- Remove upholstery, accessories, electrical window-and-seat-operating equipment, and trim to gain access to vehicle bodies and fenders.
Occupations with related tasks Save Table: XLSX CSV
- Remove moldings, clips, windshield wipers, screws, bolts, and inside A-pillar moldings and lower headliners in preparation for installation or repair work.
- Hold cut or uneven edges of glass against automated abrasive belts to shape or smooth edges.
- Cut flat safety glass according to specified patterns or perform precision pattern making and glass cutting to custom fit replacement windows.
- Prime all scratches on pinchwelds with primer and allow to dry.
- Remove all dirt, foreign matter, and loose glass from damaged areas, apply primer along windshield or window edges, and allow primer to dry.
- Allow all glass parts installed with urethane ample time to cure, taking temperature and humidity into account.
- Apply a bead of urethane around the perimeter of each pinchweld and dress the remaining urethane on the pinchwelds so that it is of uniform level and thickness.
- Select appropriate tools, safety equipment, and parts, according to job requirements.
- Install replacement glass in vehicles.
- Obtain windshields or windows for specific automobile makes and models from stock and examine them for defects prior to installation.
- Check for and remove moisture or contamination in damaged areas and keep areas dry until repairs are complete.
- Replace all moldings, clips, windshield wipers, or other parts that were removed prior to glass replacement or repair.
- Remove broken or damaged glass windshields or window glass from motor vehicles, using hand tools to remove screws from frames holding glass.
- Install, repair, or replace safety glass and related materials, such as back glass heating elements, on vehicles or equipment.
- Cool or warm glass in the event of temperature extremes.
- Replace or adjust motorized or manual window-raising mechanisms.
- Install new foam dams on pinchwelds, if required.
- Install rubber channeling strips around edges of glass or frames to weatherproof windows or to prevent rattling.
- Remove moldings, clips, windshield wipers, screws, bolts, and inside A-pillar moldings and lower headliners in preparation for installation or repair work.
- Hold cut or uneven edges of glass against automated abrasive belts to shape or smooth edges.
- Cut flat safety glass according to specified patterns or perform precision pattern making and glass cutting to custom fit replacement windows.
- Cut new drumheads from animal skins, using scissors, and soak drumheads in water to make them pliable.
- Cut out sections around cracks on percussion instruments to prevent cracks from advancing, using shears or grinding wheels.
- Disassemble instruments and parts for repair and adjustment.
- Remove drumheads by removing tension rods with drum keys and cutting tools.
- Remove material from bars of percussion instruments to obtain specified tones, using bandsaws, sanding machines, machine grinders, or hand files and scrapers.
- Play instruments to evaluate their sound quality and to locate any defects.
- Adjust string tensions to tune instruments, using hand tools and electronic tuning devices.
- Reassemble instruments following repair, using hand tools and power tools and glue, hair, yarn, resin, or clamps, and lubricate instruments as necessary.
- Repair or replace musical instrument parts and components, such as strings, bridges, felts, and keys, using hand and power tools.
- Inspect instruments to locate defects, and to determine their value or the level of restoration required.
- Compare instrument pitches with tuning tool pitches to tune instruments.
- String instruments, and adjust trusses and bridges of instruments to obtain specified string tensions and heights.
- Polish instruments, using rags and polishing compounds, buffing wheels, or burnishing tools.
- Repair cracks in wood or metal instruments, using pinning wire, lathes, fillers, clamps, or soldering irons.
- Mix and measure glue that will be used for instrument repair.
- Shape old parts and replacement parts to improve tone or intonation, using hand tools, lathes, or soldering irons.
- Refinish instruments to protect and decorate them, using hand tools, buffing tools, and varnish.
- Make wood replacement parts, using woodworking machines and hand tools.
- Align pads and keys on reed or wind instruments.
- Solder posts and parts to hold them in their proper places.
- Remove dents and burrs from metal instruments, using mallets and burnishing tools.
