Job Duties Custom List 47-2181.00 — Roofers
- Install vapor barriers or layers of insulation on flat roofs.
Occupations with related tasks Save Table: XLSX CSV
- Fit, wrap, staple, or glue insulating materials to structures or surfaces, using hand tools or wires.
- Cover and line structures with blown or rolled forms of materials to insulate against cold, heat, or moisture, using saws, knives, rasps, trowels, blowers, or other tools and implements.
- Distribute insulating materials evenly into small spaces within floors, ceilings, or walls, using blowers and hose attachments, or cement mortars.
- Move controls, buttons, or levers to start blowers and regulate flow of materials through nozzles.
- Cover, seal, or finish insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement or asphalt mastic.
- Measure and cut insulation for covering surfaces, using tape measures, handsaws, power saws, knives, or scissors.
- Fill blower hoppers with insulating materials.
- Read blueprints, and select appropriate insulation, based on space characteristics and the heat retaining or excluding characteristics of the material.
- Remove old insulation, such as asbestos, following safety procedures.
- Prepare surfaces for insulation application by brushing or spreading on adhesives, cement, or asphalt, or by attaching metal pins to surfaces.
- Fit, wrap, staple, or glue insulating materials to structures or surfaces, using hand tools or wires.
- Cover and line structures with blown or rolled forms of materials to insulate against cold, heat, or moisture, using saws, knives, rasps, trowels, blowers, or other tools and implements.
- Distribute insulating materials evenly into small spaces within floors, ceilings, or walls, using blowers and hose attachments, or cement mortars.
- Move controls, buttons, or levers to start blowers and regulate flow of materials through nozzles.
- Cover, seal, or finish insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement or asphalt mastic.
- Apply insulation materials, such as loose, blanket, board, and foam insulation to attics, crawl spaces, basements, or walls.
- Wrap air ducts and water lines with insulating materials, such as duct wrap and pipe insulation.
- Prepare and apply weather-stripping, glazing, caulking, or door sweeps to reduce energy losses.
- Wrap water heaters with water heater blankets.
- Install and seal air ducts, combustion air openings, or ventilation openings to improve heating and cooling efficiency.
- Make minor repairs using basic hand or power tools and materials, such as glass, lumber, and drywall.
- Install storm windows or storm doors and verify proper fit.
- Test combustible appliances, such as gas appliances.
- Determine amount of air leakage in buildings, using a blower door machine.
- Test and diagnose air flow systems, using furnace efficiency analysis equipment.
- Inspect buildings to identify required weatherization measures, including repair work, modification, or replacement.
- Recommend weatherization techniques to clients in accordance with needs and applicable energy regulations, codes, policies, or statutes.
- Prepare cost estimates or specifications for rehabilitation or weatherization services.
- Contact residents or building owners to schedule appointments.
- Clean and maintain tools and equipment.
- Apply spackling, compounding, or other materials to repair holes in walls.
- Explain recommendations, policies, procedures, requirements, or other related information to residents or building owners.
- Maintain activity logs, financial transaction logs, or other records of weatherization work performed.
- Explain energy conservation measures, such as the use of low flow showerheads and energy-efficient lighting.
- Prepare or assist in the preparation of bids, contracts, or written reports related to weatherization work.
- Apply insulation materials, such as loose, blanket, board, and foam insulation to attics, crawl spaces, basements, or walls.
- Wrap air ducts and water lines with insulating materials, such as duct wrap and pipe insulation.
- Prepare and apply weather-stripping, glazing, caulking, or door sweeps to reduce energy losses.
- Wrap water heaters with water heater blankets.
- Install and seal air ducts, combustion air openings, or ventilation openings to improve heating and cooling efficiency.
- Make minor repairs using basic hand or power tools and materials, such as glass, lumber, and drywall.
- Install storm windows or storm doors and verify proper fit.
- Apply, remove, and repair insulation on industrial equipment, pipes, ductwork, or other mechanical systems such as heat exchangers, tanks, and vessels, to help control noise and maintain temperatures.
- Fit insulation around obstructions, and shape insulating materials and protective coverings as required.
- Cover, seal, or finish insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement, or asphalt mastic.
- Install sheet metal around insulated pipes with screws to protect the insulation from weather conditions or physical damage.
