- Assemble and install new pipe organs and pianos in buildings.
Occupations with related tasks Save Table: XLSX CSV
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Connect car frames to counterweights, using steel cables.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Connect electrical wiring to control panels and electric motors.
- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Disassemble defective units, and repair or replace parts such as locks, gears, cables, and electric wiring.
- Check that safety regulations and building codes are met, and complete service reports verifying conformance to standards.
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Adjust safety controls, counterweights, door mechanisms, and components such as valves, ratchets, seals, and brake linings.
- Read and interpret blueprints to determine the layout of system components, frameworks, and foundations, and to select installation equipment.
- Maintain log books that detail all repairs and checks performed.
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Participate in additional training to keep skills up to date.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Install outer doors and door frames at elevator entrances on each floor of a structure.
- Bolt or weld steel rails to the walls of shafts to guide elevators, working from scaffolding or platforms.
- Cut prefabricated sections of framework, rails, and other components to specified dimensions.
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Connect car frames to counterweights, using steel cables.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Connect electrical wiring to control panels and electric motors.
- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Insert waterproof sealers, bullets, and/or powder charges into guns, and screw gun ports back into place.
- Examine blast areas to determine amounts and kinds of explosive charges needed and to ensure that safety laws are observed.
- Tie specified lengths of delaying fuses into patterns in order to time sequences of explosions.
- Place safety cones around blast areas to alert other workers of danger zones, and signal workers as necessary to ensure that they clear blast sites prior to explosions.
- Place explosive charges in holes or other spots; then detonate explosives to demolish structures or to loosen, remove, or displace earth, rock, or other materials.
- Insert, pack, and pour explosives, such as dynamite, ammonium nitrate, black powder, or slurries into blast holes; then shovel drill cuttings, admit water into boreholes, and tamp material to compact charges.
- Mark patterns, locations, and depths of charge holes for drilling, and issue drilling instructions.
- Compile and keep gun and explosives records in compliance with local and federal laws.
- Measure depths of drilled blast holes, using weighted tape measures.
- Connect electrical wire to primers, and cover charges or fill blast holes with clay, drill chips, sand, or other material.
- Lay primacord between rows of charged blast holes, and tie cord into main lines to form blast patterns.
- Verify detonation of charges by observing control panels, or by listening for the sounds of blasts.
- Move and store inventories of explosives, loaded perforating guns, and other materials, according to established safety procedures.
- Light fuses, drop detonating devices into wells or boreholes, or activate firing devices with plungers, dials, or buttons, in order to set off single or multiple blasts.
- Drive trucks to transport explosives and blasting equipment to blasting sites.
- Cut specified lengths of primacord and attach primers to cord ends.
- Maintain inventory levels, ordering new supplies as necessary.
- Repair and service blasting, shooting, and automotive equipment, and electrical wiring and instruments, using hand tools.
- Set up and operate short-wave radio or field telephone equipment to transmit and receive blast information.
- Clean, gauge, and lubricate gun ports.
- Lower perforating guns into wells, using hoists; then use measuring devices and instrument panels to position guns in correct positions for taking samples.
- Create and lay out designs for drill and blast patterns.
- Document geological formations encountered during work.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Set up and operate equipment such as hoists, jackhammers, and drills, in order to bore charge holes.
- Signal crane operators to move equipment.
- Operate drones for aerial survey of blast sites and for post-blast damage assessment.
- Assemble and position equipment, explosives, and blasting caps in holes at specified depths, or load perforating guns or torpedoes with explosives.
- Insert waterproof sealers, bullets, and/or powder charges into guns, and screw gun ports back into place.
- Splice fibers, using fusion splicing or other techniques.
- Set up or operate assembly or processing equipment, such as lasers, cameras, die bonders, wire bonders, dispensers, reflow ovens, soldering irons, die shears, wire pull testers, temperature or humidity chambers, or optical spectrum analyzers.
- Assemble fiber optical, optoelectronic, or free-space optics components, subcomponents, assemblies, or subassemblies.