- Test tubes and pickups in electronic amplifier units, and solder parts and connections as necessary.
- Adjust felt hammers on pianos to increase tonal mellowness or brilliance, using sanding paddles, lacquer, or needles.
- Remove irregularities from tuning pins, strings, and hammers of pianos, using wood blocks or filing tools.
- Strike wood, fiberglass, or metal bars of instruments, and use tuned blocks, stroboscopes, or electronic tuners to evaluate tones made by instruments.
- Wash metal instruments in lacquer-stripping and cyanide solutions to remove lacquer and tarnish.
- Assemble and install new pipe organs and pianos in buildings.
- Refinish and polish piano cabinets or cases to prepare them for sale.
- Deliver pianos to purchasers or to locations of their use.
- Place rim hoops back onto drum shells to allow new drumheads to dry and become taut.
- Solder or weld frames of mallet instruments and metal drum parts.
- Repair breaks in percussion instruments, such as drums and cymbals, using drill presses, power saws, glue, clamps, grinding wheels, or other hand tools.
- Assemble bars onto percussion instruments.
- Stretch drumheads over rim hoops and tuck them around and under the hoops, using hand tucking tools.
- Clean, sand, and paint parts of percussion instruments to maintain their condition.
- File metal reeds until their pitches correspond with standard tuning bar pitches.
- Replace xylophone bars and wheels.
- Cut new drumheads from animal skins, using scissors, and soak drumheads in water to make them pliable.
- Cut out sections around cracks on percussion instruments to prevent cracks from advancing, using shears or grinding wheels.
- Disassemble instruments and parts for repair and adjustment.
- Remove drumheads by removing tension rods with drum keys and cutting tools.
- Remove material from bars of percussion instruments to obtain specified tones, using bandsaws, sanding machines, machine grinders, or hand files and scrapers.
- Trim trees that could be hazardous to the functioning of cables or wires.
- Cut and peel lead sheathing and insulation from defective or newly installed cables and conduits prior to splicing.
- Adhere to safety practices and procedures, such as checking equipment regularly and erecting barriers around work areas.
- Drive vehicles equipped with tools and materials to job sites.
- Open switches or attach grounding devices to remove electrical hazards from disturbed or fallen lines or to facilitate repairs.
- Climb poles or use truck-mounted buckets to access equipment.
- Install, maintain, and repair electrical distribution and transmission systems, including conduits, cables, wires, and related equipment, such as transformers, circuit breakers, and switches.
- Inspect and test power lines and auxiliary equipment to locate and identify problems, using reading and testing instruments.
- Coordinate work assignment preparation and completion with other workers.
- Replace or straighten damaged poles.
- String wire conductors and cables between poles, towers, trenches, pylons, and buildings, setting lines in place and using winches to adjust tension.
- Attach cross-arms, insulators, and auxiliary equipment to poles prior to installing them.
- Dig holes, using augers, and set poles, using cranes and power equipment.
- Travel in trucks, helicopters, and airplanes to inspect lines for freedom from obstruction and adequacy of insulation.
- Identify defective sectionalizing devices, circuit breakers, fuses, voltage regulators, transformers, switches, relays, or wiring, using wiring diagrams and electrical-testing instruments.
- Install watt-hour meters and connect service drops between power lines and consumers' facilities.
- Test conductors, according to electrical diagrams and specifications, to identify corresponding conductors and to prevent incorrect connections.
- Place insulating or fireproofing materials over conductors and joints.
- Splice or solder cables together or to overhead transmission lines, customer service lines, or street light lines, using hand tools, epoxies, or specialized equipment.
- Pull up cable by hand from large reels mounted on trucks.
- Lay underground cable directly in trenches, or string it through conduit running through the trenches.
- Cut trenches for laying underground cables, using trenchers and cable plows.
- Clean, tin, and splice corresponding conductors by twisting ends together or by joining ends with metal clamps and soldering connections.
- Trim trees that could be hazardous to the functioning of cables or wires.