- Measure and cut insulation for covering surfaces, using tape measures, handsaws, knives, and scissors.
- Select appropriate insulation, such as fiberglass, Styrofoam, or cork, based on the heat retaining or excluding characteristics of the material.
- Determine the amounts and types of insulation needed, and methods of installation, based on factors such as location, surface shape, and equipment use.
- Read blueprints and specifications to determine job requirements.
- Prepare surfaces for insulation application by brushing or spreading on adhesives, cement, or asphalt, or by attaching metal pins to surfaces.
- Apply, remove, and repair insulation on industrial equipment, pipes, ductwork, or other mechanical systems such as heat exchangers, tanks, and vessels, to help control noise and maintain temperatures.
- Fit insulation around obstructions, and shape insulating materials and protective coverings as required.
- Cover, seal, or finish insulated surfaces or access holes with plastic covers, canvas strips, sealants, tape, cement, or asphalt mastic.
- Install sheet metal around insulated pipes with screws to protect the insulation from weather conditions or physical damage.
- Install blanket insulation between studs and tack plastic moisture barriers over insulation.
- Fit and fasten wallboard or drywall into position on wood or metal frameworks, using glue, nails, or screws.
- Assemble or install metal framing or decorative trim for windows, doorways, or vents.
- Cut fixture or border tiles to size, using keyhole saws, and insert them into surrounding frameworks.
- Cut and screw together metal channels to make floor or ceiling frames, according to plans for the location of rooms or hallways.
- Hang drywall panels on metal frameworks of walls and ceilings in offices, schools, or other large buildings, using lifts or hoists to adjust panel heights, when necessary.
- Suspend angle iron grids or channel irons from ceilings, using wire.
- Install horizontal and vertical metal or wooden studs to frames so that wallboard can be attached to interior walls.
- Fasten metal or rockboard lath to the structural framework of walls, ceilings, or partitions of buildings, using nails, screws, staples, or wire-ties.
- Apply or mount acoustical tile or blocks, strips, or sheets of shock-absorbing materials to ceilings or walls of buildings to reduce reflection of sound or to decorate rooms.
- Mount tile, using adhesives, or by nailing, screwing, stapling, or wire-tying lath directly to structural frameworks.
- Nail channels or wood furring strips to surfaces to provide mounting for tile.
- Install metal lath where plaster applications will be exposed to weather or water, or for curved or irregular surfaces.
- Apply cement to backs of tiles and press tiles into place, aligning them with layout marks or joints of previously laid tile.
- Read blueprints or other specifications to determine methods of installation, work procedures, or material or tool requirements.
- Measure and mark surfaces to lay out work, according to blueprints or drawings, using tape measures, straightedges or squares, and marking devices.
- Measure and cut openings in panels or tiles for electrical outlets, windows, vents, plumbing, or other fixtures, using keyhole saws or other cutting tools.
- Cut metal or wood framing and trim to size, using cutting tools.
- Inspect furrings, mechanical mountings, or masonry surfaces for plumbness and level, using spirit or water levels.
- Trim rough edges from wallboard to maintain even joints, using knives.
- Coordinate work with drywall finishers who cover the seams between drywall panels.
- Scribe and cut edges of tile to fit walls where wall molding is not specified.
- Hang dry lines to wall moldings to guide positioning of main runners.
- Seal joints between ceiling tiles and walls.
- Remove existing plaster, drywall, or paneling, using crowbars and hammers.
- Wash concrete surfaces before mounting tile to increase adhesive qualities of surfaces, using washing soda and zinc sulfate solution.
- Install blanket insulation between studs and tack plastic moisture barriers over insulation.
- Fit and fasten wallboard or drywall into position on wood or metal frameworks, using glue, nails, or screws.
- Assemble or install metal framing or decorative trim for windows, doorways, or vents.
- Cut fixture or border tiles to size, using keyhole saws, and insert them into surrounding frameworks.
- Cut and screw together metal channels to make floor or ceiling frames, according to plans for the location of rooms or hallways.
- Hang drywall panels on metal frameworks of walls and ceilings in offices, schools, or other large buildings, using lifts or hoists to adjust panel heights, when necessary.
- Suspend angle iron grids or channel irons from ceilings, using wire.
- Install horizontal and vertical metal or wooden studs to frames so that wallboard can be attached to interior walls.
