Job Duties Custom List 47-2181.00 — Roofers
- Apply reflective roof coatings, such as special paints or single-ply roofing sheets, to existing roofs to reduce solar heat absorption.
Occupations with related tasks Save Table: XLSX CSV
- Cover roofs with layers of roofing felt or asphalt strips before installing tile, slate, or composition materials.
- Place tiles, nail them to roof boards, and cover nailheads with roofing cement.
- Attach roofing paper and composition shingles, using nails.
- Perform emergency leak repairs and general maintenance for a variety of roof types.
- Attach sheets of metal to roof boards or building frameworks when installing metal roofs.
- Apply shingles, gravel, or asphalt over the top layer of tar to protect the roofing material.
- Set ladders, scaffolds, and hoists in place for taking supplies to roofs.
- Check to ensure that completed roofs are watertight.
- Sweep and clean roofs to prepare them for the application of new roofing materials.
- Locate worn or torn areas in roofs.
- Clean work areas and equipment.
- Maintain tools and equipment.
- Remove old roofing materials.
- Unload materials and tools from work trucks, and unroll roofing as directed.
- Provide assistance to skilled roofers installing and repairing roofs, flashings, and surfaces.
- Hoist tar and roofing materials to roofs, using ropes and pulleys, or carry materials up ladders.
- Chop tar into small pieces, and heat chopped tar in kettles.
- Clear drains and downspouts and clean gutters.
- Cover roofs with layers of roofing felt or asphalt strips before installing tile, slate, or composition materials.
- Place tiles, nail them to roof boards, and cover nailheads with roofing cement.
- Attach roofing paper and composition shingles, using nails.
- Perform emergency leak repairs and general maintenance for a variety of roof types.
- Attach sheets of metal to roof boards or building frameworks when installing metal roofs.
- Apply shingles, gravel, or asphalt over the top layer of tar to protect the roofing material.
- Set ladders, scaffolds, and hoists in place for taking supplies to roofs.
- Spray materials, such as water, sand, steam, vinyl, paint, or stucco, through hoses to clean, coat, or seal surfaces.
- Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.
- Perform site activities required of green certified construction practices, such as implementing waste management procedures, identifying materials for reuse, or installing erosion or sedimentation control mechanisms.
- Erect or dismantle scaffolding, shoring, braces, traffic barricades, ramps, or other temporary structures.
- Perform building weatherization tasks, such as repairing windows, adding insulation, or applying weather-stripping materials.
- Apply weather-stripping to reduce energy loss.
- Place, consolidate, or protect case-in-place concrete or masonry structures.
- Apply caulking compounds by hand or caulking guns to protect against entry of water or air.
- Perform construction laborer duties at green building sites, such as renewable energy plants or wind turbine installations.
- Tend pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.
- Lubricate, clean, or repair machinery, equipment, or tools.
- Signal equipment operators to facilitate alignment, movement, or adjustment of machinery, equipment, or materials.
- Read plans, instructions, or specifications to determine work activities.
- Measure, mark, or record openings or distances to layout areas where construction work will be performed.
- Clean or prepare construction sites to eliminate possible hazards.
- Dig ditches or trenches, backfill excavations, or compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, or rakes.
- Load, unload, or identify building materials, machinery, or tools, distributing them to the appropriate locations, according to project plans or specifications.
- Position, join, align, or seal structural components, such as concrete wall sections or pipes.
- Control traffic passing near, in, or around work zones.
- Install sewer, water, or storm drain pipes, using pipe-laying machinery or laser guidance equipment.
- Operate or maintain air monitoring or other sampling devices in confined or hazardous environments.
- Smooth or finish freshly poured cement or concrete, using floats, trowels, screeds, or powered cement finishing tools.
- Provide assistance to craft workers, such as carpenters, plasterers, or masons.
- Raze buildings or salvage useful materials.
- Position or dismantle forms for pouring concrete, using saws, hammers, nails, or bolts.
- Grind, scrape, sand, or polish surfaces, such as concrete, marble, terrazzo, or wood flooring, using abrasive tools or machines.
- Mix ingredients to create compounds for covering or cleaning surfaces.
- Mix, pour, or spread concrete, using portable cement mixers.
- Operate jackhammers or drills to break up concrete or pavement.
- Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings or walls.
- Identify, pack, or transport hazardous or radioactive materials.
- Use computers or other input devices to control robotic pipe cutters or cleaners.
- Spray materials, such as water, sand, steam, vinyl, paint, or stucco, through hoses to clean, coat, or seal surfaces.
- Mop, brush, or spread paints, cleaning solutions, or other compounds over surfaces to clean them or to provide protection.
- Perform site activities required of green certified construction practices, such as implementing waste management procedures, identifying materials for reuse, or installing erosion or sedimentation control mechanisms.