- Cut and peel lead sheathing and insulation from defective or newly installed cables and conduits prior to splicing.
- Cut new or duplicate keys, using key cutting machines.
- Disassemble mechanical or electrical locking devices, and repair or replace worn tumblers, springs, and other parts, using hand tools.
- Move picklocks in cylinders to open door locks without keys.
- Unlock cars and other vehicles.
- Cut new or duplicate keys, using impressions or code key machines.
- Open safe locks by drilling.
- Install door hardware, such as locks and closers.
- Insert new or repaired tumblers into locks to change combinations.
- Set up and maintain master key systems.
- Keep records of company locks and keys.
- Repair and adjust safes, vault doors, and vault components, using hand tools, lathes, drill presses, and welding and acetylene cutting apparatus.
- Install safes, vault doors, and deposit boxes according to blueprints, using equipment such as power drills, taps, dies, truck cranes, and dollies.
- Install alarm and electronic access systems.
- Remove interior and exterior finishes on safes and vaults, and spray on new finishes.
- Cut new or duplicate keys, using key cutting machines.
- Disassemble mechanical or electrical locking devices, and repair or replace worn tumblers, springs, and other parts, using hand tools.
- Move picklocks in cylinders to open door locks without keys.
- Unlock cars and other vehicles.
- Trim and shape replacement body sections to specified sizes and fits and secure sections in place, using adhesives, hand tools, and power tools.
- Remove or cut out defective parts or drill holes to gain access to internal defects or damage, using drills and punches.
- Disassemble engines and inspect parts, such as turbine blades or cylinders, for corrosion, wear, warping, cracks, and leaks, using precision measuring instruments, x-rays, and magnetic inspection equipment.
- Remove, inspect, repair, and install in-flight refueling stores and external fuel tanks.
- Examine and inspect aircraft components, including landing gear, hydraulic systems, and deicers to locate cracks, breaks, leaks, or other problems.
- Conduct routine and special inspections as required by regulations.
- Inspect completed work to certify that maintenance meets standards and that aircraft are ready for operation.
- Read and interpret maintenance manuals, service bulletins, and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.
- Maintain repair logs, documenting all preventive and corrective aircraft maintenance.
- Modify aircraft structures, space vehicles, systems, or components, following drawings, schematics, charts, engineering orders, and technical publications.
- Inspect airframes for wear or other defects.
- Measure parts for wear, using precision instruments.
- Obtain fuel and oil samples and check them for contamination.
- Maintain, repair, and rebuild aircraft structures, functional components, and parts, such as wings and fuselage, rigging, hydraulic units, oxygen systems, fuel systems, electrical systems, gaskets, or seals.
- Replace or repair worn, defective, or damaged components, using hand tools, gauges, and testing equipment.
- Read and interpret pilots' descriptions of problems to diagnose causes.
- Test operation of engines and other systems, using test equipment, such as ignition analyzers, compression checkers, distributor timers, or ammeters.
- Measure the tension of control cables.
- Spread plastic film over areas to be repaired to prevent damage to surrounding areas.
- Remove or install aircraft engines, using hoists or forklift trucks.
- Assemble and install electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools.
- Locate and mark dimensions and reference lines on defective or replacement parts, using templates, scribes, compasses, and steel rules.
- Fabricate defective sections or parts, using metal fabricating machines, saws, brakes, shears, and grinders.
- Reassemble engines following repair or inspection and reinstall engines in aircraft.
- Service and maintain aircraft and related apparatus by performing activities such as flushing crankcases, cleaning screens, and or moving parts.
- Clean, refuel, and change oil in line service aircraft.
- Accompany aircraft on flights to make in-flight adjustments and corrections.
- Install and align repaired or replacement parts for subsequent riveting or welding, using clamps and wrenches.
- Inventory and requisition or order supplies, parts, materials, and equipment.
- Clean, strip, prime, and sand structural surfaces and materials to prepare them for bonding.