- Assemble or adjust parts or related electrical units of prototypes to prepare for testing.
- Design, build, or modify fixtures used to assemble parts.
- Assemble components of energy-efficient optical communications systems involving photonic switches, optical backplanes, or optoelectronic interfaces.
- Compute or record photonic test data.
- Maintain clean working environments, according to clean room standards.
- Adjust or maintain equipment, such as lasers, laser systems, microscopes, oscilloscopes, pulse generators, power meters, beam analyzers, or energy measurement devices.
- Document procedures, such as calibration of optical or fiber optic equipment.
- Assist scientists or engineers in the conduct of photonic experiments.
- Test or perform failure analysis for optomechanical or optoelectrical products, according to test plans.
- Assist engineers in the development of new products, fixtures, tools, or processes.
- Recommend optical or optic equipment design or material changes to reduce costs or processing times.
- Set up or operate prototype or test apparatus, such as control consoles, collimators, recording equipment, or cables.
- Monitor inventory levels and order supplies as necessary.
- Optimize photonic process parameters by making prototype or production devices.
- Build prototype optomechanical devices for use in equipment such as aerial cameras, gun sights, or telescopes.
- Terminate, cure, polish, or test fiber cables with mechanical connectors.
- Perform diagnostic analyses of processing steps, using analytical or metrological tools, such as microscopy, profilometry, or ellipsometry devices.
- Repair or calibrate products, such as surgical lasers.
- Lay out cutting lines for machining, using drafting tools.
- Mix, pour, or use processing chemicals or gases according to safety standards or established operating procedures.
- Fabricate devices, such as optoelectronic or semiconductor devices.
- Splice fibers, using fusion splicing or other techniques.
- Set up or operate assembly or processing equipment, such as lasers, cameras, die bonders, wire bonders, dispensers, reflow ovens, soldering irons, die shears, wire pull testers, temperature or humidity chambers, or optical spectrum analyzers.
- Assemble fiber optical, optoelectronic, or free-space optics components, subcomponents, assemblies, or subassemblies.
- Assemble or adjust parts or related electrical units of prototypes to prepare for testing.
- Design, build, or modify fixtures used to assemble parts.
- Assemble components of energy-efficient optical communications systems involving photonic switches, optical backplanes, or optoelectronic interfaces.
- Connect reactor to computer, using hand tools and power tools.
- Place semiconductor wafers in processing containers or equipment holders, using vacuum wand or tweezers.
- Set, adjust, and readjust computerized or mechanical equipment controls to regulate power level, temperature, vacuum, and rotation speed of furnace, according to crystal growing specifications.
- Etch, lap, polish, or grind wafers or ingots to form circuitry and change conductive properties, using etching, lapping, polishing, or grinding equipment.
- Align photo mask pattern on photoresist layer, expose pattern to ultraviolet light, and develop pattern, using specialized equipment.
- Manipulate valves, switches, and buttons, or key commands into control panels to start semiconductor processing cycles.
- Maintain processing, production, and inspection information and reports.
- Inspect materials, components, or products for surface defects and measure circuitry, using electronic test equipment, precision measuring instruments, microscope, and standard procedures.
- Clean semiconductor wafers using cleaning equipment, such as chemical baths, automatic wafer cleaners, or blow-off wands.
- Study work orders, instructions, formulas, and processing charts to determine specifications and sequence of operations.
- Load and unload equipment chambers and transport finished product to storage or to area for further processing.
- Clean and maintain equipment, including replacing etching and rinsing solutions and cleaning bath containers and work area.
- Load semiconductor material into furnace.
- Monitor operation and adjust controls of processing machines and equipment to produce compositions with specific electronic properties, using computer terminals.
- Count, sort, and weigh processed items.
- Calculate etching time based on thickness of material to be removed from wafers or crystals.
- Inspect equipment for leaks, diagnose malfunctions, and request repairs.
- Stamp, etch, or scribe identifying information on finished component according to specifications.
- Scribe or separate wafers into dice.