- Fasten metal or rockboard lath to the structural framework of walls, ceilings, or partitions of buildings, using nails, screws, staples, or wire-ties.
- Apply or mount acoustical tile or blocks, strips, or sheets of shock-absorbing materials to ceilings or walls of buildings to reduce reflection of sound or to decorate rooms.
- Mount tile, using adhesives, or by nailing, screwing, stapling, or wire-tying lath directly to structural frameworks.
- Nail channels or wood furring strips to surfaces to provide mounting for tile.
- Install metal lath where plaster applications will be exposed to weather or water, or for curved or irregular surfaces.
- Apply cement to backs of tiles and press tiles into place, aligning them with layout marks or joints of previously laid tile.
- Insert sealing strips, wiring, insulating material, ladders, flanges, gauges, or valves, depending on types of structures being assembled.
- Connect columns, beams, and girders with bolts, following blueprints and instructions from supervisors.
- Bolt aligned structural steel members in position for permanent riveting, bolting, or welding into place.
- Erect metal or precast concrete components for structures, such as buildings, bridges, dams, towers, storage tanks, fences, or highway guard rails.
- Force structural steel members into final positions, using turnbuckles, crowbars, jacks, or hand tools.
- Drive drift pins through rivet holes to align rivet holes in structural steel members with corresponding holes in previously placed members.
- Assemble hoisting equipment or rigging, such as cables, pulleys, or hooks, to move heavy equipment or materials.
- Read specifications or blueprints to determine the locations, quantities, or sizes of materials required.
- Fasten structural steel members to hoist cables, using chains, cables, or rope.
- Hoist steel beams, girders, or columns into place, using cranes or signaling hoisting equipment operators to lift and position structural steel members.
- Verify vertical and horizontal alignment of structural steel members, using plumb bobs, laser equipment, transits, or levels.
- Cut, bend, or weld steel pieces, using metal shears, torches, or welding equipment.
- Pull, push, or pry structural steel members into approximate positions for bolting into place.
- Unload and position prefabricated steel units for hoisting, as needed.
- Fabricate metal parts, such as steel frames, columns, beams, or girders, according to blueprints or instructions from supervisors.
- Dismantle structures or equipment.
- Ride on girders or other structural steel members to position them, or use rope to guide them into position.
- Hold rivets while riveters use air hammers to form heads on rivets.
- Place blocks under reinforcing bars used to reinforce floors.
- Insert sealing strips, wiring, insulating material, ladders, flanges, gauges, or valves, depending on types of structures being assembled.
- Connect columns, beams, and girders with bolts, following blueprints and instructions from supervisors.
- Bolt aligned structural steel members in position for permanent riveting, bolting, or welding into place.
- Erect metal or precast concrete components for structures, such as buildings, bridges, dams, towers, storage tanks, fences, or highway guard rails.
- Force structural steel members into final positions, using turnbuckles, crowbars, jacks, or hand tools.
- Drive drift pins through rivet holes to align rivet holes in structural steel members with corresponding holes in previously placed members.
- Assemble hoisting equipment or rigging, such as cables, pulleys, or hooks, to move heavy equipment or materials.
- Cut and install insulating or sound-absorbing material.
- Fasten timbers or lumber with glue, screws, pegs, or nails and install hardware.
- Erect scaffolding, shoring, or braces.
- Install handrails under the direction of a carpenter.
- Clean work areas, machines, or equipment, to maintain a clean and safe job site.
- Perform tie spacing layout and measure, mark, drill or cut.
- Select tools, equipment, or materials from storage and transport items to work site.
- Drill holes in timbers or lumber.
- Cut timbers, lumber, or paneling to specified dimensions.
- Position and hold timbers, lumber, or paneling in place for fastening or cutting.
- Align, straighten, plumb, or square forms for installation.
- Hold plumb bobs, sighting rods, or other equipment to aid in establishing reference points and lines.
- Construct forms and assist in raising them to the required elevation.
- Glue and clamp edges or joints of assembled parts.
- Smooth or sand surfaces to remove ridges, tool marks, glue, or caulking.
- Secure stakes to grids for constructions of footings, nail scabs to footing forms, and vibrate and float concrete.
- Cut tile or linoleum to fit and spread adhesives on flooring for installation.
- Cover surfaces with laminated plastic covering material.