- Communicate with other workers to coordinate fitting and alignment of heavy parts, or to facilitate processing of repair parts.
- Examine engines through specially designed openings while working from ladders or scaffolds, or use hoists or lifts to remove the entire engine from an aircraft.
- Check for corrosion, distortion, and invisible cracks in the fuselage, wings, and tail, using x-ray and magnetic inspection equipment.
- Cure bonded structures, using portable or stationary curing equipment.
- Listen to operating engines to detect and diagnose malfunctions, such as sticking or burned valves.
- Clean engines, sediment bulk and screens, and carburetors, adjusting carburetor float levels.
- Determine repair limits for engine hot section parts.
- Prepare and paint aircraft surfaces.
- Trim and shape replacement body sections to specified sizes and fits and secure sections in place, using adhesives, hand tools, and power tools.
- Remove or cut out defective parts or drill holes to gain access to internal defects or damage, using drills and punches.
- Disassemble engines and inspect parts, such as turbine blades or cylinders, for corrosion, wear, warping, cracks, and leaks, using precision measuring instruments, x-rays, and magnetic inspection equipment.
- Remove, inspect, repair, and install in-flight refueling stores and external fuel tanks.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Record maintenance information, including test results, material usage, and repairs made.
- Lubricate wearing surfaces of mechanical parts, using oils or other lubricants.
- Calibrate instrumentation, such as meters, gauges, and regulators, for pressure, temperature, flow, and level.
- Install, inspect and test electric meters, relays, and power sources to detect causes of malfunctions and inaccuracies, using hand tools and testing equipment.
- Test valves and regulators for leaks and accurate temperature and pressure settings, using precision testing equipment.
- Record meter readings and installation data on meter cards, work orders, or field service orders, or enter data into hand-held computers.
- Turn meters on or off to establish or close service.
- Shut off service and notify repair crews when major repairs are required, such as the replacement of underground pipes or wiring.
- Install regulators and related equipment such as gas meters, odorization units, and gas pressure telemetering equipment.
- Turn valves to allow measured amounts of air or gas to pass through meters at specified flow rates.
- Report hazardous field situations and damaged or missing meters.
- Vary air pressure flowing into regulators and turn handles to assess functioning of valves and pistons.
- Examine valves or mechanical control device parts for defects, dents, or loose attachments, and mark malfunctioning areas of defective units.
- Mount and install meters and other electric equipment such as time clocks, transformers, and circuit breakers, using electricians' hand tools.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Investigate instances of illegal tapping into service lines.
- Trace and tag meters or house lines.
- Repair electric meters and components, such as transformers and relays, and replace metering devices, dial glasses, and faulty or incorrect wiring, using hand tools.
- Replace defective parts, such as bellows, range springs, and toggle switches, and reassemble units according to blueprints, using cam presses and hand tools.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Measure tolerances of assembled and salvageable parts for conformance to standards or specifications, using gauges, micrometers, and calipers.
- Clean internal compartments and moving parts, using rags and cleaning compounds.
- Reassemble repaired equipment, and solder top, front, and back case panels in place, using soldering guns, power tools, and hand tools.
- Attach air hoses to meter inlets, plug outlets, and observe gauges for pressure losses to test internal seams for leaks.
- Make adjustments to meter components, such as setscrews or timing mechanisms, so that they conform to specifications.
- Recommend and write up specifications for changes in hardware, such as house wiring.
- Clamp regulator units into vises on stages above water tanks, and attach compressed air hoses to intake ports.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Collect money due on delinquent accounts.
- Splice and connect cables from meters or current transformers to pull boxes or switchboards, using hand tools.
- Attach pressurized meters to fixtures which submerge them in water, and observe meters for leaks.
- Advise customers on proper installation of valves or regulators and related equipment.
- Calibrate thermostats for specified temperature or pressure settings.
- Clean plant growth, scale, paint, soil, or rust from meter housings, using wire brushes, scrapers, buffers, sandblasters, or cleaning compounds.