- Erect or dismantle scaffolding, shoring, braces, traffic barricades, ramps, or other temporary structures.
- Perform building weatherization tasks, such as repairing windows, adding insulation, or applying weather-stripping materials.
- Apply weather-stripping to reduce energy loss.
- Place, consolidate, or protect case-in-place concrete or masonry structures.
- Apply caulking compounds by hand or caulking guns to protect against entry of water or air.
- Perform construction laborer duties at green building sites, such as renewable energy plants or wind turbine installations.
- Secure metal roof panels in place by interlocking and fastening grooved panel edges.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Maintain equipment, making repairs or modifications when necessary.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Transport prefabricated parts to construction sites for assembly and installation.
- Hire, train, or supervise new employees or apprentices.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Fabricate or alter parts at construction sites, using shears, hammers, punches, or drills.
- Determine project requirements, such as scope, assembly sequences, or required methods or materials, using blueprints, drawings, or written or verbal instructions.
- Maneuver completed roofing units into position for installation.
- Select gauges or types of sheet metal or nonmetallic material, according to product specifications.
- Shape metal material over anvils, blocks, or other forms, using hand tools.
- Trim, file, grind, deburr, buff, or smooth surfaces, seams, or joints of assembled parts, using hand tools or portable power tools.
- Inspect individual parts, assemblies, or installations, using measuring instruments, such as calipers, scales, or micrometers.
- Develop or lay out patterns, using computerized metalworking equipment.
- Convert blueprints into shop drawings to be followed in the construction or assembly of sheet metal products.
- Perform sheet metal work necessary for solar panel installations.
- Verify that heating, ventilating, and air conditioning (HVAC) systems are designed, installed, and calibrated in accordance with green certification standards, such as those of Leadership in Energy and Environmental Design (LEED).
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
- Finish parts, using hacksaws or hand, rotary, or squaring shears.
- Secure metal roof panels in place by interlocking and fastening grooved panel edges.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.
- Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.
- Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.
- Waterproof or restore concrete surfaces, using appropriate compounds.
- Fabricate concrete beams, columns, and panels.
- Check the forms that hold the concrete to see that they are properly constructed.
- Set the forms that hold concrete to the desired pitch and depth, and align them.
- Spread, level, and smooth concrete, using rake, shovel, hand or power trowel, hand or power screed, and float.
- Monitor how the wind, heat, or cold affect the curing of the concrete throughout the entire process.
- Mold expansion joints and edges, using edging tools, jointers, and straightedge.
- Signal truck driver to position truck to facilitate pouring concrete, and move chute to direct concrete on forms.
- Direct the casting of the concrete and supervise laborers who use shovels or special tools to spread it.
- Produce rough concrete surface, using broom.
- Operate power vibrator to compact concrete.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Chip, scrape, and grind high spots, ridges, and rough projections to finish concrete, using pneumatic chisels, power grinders, or hand tools.
- Cut out damaged areas, drill holes for reinforcing rods, and position reinforcing rods to repair concrete, using power saw and drill.
- Wet concrete surface, and rub with stone to smooth surface and obtain specified finish.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Build wooden molds, and clamp molds around area to be repaired, using hand tools.
- Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.
- Polish surface, using polishing or surfacing machine.
- Cut metal division strips, and press them into terrazzo base so that top edges form desired design or pattern.
- Push roller over surface to embed chips in surface.
- Apply muriatic acid to clean surface, and rinse with water.
- Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.
- Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.
- Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.
- Waterproof or restore concrete surfaces, using appropriate compounds.
- Fabricate concrete beams, columns, and panels.
- Paint traffic control lines and place pavement traffic messages, by hand or using machines.
- Erect, install, or repair guardrails, road shoulders, berms, highway markers, warning signals, and highway lighting, using hand tools and power tools.
- Apply poisons along roadsides and in animal burrows to eliminate unwanted roadside vegetation and rodents.
- Place and remove snow fences used to prevent the accumulation of drifting snow on highways.
- Set out signs and cones around work areas to divert traffic.
- Flag motorists to warn them of obstacles or repair work ahead.
- Perform preventative maintenance on vehicles and heavy equipment.
- Drive trucks to transport crews and equipment to work sites.
- Clean and clear debris from culverts, catch basins, drop inlets, ditches, and other drain structures.
- Drive heavy equipment and vehicles with adjustable attachments to sweep debris from paved surfaces, mow grass and weeds, remove snow and ice, and spread salt and sand.
- Haul and spread sand, gravel, and clay to fill washouts and repair road shoulders.
- Inspect, clean, and repair drainage systems, bridges, tunnels, and other structures.
- Remove litter and debris from roadways, including debris from rock and mud slides.
- Dump, spread, and tamp asphalt, using pneumatic tampers, to repair joints and patch broken pavement.
