- Perform minor assembly, such as fastening parts with nuts, bolts, or screws, using power tools or hand tools.
Occupations with related tasks Save Table: XLSX CSV
| Closely Related Tasks | All Related Tasks | Job Zone | Code | Occupation |
| 4 | 4 | 2 | 51-2011.00 | Aircraft Structure, Surfaces, Rigging, and Systems Assemblers |
| 2 | 3 | 3 | 51-4061.00 | Model Makers, Metal and Plastic |
| 2 | 2 | 2 | 51-4122.00 | Welding, Soldering, and Brazing Machine Setters, Operators, and Tenders |
| 1 | 4 | 2 | 51-9195.00 | Molders, Shapers, and Casters, Except Metal and Plastic |
| 1 | 2 | 2 | 51-4192.00 | Layout Workers, Metal and Plastic |
| 1 | 1 | 2 | 51-2021.00 | Coil Winders, Tapers, and Finishers |
| 1 | 1 | 2 | 51-2061.00 | Timing Device Assemblers and Adjusters |
- Assemble parts, fittings, or subassemblies on aircraft, using layout tools, hand tools, power tools, or fasteners, such as bolts, screws, rivets, or clamps.
- Fabricate parts needed for assembly or installation, using shop machinery or equipment.
- Assemble prefabricated parts to form subassemblies.
- Assemble prototypes or integrated-technology demonstrators of new or emerging environmental technologies for aircraft.
- Read blueprints, illustrations, or specifications to determine layouts, sequences of operations, or identities or relationships of parts.
- Attach brackets, hinges, or clips to secure or support components or subassemblies, using bolts, screws, rivets, chemical bonding, or welding.
- Inspect or test installed units, parts, systems, or assemblies for fit, alignment, performance, defects, or compliance with standards, using measuring instruments or test equipment.
- Adjust, repair, rework, or replace parts or assemblies to ensure proper operation.
- Cut, trim, file, bend, or smooth parts to ensure proper fit and clearance.
- Layout and mark reference points and locations for installation of parts or components, using jigs, templates, or measuring and marking instruments.
- Clean, oil, or coat system components, as necessary, before assembly or attachment.
- Set, align, adjust, or synchronize aircraft armament or rigging or control system components to established tolerances or requirements, using sighting devices and hand tools.
- Join structural assemblies, such as wings, tails, or fuselage.
- Position and align subassemblies in jigs or fixtures, using measuring instruments and following blueprint lines and index points.
- Swage fittings onto cables, using swaging machines.
- Manually install structural assemblies or signal crane operators to position assemblies for joining.
- Align, fit, assemble, connect, or install system components, using jigs, fixtures, measuring instruments, hand tools, or power tools.
- Set up or operate machines or systems to crimp, cut, bend, form, swage, flare, bead, burr, or straighten tubing, according to specifications.
- Place and connect control cables to electronically controlled units, using hand tools, ring locks, cotter keys, threaded connectors, turnbuckles, or related devices.
- Install mechanical linkages and actuators, using tensiometers to verify tension of cables.
- Clean aircraft structures, parts, or components, using aqueous, semi-aqueous, aliphatic hydrocarbon, or organic solvent cleaning products or techniques to reduce carbon or other harmful emissions.
- Install accessories in swaging machines, using hand tools.
- Mark identifying information on tubing or cable assemblies, using etching devices, labels, rubber stamps, or other methods.
- Verify dimensions of cable assemblies or positions of fittings, using measuring instruments.
- Weld tubing and fittings or solder cable ends, using tack welders, induction brazing chambers, or other equipment.
- Splice cables, using clamps and fittings, or reweave cable strands.
- Fit and fasten sheet metal coverings to surface areas or other sections of aircraft prior to welding or riveting.
- Capture or segregate waste material, such as aluminum swarf, machine cutting fluid, or solvents, for recycling or environmentally responsible disposal.
- Cut cables and tubing, using master templates, measuring instruments, and cable cutters or saws.
- Monitor robotic assembly equipment, such as snake-arm robots, used to assemble, seal, or swage aircraft structures.
- Assemble parts, fittings, or subassemblies on aircraft, using layout tools, hand tools, power tools, or fasteners, such as bolts, screws, rivets, or clamps.
- Fabricate parts needed for assembly or installation, using shop machinery or equipment.
- Assemble prefabricated parts to form subassemblies.
- Assemble prototypes or integrated-technology demonstrators of new or emerging environmental technologies for aircraft.
- Align, fit, and join parts, using bolts and screws or by welding or gluing.
- Assemble mechanical, electrical, and electronic components into models or prototypes, using hand tools, power tools, and fabricating machines.
- Devise and construct tools, dies, molds, jigs, and fixtures, or modify existing tools and equipment.
- Study blueprints, drawings, and sketches to determine material dimensions, required equipment, and operations sequences.
- Inspect and test products to verify conformance to specifications, using precision measuring instruments or circuit testers.
- Drill, countersink, and ream holes in parts and assemblies for bolts, screws, and other fasteners, using power tools.
- Cut, shape, and form metal parts, using lathes, power saws, snips, power brakes and shears, files, and mallets.