- Connect hoses from provers to meter inlets and outlets, and raise prover bells until prover gauges register zero.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Lift units or parts such as motors or generators, using cranes or chain hoists, or signal crane operators to lift heavy parts or subassemblies.
- Record repairs required, parts used, and labor time.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Lubricate moving parts.
- Read service guides to find information needed to perform repairs.
- Inspect electrical connections, wiring, relays, charging resistance boxes, and storage batteries, following wiring diagrams.
- Scrape and clean units or parts, using cleaning solvents and equipment such as buffing wheels.
- Weld, braze, or solder electrical connections.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Steam-clean polishing and buffing wheels to remove abrasives and bonding materials, and spray, brush, or recoat surfaces as necessary.
- Set machinery for proper performance, using computers.
- Test equipment for overheating, using speed gauges and thermometers.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Maintain stocks of parts.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Solder, wrap, and coat wires to ensure proper insulation.
- Rewire electrical systems, and repair or replace electrical accessories.
- Clean cells, cell assemblies, glassware, leads, electrical connections, and battery poles, using scrapers, steam, water, emery cloths, power grinders, or acid.
- Rewind coils on cores in slots, or make replacement coils, using coil-winding machines.
- Test conditions, fluid levels, and specific gravities of electrolyte cells, using voltmeters, hydrometers, and thermometers.
- Add water or acid to battery cell solutions to obtain specified concentrations.
- Pour compounds into transformer-case terminal openings to seal out moisture.
- Hammer out dents and twists in tools and equipment.
- Drain and filter transformer oil and refill transformers with oil until coils are submerged.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Repair and operate battery-charging equipment.
- Sharpen tools such as saws, picks, shovels, screwdrivers, and scoops, either manually or by using bench grinders and emery wheels.
- Inspect batteries for structural defects such as dented cans, damaged carbon rods and terminals, and defective seals.
- Test battery charges, and replace or recharge batteries as necessary.
- Bolt porcelain insulators to wood parts to assemble hot stools.
- Position and level battery cells, anodes, or cathodes, using hoists or leveling jacks, or signal other workers to perform positioning and leveling.
- Clean, rinse, and dry transformer cases, using boiling water, scrapers, solvents, hoses, and cloths.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Open and close doors, windows, and drawers to test their operation, trimming edges to fit, using jackplanes or drawknives.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Move and set up mobile homes or prefabricated buildings on owners' lots or at mobile home parks.
- Inspect, examine, and test the operation of parts or systems to evaluate operating condition and to determine if repairs are needed.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of plumbing fixtures.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, and diagrams.
- Confer with customers or read work orders to determine the nature and extent of damage to units.
- Install, repair, and replace units, fixtures, appliances, and other items and systems in mobile and modular homes, prefabricated buildings, or travel trailers, using hand tools or power tools.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Repair leaks in plumbing or gas lines, using caulking compounds and plastic or copper pipe.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, and hand tools.
- Connect electrical systems to outside power sources and activate switches to test the operation of appliances and light fixtures.
- Refinish wood surfaces on cabinets, doors, moldings, and floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Open and close doors, windows, and drawers to test their operation, trimming edges to fit, using jackplanes or drawknives.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- Cut and weld metal to repair broken metal parts, fabricate new parts, or assemble new equipment.
- Disassemble machinery or equipment to remove parts and make repairs.
- Repair or maintain the operating condition of industrial production or processing machinery or equipment.
- Repair or replace broken or malfunctioning components of machinery or equipment.
- Clean, lubricate, or adjust parts, equipment, or machinery.
- Reassemble equipment after completion of inspections, testing, or repairs.
- Examine parts for defects, such as breakage or excessive wear.
- Record repairs and maintenance performed.
- Operate newly repaired machinery or equipment to verify the adequacy of repairs.
- Record parts or materials used and order or requisition new parts or materials, as necessary.
- Observe and test the operation of machinery or equipment to diagnose malfunctions, using voltmeters or other testing devices.