- Measure and weigh amounts of crystal growing materials, mix and grind materials, load materials into container, and monitor processing procedures to help identify crystal growing problems.
- Connect reactor to computer, using hand tools and power tools.
- Place semiconductor wafers in processing containers or equipment holders, using vacuum wand or tweezers.
- Set, adjust, and readjust computerized or mechanical equipment controls to regulate power level, temperature, vacuum, and rotation speed of furnace, according to crystal growing specifications.
- Etch, lap, polish, or grind wafers or ingots to form circuitry and change conductive properties, using etching, lapping, polishing, or grinding equipment.
- Align photo mask pattern on photoresist layer, expose pattern to ultraviolet light, and develop pattern, using specialized equipment.
- Install or maintain electrical control systems, industrial automation systems, or electrical equipment, including control circuits, variable speed drives, or programmable logic controllers.
- Assemble electrical systems or prototypes, using hand tools or measuring instruments.
- Assemble, test, or maintain circuitry or electronic components, according to engineering instructions, technical manuals, or knowledge of electronics, using hand or power tools.
- Construct and evaluate electrical components for consumer electronics applications such as fuel cells for consumer electronic devices, power saving devices for computers or televisions, or energy efficient power chargers.
- Modify, maintain, or repair electronics equipment or systems to ensure proper functioning.
- Replace defective components or parts, using hand tools and precision instruments.
- Set up and operate specialized or standard test equipment to diagnose, test, or analyze the performance of electronic components, assemblies, or systems.
- Read blueprints, wiring diagrams, schematic drawings, or engineering instructions for assembling electronics units, applying knowledge of electronic theory and components.
- Identify and resolve equipment malfunctions, working with manufacturers or field representatives as necessary to procure replacement parts.
- Review electrical engineering plans to ensure adherence to design specifications and compliance with applicable electrical codes and standards.
- Review existing electrical engineering criteria to identify necessary revisions, deletions, or amendments to outdated material.
- Maintain system logs or manuals to document testing or operation of equipment.
- Select electronics equipment, components, or systems to meet functional specifications.
- Calculate design specifications or cost, material, and resource estimates, and prepare project schedules and budgets.
- Educate equipment operators on the proper use of equipment.
- Supervise the installation or operation of electronic equipment or systems.
- Compile and maintain records documenting engineering schematics, installed equipment, installation or operational problems, resources used, repairs, or corrective action performed.
- Modify electrical prototypes, parts, assemblies, or systems to correct functional deviations.
- Integrate software or hardware components, using computer, microprocessor, or control architecture.
- Procure parts and maintain inventory and related documentation.
- Participate in training or continuing education activities to stay abreast of engineering or industry advances.
- Research equipment or component needs, sources, competitive prices, delivery times, or ongoing operational costs.
- Provide user applications or engineering support or recommendations for new or existing equipment with regard to installation, upgrades, or enhancements.
- Specify, coordinate, or conduct quality control or quality assurance programs or procedures.
- Produce electronics drawings or other graphics representing industrial control, instrumentation, sensors, or analog or digital telecommunications networks, using computer-aided design (CAD) software.
- Design or modify engineering schematics for electrical transmission and distribution systems or for electrical installation in residential, commercial, or industrial buildings, using computer-aided design (CAD) software.
- Interpret test information to resolve design-related problems.
- Conduct statistical studies to analyze or compare production costs for sustainable or nonsustainable designs.
- Participate in the development or testing of electrical aspects of new green technologies, such as lighting, optical data storage devices, and energy efficient televisions.
- Review, develop, or prepare maintenance standards.
- Install or maintain electrical control systems, industrial automation systems, or electrical equipment, including control circuits, variable speed drives, or programmable logic controllers.
- Assemble electrical systems or prototypes, using hand tools or measuring instruments.
- Assemble, test, or maintain circuitry or electronic components, according to engineering instructions, technical manuals, or knowledge of electronics, using hand or power tools.