- Perform roadside landscaping work, such as clearing weeds and brush, and planting and trimming trees.
- Measure and mark locations for installation of markers, using tape, string, or chalk.
- Apply oil to road surfaces, using sprayers.
- Inspect markers to verify accurate installation.
- Blend compounds to form adhesive mixtures used for marker installation.
- Paint traffic control lines and place pavement traffic messages, by hand or using machines.
- Erect, install, or repair guardrails, road shoulders, berms, highway markers, warning signals, and highway lighting, using hand tools and power tools.
- Apply poisons along roadsides and in animal burrows to eliminate unwanted roadside vegetation and rodents.
- Place and remove snow fences used to prevent the accumulation of drifting snow on highways.
- Apply paint, stain, varnish, enamel, or other finishes to equipment, buildings, bridges, or other structures, using brushes, spray guns, or rollers.
- Erect scaffolding or swing gates, or set up ladders, to work above ground level.
- Waterproof buildings, using waterproofers or caulking.
- Spray or brush hot plastics or pitch onto surfaces.
- Fill cracks, holes, or joints with caulk, putty, plaster, or other fillers, using caulking guns or putty knives.
- Cover surfaces with dropcloths or masking tape and paper to protect surfaces during painting.
- Smooth surfaces, using sandpaper, scrapers, brushes, steel wool, or sanding machines.
- Read work orders or receive instructions from supervisors or homeowners to determine work requirements.
- Apply primers or sealers to prepare new surfaces, such as bare wood or metal, for finish coats.
- Mix and match colors of paint, stain, or varnish with oil or thinning and drying additives to obtain desired colors and consistencies.
- Calculate amounts of required materials and estimate costs, based on surface measurements or work orders.
- Polish final coats to specified finishes.
- Wash and treat surfaces with oil, turpentine, mildew remover, or other preparations, and sand rough spots to ensure that finishes will adhere properly.
- Select and purchase tools or finishes for surfaces to be covered, considering durability, ease of handling, methods of application, and customers' wishes.
- Remove old finishes by stripping, sanding, wire brushing, burning, or using water or abrasive blasting.
- Remove fixtures such as pictures, door knobs, lamps, or electric switch covers prior to painting.
- Use special finishing techniques such as sponging, ragging, layering, or faux finishing.
- Cut stencils and brush or spray lettering or decorations on surfaces.
- Bake finishes on painted or enameled articles, using baking ovens.
- Apply paint, stain, varnish, enamel, or other finishes to equipment, buildings, bridges, or other structures, using brushes, spray guns, or rollers.
- Erect scaffolding or swing gates, or set up ladders, to work above ground level.
- Waterproof buildings, using waterproofers or caulking.
- Spray or brush hot plastics or pitch onto surfaces.
- Spread roofing paper on surface of foundation and spread concrete onto roofing paper with trowel to form terrazzo base.
- Wash polished terrazzo surface, using cleaner and water, and apply sealer and curing agent according to manufacturer's specifications, using brush or sprayer.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth with a trowel.
- Measure designated amounts of ingredients for terrazzo or grout, according to standard formulas and specifications, using graduated containers and scales, and load ingredients into portable mixer.
- Grind surfaces with a power grinder, or polish surfaces with polishing or surfacing machines.
- Cut metal division strips and press them into the terrazzo base for joints or changes of color to form designs or patterns or to help prevent cracks.
- Blend marble chip mixtures, place into panels, and push a roller over the surface to embed the chips.
- Modify mixing, grouting, grinding, or cleaning procedures, according to type of installation or material used.
- Spread, level, or smooth concrete or terrazzo mixtures to form bases or finished surfaces, using rakes, shovels, hand or power trowels, hand or power screeds, or floats.
- Grind curved surfaces or areas inaccessible to surfacing machine, such as stairways or cabinet tops, with portable hand grinder.
- Position and secure moisture membrane and wire mesh in preparation for pouring base materials for terrazzo installation.
- Fill slight grinding depressions with matching grout material and hand-trowel for a smooth, uniform surface.
- Clean installation site, mixing and storage areas, tools, machines, and equipment, and store materials and equipment.
- Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.
- Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.
- Chip, scrape, or grind high spots, ridges, or rough projections to finish concrete, using pneumatic chisel, hand chisel, or other hand tools.
- Mold expansion joints and edges, using edging tools, jointers, or straightedges.
- Move terrazzo installation materials, tools, machines, or work devices to work areas, manually or using wheelbarrow.
- Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.
- Repair concrete by cutting out damaged areas, drilling holes for reinforcing rods, and positioning reinforcing rods, using power saw and drill.
- Precast terrazzo blocks in wooden forms.
- Wet concrete surface and rub with stone to smooth surface and obtain specified finish.