- Analyze test results, machine error messages, or information obtained from operators to diagnose equipment problems.
- Study blueprints or manufacturers' manuals to determine correct installation or operation of machinery.
- Enter codes and instructions to program computer-controlled machinery.
- Demonstrate equipment functions and features to machine operators.
- Assign schedules to work crews.
- Cut and weld metal to repair broken metal parts, fabricate new parts, or assemble new equipment.
- Disassemble machinery or equipment to remove parts and make repairs.
- Open and close doors, windows, or drawers to test their operation, trimming edges to fit, as necessary.
- Remove damaged exterior panels, and repair and replace structural frame members.
- Explain proper operation of vehicle systems to customers.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, or hand tools.
- Repair plumbing or propane gas lines, using caulking compounds and plastic or copper pipe.
- Confer with customers, read work orders, or examine vehicles needing repair to determine the nature and extent of damage.
- Examine or test operation of parts or systems to ensure completeness of repairs.
- Connect electrical systems to outside power sources, and activate switches to test the operation of appliances or light fixtures.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of toilets or sinks.
- Inspect recreational vehicles to diagnose problems and perform necessary adjustment, repair, or overhaul.
- Inspect, repair, or replace brake systems.
- Diagnose and repair furnace or air conditioning systems.
- Repair leaks with caulking compound or replace pipes, using pipe wrenches.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, or diagrams.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Refinish wood surfaces on cabinets, doors, moldings, or floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Open and close doors, windows, or drawers to test their operation, trimming edges to fit, as necessary.
- Remove damaged exterior panels, and repair and replace structural frame members.
- Cut door stops or angle irons to fit openings.
- Remove or disassemble defective automatic mechanical door closers, using hand tools.
- Wind large springs with upward motion of arm.
- Adjust doors to open or close with the correct amount of effort, or make simple adjustments to electric openers.
- Carry springs to tops of doors, using ladders or scaffolding, and attach springs to tracks to install spring systems.
- Repair or replace worn or broken door parts, using hand tools.
- Complete required paperwork, such as work orders, according to services performed or required.
- Fasten angle iron back-hangers to ceilings and tracks, using fasteners or welding equipment.
- Collect payment upon job completion.
- Install door frames, rails, steel rolling curtains, electronic-eye mechanisms, or electric door openers and closers, using power tools, hand tools, and electronic test equipment.
- Inspect job sites, assessing headroom, side room, or other conditions to determine appropriateness of door for a given location.
- Assemble and fasten tracks to structures or bucks, using impact wrenches or welding equipment.
- Set doors into place or stack hardware sections into openings after rail or track installation.
- Operate lifts, winches, or chain falls to move heavy curtain doors.
- Fabricate replacements for worn or broken parts, using welders, lathes, drill presses, or shaping or milling machines.
- Prepare doors for hardware installation, such as drilling holes to install locks.
- Run low voltage wiring on ceiling surfaces, using insulated staples.
- Study blueprints and schematic diagrams to determine appropriate methods of installing or repairing automated door openers.
- Install dock seals, bumpers, or shelters.
- Order replacement springs, sections, or slats.
- Lubricate door closer oil chambers, and pack spindles with leather washers.
- Set in and secure floor treadles for door-activating mechanisms, and connect power packs and electrical panelboards to treadles.
- Cover treadles with carpeting or other floor covering materials, and test systems by operating treadles.
- Bore or cut holes in flooring as required for installation, using hand or power tools.
- Clean door closer parts, using caustic soda, rotary brushes, or grinding wheels.
- Cut door stops or angle irons to fit openings.
- Remove or disassemble defective automatic mechanical door closers, using hand tools.
- Unbolt and remove wheels from vehicles, using lug wrenches or other hand or power tools.
- Separate tubed tires from wheels, using rubber mallets and metal bars or mechanical tire changers.
- Raise vehicles, using hydraulic jacks.
- Remount wheels onto vehicles.
- Place wheels on balancing machines to determine counterweights required to balance wheels.