- Set up and operate machines, such as lathes, drill presses, punch presses, or bandsaws, to fabricate prototypes or models.
- Rework or alter component model or parts as required to ensure that products meet standards.
- Grind, file, and sand parts to finished dimensions.
- Program computer numerical control (CNC) machines to fabricate model parts.
- Lay out and mark reference points and dimensions on materials, using measuring instruments and drawing or scribing tools.
- Use computer-aided design (CAD) and computer-aided manufacturing (CAM) software or hardware to fabricate model parts.
- Consult and confer with engineering personnel to discuss developmental problems and to recommend product modifications.
- Record specifications, production operations, and final dimensions of models for use in establishing operating standards and procedures.
- Wire and solder electrical and electronic connections and components.
- Align, fit, and join parts, using bolts and screws or by welding or gluing.
- Assemble mechanical, electrical, and electronic components into models or prototypes, using hand tools, power tools, and fabricating machines.
- Devise and construct tools, dies, molds, jigs, and fixtures, or modify existing tools and equipment.
- Assemble, align, and clamp workpieces into holding fixtures to bond, heat-treat, or solder fabricated metal components.
- Lay out, fit, or connect parts to be bonded, calculating production measurements, as necessary.
- Inspect, measure, or test completed metal workpieces to ensure conformance to specifications, using measuring and testing devices.
- Read blueprints, work orders, or production schedules to determine product or job instructions or specifications.
- Set up, operate, or tend welding machines that join or bond components to fabricate metal products or assemblies.
- Correct problems by adjusting controls or by stopping machines and opening holding devices.
- Give directions to other workers regarding machine set-up and use.
- Select, position, align, and bolt jigs, holding fixtures, guides, or stops onto machines, using measuring instruments and hand tools.
- Mark weld points and positions of components on workpieces, using rules, squares, templates, or scribes.
- Transfer components, metal products, or assemblies, using moving equipment.
- Clean, lubricate, maintain, and adjust equipment to maintain efficient operation, using air hoses, cleaning fluids, and hand tools.
- Prepare metal surfaces or workpieces, using hand-operated equipment, such as grinders, cutters, or drills.
- Conduct trial runs before welding, soldering, or brazing, and make necessary adjustments to equipment.
- Remove completed workpieces or parts from machinery, using hand tools.
- Tend auxiliary equipment used in welding processes.
- Load or feed workpieces into welding machines to join or bond components.
- Observe meters, gauges, or machine operations to ensure that soldering or brazing processes meet specifications.
- Turn and press knobs and buttons or enter operating instructions into computers to adjust and start welding machines.
- Compute and record settings for new work, applying knowledge of metal properties, principles of welding, and shop mathematics.
- Set dials and timing controls to regulate electrical current, gas flow pressure, heating or cooling cycles, or shut-off.
- Record operational information on specified production reports.
- Select torch tips, alloys, flux, coil, tubing, or wire, according to metal types or thicknesses, data charts, or records.
- Fill hoppers and position spouts to direct flow of flux or manually brush flux onto seams of workpieces.
- Start, monitor, and adjust robotic welding production lines.
- Devise or build fixtures or jigs used to hold parts in place during welding, brazing, or soldering.
- Add chemicals or materials to workpieces or machines to facilitate bonding or to cool workpieces.
- Immerse completed workpieces into water or acid baths to cool and clean components.
- Dress electrodes, using tip dressers, files, emery cloths, or dressing wheels.
- Anneal finished workpieces to relieve internal stress.
- Assemble, align, and clamp workpieces into holding fixtures to bond, heat-treat, or solder fabricated metal components.
- Lay out, fit, or connect parts to be bonded, calculating production measurements, as necessary.
- Align and assemble parts to produce completed products, using gauges and hand tools.
- Assemble, insert, and adjust wires, tubes, cores, fittings, rods, or patterns into molds, using hand tools and depth gauges.
- Operate molding machines that compact sand in flasks to form molds.
- Construct or form molds for use in casting clay or plaster objects, using plaster, fiberglass, rubber, casting machines, patterns, or flasks.
- Read work orders or examine parts to determine parts or sections of products to be produced.
- Trim or remove excess material, using scrapers, knives, or band saws.
- Brush or spray mold surfaces with parting agents or insert paper into molds to ensure smoothness and prevent sticking or seepage.
- Engrave or stamp identifying symbols, letters, or numbers on products.
- Clean, finish, and lubricate molds and mold parts.
- Separate models or patterns from molds and examine products for accuracy.
- Set the proper operating temperature for each casting.
- Load or stack filled molds in ovens, dryers, or curing boxes, or on storage racks or carts.
- Operate and adjust controls of heating equipment to melt material or to cure, dry, or bake filled molds.
- Select sizes and types of molds according to instructions.
- Patch broken edges or fractures, using clay or plaster.
- Withdraw cores or other loose mold members after castings solidify.
- Repair mold defects, such as cracks or broken edges, using patterns, mold boxes, or hand tools.
- Measure and cut products to specified dimensions, using measuring and cutting instruments.
- Smooth surfaces of molds, using scraping tools or sandpaper.