- Cut or weld metal.
- Cut and install insulating or sound-absorbing material.
- Fasten timbers or lumber with glue, screws, pegs, or nails and install hardware.
- Erect scaffolding, shoring, or braces.
- Install handrails under the direction of a carpenter.
- Apply insulation to building exteriors by installing prefabricated insulation systems over existing walls or by covering the outer wall with insulation board, reinforcing mesh, and a base coat.
- Set up scaffolds.
- Mold or install ornamental plaster pieces, panels, or trim.
- Cover surfaces such as windows, doors, or sidewalks to protect from splashing.
- Clean job sites.
- Mix mortar and plaster to desired consistency or direct workers who perform mixing.
- Apply coats of plaster or stucco to walls, ceilings, or partitions of buildings, using trowels, brushes, or spray guns.
- Determine materials needed to complete the job and place orders accordingly.
- Apply weatherproof, decorative coverings to exterior surfaces of buildings, such as by troweling or spraying on coats of stucco.
- Clean and prepare surfaces for applications of plaster, cement, stucco, or similar materials, such as by drywall taping.
- Create decorative textures in finish coat, using brushes or trowels, sand, pebbles, or stones.
- Rough the undercoat surface with a scratcher so the finish coat will adhere.
- Cure freshly plastered surfaces.
- Install guide wires on exterior surfaces of buildings to indicate thickness of plaster or stucco and nail wire mesh, lath, or similar materials to the outside surface to hold stucco in place.
- Spray acoustic materials or texture finish over walls or ceilings.
- Apply insulation to building exteriors by installing prefabricated insulation systems over existing walls or by covering the outer wall with insulation board, reinforcing mesh, and a base coat.
- Set up scaffolds.
- Mold or install ornamental plaster pieces, panels, or trim.
- Position, attach, or blow insulating materials to prevent energy losses from buildings, pipes, or other structures or objects.
- Fabricate or repair counters, benches, partitions, or other wooden structures, such as sheds or outbuildings.
- Perform routine maintenance, such as inspecting drives, motors, or belts, checking fluid levels, replacing filters, or doing other preventive maintenance actions.
- Inspect, operate, or test machinery or equipment to diagnose machine malfunctions.
- Adjust functional parts of devices or control instruments, using hand tools, levels, plumb bobs, or straightedges.
- Repair machines, equipment, or structures, using tools such as hammers, hoists, saws, drills, wrenches, or equipment such as precision measuring instruments or electrical or electronic testing devices.
- Order parts, supplies, or equipment from catalogs or suppliers.
- Diagnose mechanical problems and determine how to correct them, checking blueprints, repair manuals, or parts catalogs, as necessary.
- Design new equipment to aid in the repair or maintenance of machines, mechanical equipment, or building structures.
- Assemble, install, or repair wiring, electrical or electronic components, pipe systems, plumbing, machinery, or equipment.
- Clean or lubricate shafts, bearings, gears, or other parts of machinery.
- Estimate costs to repair machinery, equipment, or building structures.
- Align and balance new equipment after installation.
- Record type and cost of maintenance or repair work.
- Maintain or repair specialized equipment or machinery located in cafeterias, laundries, hospitals, stores, offices, or factories.
- Dismantle machines, equipment, or devices to access and remove defective parts, using hoists, cranes, hand tools, or power tools.
- Plan and lay out repair work, using diagrams, drawings, blueprints, maintenance manuals, or schematic diagrams.
- Install equipment to improve the energy or operational efficiency of residential or commercial buildings.
- Set up and operate machine tools to repair or fabricate machine parts, jigs, fixtures, or tools.
- Perform general cleaning of buildings or properties.
- Train or manage maintenance personnel or subcontractors.
- Paint or repair roofs, windows, doors, floors, woodwork, plaster, drywall, or other parts of building structures.
- Perform routine maintenance on boilers, such as replacing burners or hoses, installing replacement parts, or reinforcing structural weaknesses to ensure optimal boiler efficiency.
- Provide groundskeeping services, such as landscaping or snow removal.
- Operate cutting torches or welding equipment to cut or join metal parts.
- Inspect used parts to determine changes in dimensional requirements, using rules, calipers, micrometers, or other measuring instruments.
- Assemble boilers at installation sites, using tools such as levels, plumb bobs, hammers, torches, or other hand tools.