- Identify tire size and ply and inflate tires accordingly.
- Replace valve stems and remove puncturing objects.
- Hammer required counterweights onto rims of wheels.
- Reassemble tires onto wheels.
- Seal punctures in tubeless tires by inserting adhesive material and expanding rubber plugs into punctures, using hand tools.
- Inspect tire casings for defects, such as holes or tears.
- Locate punctures in tubeless tires by visual inspection or by immersing inflated tires in water baths and observing air bubbles.
- Glue tire patches over ruptures in tire casings, using rubber cement.
- Assist mechanics and perform various mechanical duties, such as changing oil or checking and replacing batteries.
- Rotate tires to different positions on vehicles, using hand tools.
- Clean and tidy up the shop.
- Buff defective areas of inner tubes, using scrapers.
- Order replacements for tires or tubes.
- Inflate inner tubes and immerse them in water to locate leaks.
- Clean sides of whitewall tires.
- Roll new rubber treads, known as camelbacks, over tire casings and mold the semi-raw rubber treads onto the buffed casings.
- Prepare rims and wheel drums for reassembly by scraping, grinding, or sandblasting.
- Apply rubber cement to buffed tire casings prior to vulcanization process.
- Patch tubes with adhesive rubber patches or seal rubber patches to tubes, using hot vulcanizing plates.
- Place tire casings and tread rubber assemblies in tire molds for the vulcanization process and exert pressure to ensure good adhesion.
- Drive automobile or service trucks to industrial sites to provide services or respond to emergency calls.
- Unbolt and remove wheels from vehicles, using lug wrenches or other hand or power tools.
- Separate tubed tires from wheels, using rubber mallets and metal bars or mechanical tire changers.
- Measure, cut, and thread pipe, and connect it to feeder lines and equipment or appliances, using rules and hand tools.
- Disassemble appliances so that problems can be diagnosed and repairs can be made.
- Bill customers for repair work, and collect payment.
- Observe and examine appliances during operation to detect specific malfunctions such as loose parts or leaking fluid.
- Talk to customers or refer to work orders to establish the nature of appliance malfunctions.
- Refer to schematic drawings, product manuals, and troubleshooting guides to diagnose and repair problems.
- Trace electrical circuits, following diagrams, and conduct tests with circuit testers and other equipment to locate shorts and grounds.
- Replace worn and defective parts such as switches, bearings, transmissions, belts, gears, circuit boards, or defective wiring.
- Provide repair cost estimates, and recommend whether appliance repair or replacement is a better choice.
- Respond to emergency calls for problems such as gas leaks.
- Service and repair domestic electrical or gas appliances, such as clothes washers, refrigerators, stoves, and dryers.
- Reassemble units after repairs are made, making adjustments and cleaning and lubricating parts as needed.
- Record maintenance and repair work performed on appliances.
- Test and examine gas pipelines and equipment to locate leaks and faulty connections, and to determine the pressure and flow of gas.
- Light and adjust pilot lights on gas stoves, and examine valves and burners for gas leakage and specified flame.
- Instruct customers regarding operation and care of appliances, and provide information such as emergency service numbers.
- Contact supervisors or offices to receive repair assignments.
- Maintain stocks of parts used in on-site installation, maintenance, and repair of appliances.
- Level refrigerators, adjust doors, and connect water lines to water pipes for ice makers and water dispensers, using hand tools.
- Observe and test operation of appliances following installation, and make any initial installation adjustments that are necessary.
- Set appliance thermostats, and check to ensure that they are functioning properly.
- Install appliances such as refrigerators, washing machines, and stoves.
- Level washing machines and connect hoses to water pipes, using hand tools.
- Clean and reinstall parts.
- Clean, lubricate, and touch up minor defects on newly installed or repaired appliances.
- Conserve, recover, and recycle refrigerants used in cooling systems.
- Install gas pipes and water lines to connect appliances to existing gas lines or plumbing.