- Measure ingredients and mix molding, casting material, or sealing compounds to prescribed consistencies, according to formulas.
- Remove excess materials and level and smooth wet mold mixtures.
- Place forms around models and separately immerse each half portion of a model in plaster, wax, or other mold-making materials.
- Verify dimensions of products, using measuring instruments, such as calipers, vernier gauges, or protractors.
- Bore holes or cut grates, risers, or pouring spouts in molds, using power tools.
- Locate and scribe parting lines on patterns, using measuring instruments, such as calipers, squares, or depth gauges.
- Tap or tilt molds to ensure uniform distribution of materials.
- Pour, pack, spread, or press plaster, concrete, or other materials into or around models or molds.
- Align and assemble parts to produce completed products, using gauges and hand tools.
- Assemble, insert, and adjust wires, tubes, cores, fittings, rods, or patterns into molds, using hand tools and depth gauges.
- Operate molding machines that compact sand in flasks to form molds.
- Construct or form molds for use in casting clay or plaster objects, using plaster, fiberglass, rubber, casting machines, patterns, or flasks.
- Lay out and fabricate metal structural parts such as plates, bulkheads, and frames.
- Design and prepare templates of wood, paper, or metal.
- Mark curves, lines, holes, dimensions, and welding symbols onto workpieces, using scribes, soapstones, punches, and hand drills.
- Plan locations and sequences of cutting, drilling, bending, rolling, punching, and welding operations, using compasses, protractors, dividers, and rules.
- Fit and align fabricated parts to be welded or assembled.
- Locate center lines and verify template positions, using measuring instruments such as gauge blocks, height gauges, and dial indicators.
- Plan and develop layouts from blueprints and templates, applying knowledge of trigonometry, design, effects of heat, and properties of metals.
- Compute layout dimensions, and determine and mark reference points on metal stock or workpieces for further processing, such as welding and assembly.
- Lift and position workpieces in relation to surface plates, manually or with hoists, and using parallel blocks and angle plates.
- Install doors, hatches, brackets, and clips.
- Brace parts in position within hulls or ships for riveting or welding.
- Inspect machined parts to verify conformance to specifications.
- Add dimensional details to blueprints or drawings made by other workers.
- Apply pigment to layout surfaces, using paint brushes.
- Lay out and fabricate metal structural parts such as plates, bulkheads, and frames.
- Design and prepare templates of wood, paper, or metal.
- Line slots with sheet insulation, and insert coils into slots.
- Operate or tend wire-coiling machines to wind wire coils used in electrical components such as resistors and transformers, and in electrical equipment and instruments such as bobbins and generators.
- Attach, alter, and trim materials such as wire, insulation, and coils, using hand tools.
- Cut, strip, and bend wire leads at ends of coils, using pliers and wire scrapers.
- Review work orders and specifications to determine materials needed and types of parts to be processed.
- Select and load materials such as workpieces, objects, and machine parts onto equipment used in coiling processes.
- Record production and operational data on specified forms.
- Stop machines to remove completed components, using hand tools.
- Examine and test wired electrical components such as motors, armatures, and stators, using measuring devices, and record test results.
- Apply solutions or paints to wired electrical components, using hand tools, and bake components.
- Disassemble and assemble motors, and repair and maintain electrical components and machinery parts, using hand tools.
- Line slots with sheet insulation, and insert coils into slots.
- Assemble and install components of timepieces to complete mechanisms, using watchmakers' tools and loupes.
- Observe operation of timepiece parts and subassemblies to determine accuracy of movement, and to diagnose causes of defects.
- Test operation and fit of timepiece parts and subassemblies, using electronic testing equipment, tweezers, watchmakers' tools, and loupes.
- Replace specified parts to repair malfunctioning timepieces, using watchmakers' tools, loupes, and holding fixtures.
- Disassemble timepieces such as watches, clocks, and chronometers so that repairs can be made.
- Clean and lubricate timepiece parts and assemblies, using solvents, buff sticks, and oil.
- Examine components of timepieces such as watches, clocks, or chronometers for defects, using loupes or microscopes.
- Bend parts, such as hairsprings, pallets, barrel covers, and bridges, to correct deficiencies in truing or endshake, using tweezers.
- Change timing weights on balance wheels to correct deficient timing.
- Adjust sizes or positioning of timepiece parts to achieve specified fit or function, using calipers, fixtures, and loupes.
- Mount hairsprings and balance wheel assemblies between jaws of truing calipers.
- Estimate spaces between collets and first inner coils to determine if spaces are within acceptable limits.
- Bend inner coils of springs away from or toward collets, using tweezers, to locate centers of collets in centers of springs, and to correct errors resulting from faulty colleting of coils.
- Turn wheels of calipers and examine springs, using loupes, to determine if center coils appear as perfect circles.
- Examine and adjust hairspring assemblies to ensure horizontal and circular alignment of hairsprings, using calipers, loupes, and watchmakers' tools.
- Review blueprints, sketches, or work orders to gather information about tasks to be completed.
- Tighten or replace loose jewels, using watchmakers' tools.
- Assemble and install components of timepieces to complete mechanisms, using watchmakers' tools and loupes.