- Construct and evaluate electrical components for consumer electronics applications such as fuel cells for consumer electronic devices, power saving devices for computers or televisions, or energy efficient power chargers.
- Install electrical or electronic parts and hardware in housings or assemblies, using soldering equipment and hand tools.
- Fabricate or assemble mechanical, electrical, or electronic components or assemblies.
- Align, fit, or assemble component parts, using hand or power tools, fixtures, templates, or microscopes.
- Test performance of electromechanical assemblies, using test instruments such as oscilloscopes, electronic voltmeters, or bridges.
- Install or program computer hardware or machine or instrumentation software in microprocessor-based systems.
- Read blueprints, schematics, diagrams, or technical orders to determine methods and sequences of assembly.
- Modify, maintain, or repair electrical, electronic, or mechanical components, equipment, or systems to ensure proper functioning.
- Inspect parts for surface defects.
- Verify part dimensions or clearances to ensure conformance to specifications, using precision measuring instruments.
- Produce electrical, electronic, or mechanical drawings or other related documents or graphics necessary for electromechanical design, using computer-aided design (CAD) software.
- Select electromechanical equipment, materials, components, or systems to meet functional specifications.
- Establish and maintain inventory, records, or documentation systems.
- Develop, test, or program new robots.
- Prepare written documentation of electromechanical test results.
- Repair, rework, or calibrate hydraulic or pneumatic assemblies or systems to meet operational specifications or tolerances.
- Select and use laboratory, operational, or diagnostic techniques or test equipment to assess electromechanical circuits, equipment, processes, systems, or subsystems.
- Operate, test, or maintain robotic equipment used for green production applications, such as waste-to-energy conversion systems, minimization of material waste, or replacement of human operators in dangerous work environments.
- Determine whether selected electromechanical components comply with environmental standards and regulations.
- Develop or implement programs related to the environmental impact of engineering activities.
- Train others to install, use, or maintain robots.
- Analyze engineering designs of logic or digital circuitry, motor controls, instrumentation, or data acquisition for implementation into new or existing automated, servomechanical, or other electromechanical systems.
- Conduct statistical studies to analyze or compare production costs for sustainable and nonsustainable designs.
- Specify, coordinate, or conduct quality-control or quality-assurance programs and procedures.
- Operate metalworking machines to fabricate housings, jigs, fittings, or fixtures.
- Translate electromechanical drawings into design specifications, applying principles of engineering, thermal or fluid sciences, mathematics, or statistics.
- Identify energy-conserving production or fabrication methods, such as by bending metal rather than cutting and welding or casting metal.
- Assist engineers to implement electromechanical designs in industrial or other settings.
- Consult with machinists to ensure that electromechanical equipment or systems meet design specifications.
- Program and calibrate drones for specific missions or tasks, ensuring proper functionality and performance.
- Install electrical or electronic parts and hardware in housings or assemblies, using soldering equipment and hand tools.
- Fabricate or assemble mechanical, electrical, or electronic components or assemblies.
- Align, fit, or assemble component parts, using hand or power tools, fixtures, templates, or microscopes.
- Rotate through all the tasks required in a particular production process.
- Provide assistance in the production of wiring assemblies.
- Perform quality checks on products and parts.
- Review work orders and blueprints to ensure work is performed according to specifications.
- Determine work assignments and procedures.
- Supervise assemblers and train employees on job procedures.
- Shovel, sweep, or otherwise clean work areas.
- Maintain production equipment and machinery.
- Complete production reports to communicate team production level to management.
- Package finished products and prepare them for shipment.
- Operate machinery and heavy equipment, such as forklifts.
- Rotate through all the tasks required in a particular production process.
- Provide assistance in the production of wiring assemblies.
- Bolt together pump and engine parts.
- Lay gas and oil pipelines.
- Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.
- Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.
- Guide cranes to move loads about decks.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.
- Clean trucks used in the fields.
- Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.
- Supply equipment to rig floors as requested and provide assistance to roughnecks.
- Clean up spilled oil by bailing it into barrels.
