by hand, handtruck, or heavy, motorized truck.
- String transmission lines or cables through ducts or conduits, under the ground, through equipment, or to towers.
- Install copper-clad ground rods, using a manual post driver.
- Dig trenches or holes for installation of conduit or supports.
- Bolt component parts together to form tower assemblies, using hand tools.
- Erect electrical system components and barricades, and rig scaffolds, hoists, and shoring.
- Trim trees and clear undergrowth along right-of-way.
- Requisition materials, using warehouse requisition or release forms.
- Solder electrical connections, using soldering iron.
- Paint a variety of objects related to electrical functions.
- Break up concrete, using airhammer, to facilitate installation, construction, or repair of equipment.
- Operate heavy equipment, such as backhoes.
- Operate cutting torches and welding equipment, while working with conduit and metal components to construct devices associated with electrical functions.
- Raise, lower, or position equipment, tools, and materials, using hoist, hand line, or block and tackle.