- Use drones for inspecting roofs, gutters, and other hard-to-reach areas of buildings.
- Position, attach, or blow insulating materials to prevent energy losses from buildings, pipes, or other structures or objects.
- Fabricate or repair counters, benches, partitions, or other wooden structures, such as sheds or outbuildings.
- Remove seats, carpeting, and interiors of doors and add sound-absorbing material in empty spaces, reinstalling interior parts.
- Install equipment and accessories, such as stereos, navigation equipment, communication equipment, and security systems.
- Inspect and test electrical or electronic systems to locate and diagnose malfunctions, using visual inspections and testing instruments, such as oscilloscopes and voltmeters.
- Cut openings and drill holes for fixtures and equipment, using electric drills and routers.
- Splice wires with knives or cutting pliers, and solder connections to fixtures and equipment.
- Diagnose or repair problems with electronic equipment, such as sound, navigation, communication, and security equipment, in motor vehicles.
- Run new speaker and electrical cables.
- Confer with customers to determine the nature of malfunctions.
- Record results of diagnostic tests.
- Estimate costs of repairs, based on parts and labor charges.
- Replace and clean electrical or electronic components.
- Build fiberglass or wooden enclosures for sound components, and fit them to automobile dimensions.
- Remove seats, carpeting, and interiors of doors and add sound-absorbing material in empty spaces, reinstalling interior parts.
- Place insulation over conductors, or seal splices with moisture-proof covering.
- Set up service for customers, installing, connecting, testing, or adjusting equipment.
- Travel to customers' premises to install, maintain, or repair audio and visual electronic reception equipment or accessories.
- Measure signal strength at utility poles, using electronic test equipment.
- Inspect or test lines or cables, recording and analyzing test results, to assess transmission characteristics and locate faults or malfunctions.
- Splice cables, using hand tools, epoxy, or mechanical equipment.
- Access specific areas to string lines, or install terminal boxes, auxiliary equipment, or appliances, using bucket trucks, climbing poles or ladders, or entering tunnels, trenches, or crawl spaces.
- Clean or maintain tools or test equipment.
- String cables between structures and lines from poles, towers, or trenches, and pull lines to proper tension.
- Pull up cable by hand from large reels mounted on trucks.
- Lay underground cable directly in trenches, or string it through conduits running through trenches.
- Pull cable through ducts by hand or with winches.
- Dig trenches for underground wires or cables.
- Explain cable service to subscribers after installation, and collect any installation fees due.
- Compute impedance of wires from poles to houses to determine additional resistance needed for reducing signals to desired levels.
- Install equipment such as amplifiers or repeaters to maintain the strength of communications transmissions.
- Use a variety of construction equipment to complete installations, such as digger derricks, trenchers, or cable plows.
- Fill and tamp holes, using cement, earth, and tamping devices.
- Dig holes for power poles, using power augers or shovels, set poles in place with cranes, and hoist poles upright, using winches.
- Place insulation over conductors, or seal splices with moisture-proof covering.
- Cut, miter, and glue piping insulation to insulate plumbing pipes and fittings.
- Test operation or functionality of mechanical, plumbing, electrical, and control systems.
- Apply weather seal, such as pipe flashings and sealants, to roof penetrations and structural devices.
- Install solar collector mounting devices on tile, asphalt, shingle, or built-up gravel roofs, using appropriate materials and penetration methods.
- Install copper or plastic plumbing using pipes, fittings, pipe cutters, acetylene torches, solder, wire brushes, sand cloths, flux, plastic pipe cleaners, or plastic glue.
- Identify plumbing, electrical, environmental, or safety hazards associated with solar thermal installations.
- Demonstrate start-up, shut-down, maintenance, diagnostic, and safety procedures to thermal system owners.
- Install circulating pumps using pipe, fittings, soldering equipment, electrical supplies, and hand tools.
- Install flat-plat, evacuated glass, or concentrating solar collectors on mounting devices, using brackets or struts.
- Install solar thermal system controllers and sensors.
- Fill water tanks and check tanks, pipes, and fittings for leaks.
- Design active direct or indirect, passive direct or indirect, or pool solar systems.
- Determine locations for installing solar subsystem components, including piping, water heaters, valves, and ancillary equipment.
- Perform routine maintenance or repairs to restore solar thermal systems to baseline operating conditions.