- Dig drainage ditches around wells and storage tanks.
- Cut down and remove trees and brush to clear drill sites, to reduce fire hazards, and to make way for roads to sites.
- Bolt together pump and engine parts.
- Lay gas and oil pipelines.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Conduct pressure tests on vessels, such as boilers.
- Study blueprints to determine locations, relationships, or dimensions of parts.
- Examine boilers, pressure vessels, tanks, or vats to locate defects, such as leaks, weak spots, or defective sections, so that they can be repaired.
- Inspect assembled vessels or individual components, such as tubes, fittings, valves, controls, or auxiliary mechanisms, to locate any defects.
- Lay out plate, sheet steel, or other heavy metal and locate and mark bending and cutting lines, using protractors, compasses, and drawing instruments or templates.
- Bell, bead with power hammers, or weld pressure vessel tube ends to ensure leakproof joints.
- Locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments.
- Shape or fabricate parts, such as stacks, uptakes, or chutes, to adapt pressure vessels, heat exchangers, or piping to premises, using heavy-metalworking machines such as brakes, rolls, or drill presses.
- Position, align, and secure structural parts or related assemblies to boiler frames, tanks, or vats of pressure vessels, following blueprints.
- Clean pressure vessel equipment, using scrapers, wire brushes, and cleaning solvents.
- Repair or replace defective pressure vessel parts, such as safety valves or regulators, using torches, jacks, caulking hammers, power saws, threading dies, welding equipment, or metalworking machinery.
- Attach rigging and signal crane or hoist operators to lift heavy frame and plate sections or other parts into place.
- Straighten or reshape bent pressure vessel plates or structure parts, using hammers, jacks, or torches.
- Shape seams, joints, or irregular edges of pressure vessel sections or structural parts to attain specified fit of parts, using cutting torches, hammers, files, or metalworking machines.
- Bolt or arc weld pressure vessel structures and parts together, using wrenches or welding equipment.
- Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Connect sections of drill pipe, using hand tools and powered wrenches and tongs.
- Train crews, and introduce procedures to make drill work more safe and effective.
- Observe pressure gauge and move throttles and levers to control the speed of rotary tables, and to regulate pressure of tools at bottoms of boreholes.
- Count sections of drill rod to determine depths of boreholes.
- Push levers and brake pedals to control gasoline, diesel, electric, or steam draw works that lower and raise drill pipes and casings in and out of wells.
- Maintain records of footage drilled, location and nature of strata penetrated, materials and tools used, services rendered, and time required.
- Maintain and adjust machinery to ensure proper performance.
- Start and examine operation of slush pumps to ensure circulation and consistency of drilling fluid or mud in well.
- Locate and recover lost or broken bits, casings, and drill pipes from wells, using special tools.
- Weigh clay, and mix with water and chemicals to make drilling mud.
- Direct rig crews in drilling and other activities, such as setting up rigs and completing or servicing wells.
- Monitor progress of drilling operations, and select and change drill bits according to the nature of strata, using hand tools.
- Repair or replace defective parts of machinery, such as rotary drill rigs, water trucks, air compressors, and pumps, using hand tools.
- Clean and oil pulleys, blocks, and cables.
- Remove core samples during drilling to determine the nature of the strata being drilled.
- Cap wells with packers, or turn valves, to regulate outflow of oil from wells.
- Line drilled holes with pipes, and install all necessary hardware, to prepare new wells.
- Position and prepare truck-mounted derricks at drilling areas specified on field maps.
- Plug observation wells, and restore sites.
- Bolt together pump and engine parts, and connect tanks and flow lines.
- Connect sections of drill pipe, using hand tools and powered wrenches and tongs.
- Assemble and position machines, augers, casing pipes, and other equipment, using hand and power tools.
- Select and attach drill bits and drill rods, adding more rods as hole depths increase, and changing drill bits as needed.
- Operate controls to stabilize machines and to position and align drills.
- Start, stop, and control drilling speed of machines and insertion of casings into holes.