- Build wooden molds, clamping molds around areas to be repaired, or setting up frames to the proper depth and alignment.
- Produce rough concrete surface, using broom.
- Remove frames when the foundation is dry.
- Signal truck driver to position truck to facilitate pouring concrete and move chute to direct concrete on forms.
- Spread roofing paper on surface of foundation and spread concrete onto roofing paper with trowel to form terrazzo base.
- Wash polished terrazzo surface, using cleaner and water, and apply sealer and curing agent according to manufacturer's specifications, using brush or sprayer.
- Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth with a trowel.
- Paint a variety of objects related to electrical functions.
- Erect electrical system components and barricades, and rig scaffolds, hoists, and shoring.
- Strip insulation from wire ends, using wire stripping pliers, and attach wires to terminals for subsequent soldering.
- Trace out short circuits in wiring, using test meter.
- Measure, cut, and bend wire and conduit, using measuring instruments and hand tools.
- Examine electrical units for loose connections and broken insulation and tighten connections, using hand tools.
- Maintain tools, vehicles, and equipment and keep parts and supplies in order.
- Drill holes and pull or push wiring through openings, using hand and power tools.
- Clean work area and wash parts.
- Perform semi-skilled and unskilled laboring duties related to the installation, maintenance and repair of a wide variety of electrical systems and equipment.
- Thread conduit ends, connect couplings, and fabricate and secure conduit support brackets, using hand tools.
- Disassemble defective electrical equipment, replace defective or worn parts, and reassemble equipment, using hand tools.
- Construct controllers and panels, using power drills, drill presses, taps, saws, and punches.
- Transport tools, materials, equipment, and supplies to work site by hand, handtruck, or heavy, motorized truck.
- String transmission lines or cables through ducts or conduits, under the ground, through equipment, or to towers.
- Install copper-clad ground rods, using a manual post driver.
- Dig trenches or holes for installation of conduit or supports.
- Raise, lower, or position equipment, tools, and materials, using hoist, hand line, or block and tackle.
- Bolt component parts together to form tower assemblies, using hand tools.
- Trim trees and clear undergrowth along right-of-way.
- Requisition materials, using warehouse requisition or release forms.
- Solder electrical connections, using soldering iron.
- Break up concrete, using airhammer, to facilitate installation, construction, or repair of equipment.
- Operate heavy equipment, such as backhoes.
- Operate cutting torches and welding equipment, while working with conduit and metal components to construct devices associated with electrical functions.
- Paint a variety of objects related to electrical functions.
- Erect electrical system components and barricades, and rig scaffolds, hoists, and shoring.
- Paint railroad signs, such as speed limits or gate-crossing warnings.
- Spray ties, fishplates, or joints with oil to protect them from weathering.
- Patrol assigned track sections so that damaged or broken track can be located and reported.
- Repair or adjust track switches, using wrenches and replacement parts.
- Weld sections of track together, such as switch points and frogs.
- Observe leveling indicator arms to verify levelness and alignment of tracks.
- Operate single- or multiple-head spike driving machines to drive spikes into ties and secure rails.
- Operate track wrenches to tighten or loosen bolts at joints that hold ends of rails together.
- Cut rails to specified lengths, using rail saws.
- Lubricate machines, change oil, or fill hydraulic reservoirs to specified levels.
- Drill holes through rails, tie plates, or fishplates for insertion of bolts or spikes, using power drills.
- Clean tracks or clear ice or snow from tracks or switch boxes.
- Clean, grade, or level ballast on railroad tracks.
- Raise rails, using hydraulic jacks, to allow for tie removal and replacement.
- Adjust controls of machines that spread, shape, raise, level, or align track, according to specifications.
- Dress and reshape worn or damaged railroad switch points or frogs, using portable power grinders.
- Clean or make minor repairs to machines or equipment.
- Grind ends of new or worn rails to attain smooth joints, using portable grinders.
- Operate single- or multiple-head spike pullers to pull old spikes from ties.
- String and attach wire-guidelines machine to rails so that tracks or rails can be aligned or leveled.
- Engage mechanisms that lay tracks or rails to specified gauges.
- Drive graders, tamping machines, brooms, or ballast spreading machines to redistribute gravel or ballast between rails.
- Drive vehicles that automatically move and lay tracks or rails over sections of track to be constructed, repaired, or maintained.
- Turn wheels of machines, using lever controls, to adjust guidelines for track alignments or grades, following specifications.
- Push controls to close grasping devices on track or rail sections so that they can be raised or moved.
- Operate tie-adzing machines to cut ties and permit insertion of fishplates that hold rails.
- Paint railroad signs, such as speed limits or gate-crossing warnings.
- Spray ties, fishplates, or joints with oil to protect them from weathering.