- Install heat exchangers and heat exchanger fluids according to installation manuals and schematics.
- Apply operation or identification tags or labels to system components, as required.
- Connect water heaters and storage tanks to power and water sources.
- Install plumbing, such as dip tubes, port fittings, drain tank valves, pressure temperature relief valves, or tanks, according to manufacturer specifications and building codes.
- Install monitoring system components, such as flow meters, temperature gauges, and pressure gauges, according to system design and manufacturer specifications.
- Assess collector sites to ensure structural integrity of potential mounting surfaces or the best orientation and tilt for solar collectors.
- Apply ultraviolet radiation protection to prevent degradation of plumbing.
- Cut, miter, and glue piping insulation to insulate plumbing pipes and fittings.
- Place insulating or fireproofing materials over conductors and joints.
- Adhere to safety practices and procedures, such as checking equipment regularly and erecting barriers around work areas.
- Drive vehicles equipped with tools and materials to job sites.
- Open switches or attach grounding devices to remove electrical hazards from disturbed or fallen lines or to facilitate repairs.
- Climb poles or use truck-mounted buckets to access equipment.
- Install, maintain, and repair electrical distribution and transmission systems, including conduits, cables, wires, and related equipment, such as transformers, circuit breakers, and switches.
- Inspect and test power lines and auxiliary equipment to locate and identify problems, using reading and testing instruments.
- Coordinate work assignment preparation and completion with other workers.
- Replace or straighten damaged poles.
- String wire conductors and cables between poles, towers, trenches, pylons, and buildings, setting lines in place and using winches to adjust tension.
- Attach cross-arms, insulators, and auxiliary equipment to poles prior to installing them.
- Dig holes, using augers, and set poles, using cranes and power equipment.
- Travel in trucks, helicopters, and airplanes to inspect lines for freedom from obstruction and adequacy of insulation.
- Identify defective sectionalizing devices, circuit breakers, fuses, voltage regulators, transformers, switches, relays, or wiring, using wiring diagrams and electrical-testing instruments.
- Install watt-hour meters and connect service drops between power lines and consumers' facilities.
- Test conductors, according to electrical diagrams and specifications, to identify corresponding conductors and to prevent incorrect connections.
- Splice or solder cables together or to overhead transmission lines, customer service lines, or street light lines, using hand tools, epoxies, or specialized equipment.
- Trim trees that could be hazardous to the functioning of cables or wires.
- Pull up cable by hand from large reels mounted on trucks.
- Lay underground cable directly in trenches, or string it through conduit running through the trenches.
- Cut trenches for laying underground cables, using trenchers and cable plows.
- Cut and peel lead sheathing and insulation from defective or newly installed cables and conduits prior to splicing.
- Clean, tin, and splice corresponding conductors by twisting ends together or by joining ends with metal clamps and soldering connections.
- Place insulating or fireproofing materials over conductors and joints.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Lift units or parts such as motors or generators, using cranes or chain hoists, or signal crane operators to lift heavy parts or subassemblies.
- Record repairs required, parts used, and labor time.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Lubricate moving parts.
- Read service guides to find information needed to perform repairs.
- Inspect electrical connections, wiring, relays, charging resistance boxes, and storage batteries, following wiring diagrams.
- Scrape and clean units or parts, using cleaning solvents and equipment such as buffing wheels.
- Weld, braze, or solder electrical connections.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Steam-clean polishing and buffing wheels to remove abrasives and bonding materials, and spray, brush, or recoat surfaces as necessary.
- Set machinery for proper performance, using computers.
- Test equipment for overheating, using speed gauges and thermometers.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Maintain stocks of parts.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Solder, wrap, and coat wires to ensure proper insulation.
- Rewire electrical systems, and repair or replace electrical accessories.
- Clean cells, cell assemblies, glassware, leads, electrical connections, and battery poles, using scrapers, steam, water, emery cloths, power grinders, or acid.
- Rewind coils on cores in slots, or make replacement coils, using coil-winding machines.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Hammer out dents and twists in tools and equipment.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Repair and operate battery-charging equipment.
- Sharpen tools such as saws, picks, shovels, screwdrivers, and scoops, either manually or by using bench grinders and emery wheels.
- Test battery charges, and replace or recharge batteries as necessary.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