- Regulate air pressure, rotary speed, and downward pressure, according to the type of rock or concrete being drilled.
- Drive or guide truck-mounted equipment into position, level and stabilize rigs, and extend telescoping derricks.
- Operate machines to flush earth cuttings or to blow dust from holes.
- Verify depths and alignments of boring positions.
- Perform routine maintenance and upgrade work on machines and equipment, such as replacing parts, building up drill bits, and lubricating machinery.
- Select the appropriate drill for the job, using knowledge of rock or soil conditions.
- Document geological formations encountered during work.
- Drive trucks, tractors, or truck-mounted drills to and from work sites.
- Record drilling progress and geological data.
- Retrieve lost equipment from bore holes, using retrieval tools and equipment.
- Fabricate well casings.
- Pour water into wells, or pump water or slush into wells to cool drill bits and to remove drillings.
- Create and lay out designs for drill and blast patterns.
- Place and install screens, casings, pumps, and other well fixtures to develop wells.
- Operate water-well drilling rigs and other equipment to drill, bore, and dig for water wells or for environmental assessment purposes.
- Review client requirements and proposed locations for drilling operations to determine feasibility, and to determine cost estimates.
- Drill or bore holes in rock for blasting, grouting, anchoring, or building foundations.
- Perform pumping tests to assess well performance.
- Disinfect, reconstruct, and redevelop contaminated wells and water pumping systems, and clean and disinfect new wells in preparation for use.
- Design well pumping systems.
- Signal crane operators to move equipment.
- Withdraw drill rods from holes, and extract core samples.
- Inspect core samples to determine nature of strata, or take samples to laboratories for analysis.
- Retract augers to force discharge dirt from holes.
- Monitor drilling operations, by checking gauges and listening to equipment to assess drilling conditions and to determine the need to adjust drilling or alter equipment.
- Assemble and position machines, augers, casing pipes, and other equipment, using hand and power tools.
- Select and attach drill bits and drill rods, adding more rods as hole depths increase, and changing drill bits as needed.
- Install gas burners to convert furnaces from wood, coal, or oil.
- Measure, cut, thread and assemble new pipe, placing the assembled pipe in hangers or other supports.
- Cut or drill holes in walls or floors to accommodate the passage of pipes.
- Perform rough-ins, repair and replace fixtures and water heaters, and locate, repair, or remove leaking or broken pipes.
- Assist pipe fitters in the layout, assembly, and installation of piping for air, ammonia, gas, and water systems.
- Cut pipe and lift up to fitters.
- Fit or assist in fitting valves, couplings, or assemblies to tanks, pumps, or systems, using hand tools.
- Requisition tools and equipment, select type and size of pipe, and collect and transport materials and equipment to work site.
- Mount brackets and hangers on walls and ceilings to hold pipes, and set sleeves or inserts to provide support for pipes.
- Excavate and grade ditches, and lay and join pipe for water and sewer service.
- Disassemble and remove damaged or worn pipe.
- Clean shop, work area, and machines, using solvent and rags.
- Fill pipes with sand or resin to prevent distortion, and hold pipes during bending and installation.
- Immerse pipe in chemical solution to remove dirt, oil, and scale.
- Clean and renew steam traps.
- Install gas burners to convert furnaces from wood, coal, or oil.
- Install equipment, such as instrumentation, test equipment, engines, or aftermarket products, to ensure proper interfaces.
- Document test results, using cameras, spreadsheets, documents, or other tools.
- Set up mechanical, hydraulic, or electric test equipment in accordance with engineering specifications, standards, or test procedures.
- Read and interpret blueprints, schematics, work specifications, drawings, or charts.
- Inspect or test parts to determine nature or cause of defects or malfunctions.
- Monitor computer-controlled test equipment, according to written or verbal instructions.
- Analyze test data for automotive systems, subsystems, or component parts.
- Perform or execute manual or automated tests of automotive system or component performance, efficiency, or durability.
- Maintain test equipment in operational condition by performing routine maintenance or making minor repairs or adjustments as needed.
- Analyze performance of vehicles or components that have been redesigned to increase fuel efficiency, such as camless or dual-clutch engines or alternative types of air-conditioning systems.
- Improve fuel efficiency by testing vehicles or components that use lighter materials, such as aluminum, magnesium alloy, or plastic.
- Fabricate new or modify existing prototype components or fixtures.
- Order new test equipment, supplies, or replacement parts.
- Recommend product or component design improvements, based on test data or observations.
- Recommend tests or testing conditions in accordance with designs, customer requirements, or industry standards to ensure test validity.
- Test performance of vehicles that use alternative fuels, such as alcohol blends, natural gas, liquefied petroleum gas, biodiesel, nano diesel, or alternative power methods, such as solar energy or hydrogen fuel cells.
- Participate in research or testing of computerized automotive applications, such as telemetrics, intelligent transportation systems, artificial intelligence, or automatic control.
- Build instrumentation or laboratory test equipment for special purposes.
- Install equipment, such as instrumentation, test equipment, engines, or aftermarket products, to ensure proper interfaces.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Maintain equipment, making repairs or modifications when necessary.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Transport prefabricated parts to construction sites for assembly and installation.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
- Hire, train, or supervise new employees or apprentices.
- Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, using calculators, scribes, dividers, squares, or rulers.
- Fabricate or alter parts at construction sites, using shears, hammers, punches, or drills.
- Determine project requirements, such as scope, assembly sequences, or required methods or materials, using blueprints, drawings, or written or verbal instructions.
- Maneuver completed roofing units into position for installation.
- Select gauges or types of sheet metal or nonmetallic material, according to product specifications.
- Shape metal material over anvils, blocks, or other forms, using hand tools.
- Trim, file, grind, deburr, buff, or smooth surfaces, seams, or joints of assembled parts, using hand tools or portable power tools.
- Inspect individual parts, assemblies, or installations, using measuring instruments, such as calipers, scales, or micrometers.
- Convert blueprints into shop drawings to be followed in the construction or assembly of sheet metal products.
- Verify that heating, ventilating, and air conditioning (HVAC) systems are designed, installed, and calibrated in accordance with green certification standards, such as those of Leadership in Energy and Environmental Design (LEED).
- Perform building commissioning activities by completing mechanical inspections of a building's water, lighting, or heating, ventilating, and air conditioning (HVAC) systems.
- Fasten roof panel edges or machine-made moldings to structures by nailing or welding.
- Finish parts, using hacksaws or hand, rotary, or squaring shears.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Install, test, or maintain radio frequency identification device (RFID) systems.
- Identify operational requirements for new systems to inform selection of technological solutions.
- Integrate tags, readers, or software in radio frequency identification device (RFID) designs.
- Perform systems analysis or programming of radio frequency identification device (RFID) technology.
- Test radio frequency identification device (RFID) software to ensure proper functioning.
- Select appropriate radio frequency identification device (RFID) tags and determine placement locations.
- Perform site analyses to determine system configurations, processes to be impacted, or on-site obstacles to technology implementation.
- Perform acceptance testing on newly installed or updated systems.
- Determine means of integrating radio frequency identification device (RFID) into other applications.
- Provide technical support for radio frequency identification device (RFID) technology.
- Collect data about existing client hardware, software, networking, or key business processes to inform implementation of radio frequency identification device (RFID) technology.
- Test tags or labels to ensure readability.
- Determine usefulness of new radio frequency identification device (RFID) technologies.
- Verify compliance of developed applications with architectural standards and established practices.
- Train users in details of system operation.
- Develop process flows, work instructions, or standard operating procedures for radio frequency identification device (RFID) systems.
- Read current literature, attend meetings or conferences, or talk with colleagues to stay abreast of industry research about new technologies.
- Document equipment or process details of radio frequency identification device (RFID) technology.
- Define and compare possible radio frequency identification device (RFID) solutions to inform selection for specific projects.
- Create simulations or models of radio frequency identification device (RFID) systems to provide information for selection and configuration.
- Analyze radio frequency identification device (RFID)-related supply chain data.
- Install, test, or maintain radio frequency identification device (RFID) systems.
- Engineer, install, maintain, or repair security systems, programmable logic controls, or other security-related electronic systems.
- Assess the nature and level of physical security threats so that the scope of the problem can be determined.
- Respond to emergency situations on an on-call basis.
- Recommend improvements in security systems or procedures.
- Perform risk analyses so that appropriate countermeasures can be developed.
- Inspect physical security design features, installations, or programs to ensure compliance with applicable standards or regulations.
- Conduct security audits to identify potential vulnerabilities related to physical security or staff safety.
- Design security policies, programs, or practices to ensure adequate security relating to alarm response, access card use, and other security needs.
- Test security measures for final acceptance and implement or provide procedures for ongoing monitoring and evaluation of the measures.
- Design, implement, or establish requirements for security systems, video surveillance, motion detection, or closed-circuit television systems to ensure proper installation and operation.
- Prepare, maintain, or update security procedures, security system drawings, or related documentation.
- Prepare documentation for case reports or court proceedings.
- Develop conceptual designs of security systems.
- Train personnel in security procedures or use of security equipment.
- Review design drawings or technical documents for completeness, correctness, or appropriateness.
- Provide system design and integration recommendations.
- Monitor the work of contractors in the design, construction, and startup phases of security systems.
- Budget and schedule security design work.
- Inspect fire, intruder detection, or other security systems.
- Develop or review specifications for design or construction of security systems.
- Interview witnesses or suspects to identify persons responsible for security breaches or to establish losses, pursue prosecutions, or obtain restitution.
- Outline system security criteria for pre-bid meetings with clients and companies to ensure comprehensiveness and appropriateness for implementation.
- Monitor tapes or digital recordings to identify the source of losses.
- Prepare written reports or presentations on findings and recommendations.
- Engineer, install, maintain, or repair security systems, programmable logic controls, or other security-related electronic systems.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
- Follow established safety rules and regulations and maintain a safe and clean environment.
- Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
- Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue.
- Study specifications in blueprints, sketches, or building plans to prepare project layout and determine dimensions and materials required.
- Shape or cut materials to specified measurements, using hand tools, machines, or power saws.
- Verify trueness of structure, using plumb bob and level.
- Inspect ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.
- Erect scaffolding or ladders for assembling structures above ground level.
- Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.
- Maintain records, document actions, and present written progress reports.
- Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.
- Maintain job records and schedule work crew.
- Anchor and brace forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.
- Bore boltholes in timber, masonry or concrete walls, using power drill.
- Install rough door and window frames, subflooring, fixtures, or temporary supports in structures undergoing construction or repair.
- Dig or direct digging of post holes and set poles to support structures.
- Cover subfloors with building paper to keep out moisture and lay hardwood, parquet, or wood-strip-block floors by nailing floors to subfloor or cementing them to mastic or asphalt base.
- Construct forms or chutes for pouring concrete.
- Arrange for subcontractors to deal with special areas, such as heating or electrical wiring work.
- Build or repair cabinets, doors, frameworks, floors, or other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, or power tools.
- Finish surfaces of woodwork or wallboard in houses or buildings, using paint, hand tools, or paneling.
- Select and order lumber or other required materials.
- Work with or remove hazardous material.
- Fill cracks or other defects in plaster or plasterboard and sand patch, using patching plaster, trowel, and sanding tool.
- Prepare cost estimates for clients or employers.
- Perform minor plumbing, welding, or concrete mixing work.
- Apply shock-absorbing, sound-deadening, or decorative paneling to ceilings or walls.
- Examine structural timbers and supports to detect decay, and replace timbers as required, using hand tools, nuts, and bolts.
- Use drones for site surveying and to inspect hard-to-reach areas of a structure.
- Build sleds from logs and timbers for use in hauling camp buildings and machinery through wooded areas.