- Take measurements to determine if appliances will fit in installation locations, performing minor carpentry work when necessary to ensure proper installation.
- Assemble new or reconditioned appliances.
- Disassemble and reinstall existing kitchen cabinets, or assemble and install prefabricated kitchen cabinets and trim in conjunction with appliance installation.
- Hang steel supports from beams or joists to hold hoses, vents, and gas pipes in place.
- Measure, cut, and thread pipe, and connect it to feeder lines and equipment or appliances, using rules and hand tools.
- Disassemble appliances so that problems can be diagnosed and repairs can be made.
- Remove seats, carpeting, and interiors of doors and add sound-absorbing material in empty spaces, reinstalling interior parts.
- Install equipment and accessories, such as stereos, navigation equipment, communication equipment, and security systems.
- Inspect and test electrical or electronic systems to locate and diagnose malfunctions, using visual inspections and testing instruments, such as oscilloscopes and voltmeters.
- Cut openings and drill holes for fixtures and equipment, using electric drills and routers.
- Splice wires with knives or cutting pliers, and solder connections to fixtures and equipment.
- Diagnose or repair problems with electronic equipment, such as sound, navigation, communication, and security equipment, in motor vehicles.
- Run new speaker and electrical cables.
- Confer with customers to determine the nature of malfunctions.
- Record results of diagnostic tests.
- Estimate costs of repairs, based on parts and labor charges.
- Replace and clean electrical or electronic components.
- Build fiberglass or wooden enclosures for sound components, and fit them to automobile dimensions.
- Remove seats, carpeting, and interiors of doors and add sound-absorbing material in empty spaces, reinstalling interior parts.
- Measure, cut, and install frameworks and conduit to support and connect wiring, control panels, and junction boxes, using hand tools.
- Inspect and test electrical systems and equipment to locate and diagnose malfunctions, using visual inspections, testing devices, and computer software.
- Reassemble and test equipment after repairs.
- Adjust, repair, or replace defective wiring and relays in ignition, lighting, air-conditioning, and safety control systems, using electrician's tools.
- Splice wires with knives or cutting pliers, and solder connections to fixtures, outlets, and equipment.
- Locate and remove or repair circuit defects such as blown fuses or malfunctioning transistors.
- Maintain equipment service records.
- Refer to schematics and manufacturers' specifications that show connections and provide instructions on how to locate problems.
- Install fixtures, outlets, terminal boards, switches, and wall boxes, using hand tools.
- Install new fuses, electrical cables, or power sources as required.
- Cut openings and drill holes for fixtures, outlet boxes, and fuse holders, using electric drills and routers.
- Confer with customers to determine the nature of malfunctions.
- Install electrical equipment such as air-conditioning, heating, or ignition systems and components such as generator brushes and commutators, using hand tools.
- Repair or rebuild equipment such as starters, generators, distributors, or door controls, using electrician's tools.
- Estimate costs of repairs based on parts and labor requirements.
- Measure, cut, and install frameworks and conduit to support and connect wiring, control panels, and junction boxes, using hand tools.
- Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.
- Reline or repair ladles and pouring spouts with refractory clay, using trowels.
- Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.
- Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.
- Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.
- Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.
- Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.
- Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.
- Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.
- Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.
- Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.
- Dump and tamp clay in molds, using tamping tools.
- Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.
- Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.
- Install preformed metal scaffolding in interiors of cupolas, using hand tools.
- Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.
- Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.
- Measure, cut, thread, or bend pipe or tubing, using pipe fitter's tools.
- Test electrical circuits or components for continuity, using electrical test equipment.
- Comply with all applicable standards, policies, or procedures, such as safety procedures or the maintenance of a clean work area.
- Study blueprints, design specifications, or manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.
- Discuss heating or cooling system malfunctions with users to isolate problems or to verify that repairs corrected malfunctions.
- Connect heating or air conditioning equipment to fuel, water, or refrigerant source to form complete circuit.
- Adjust system controls to settings recommended by manufacturer to balance system.
- Recommend, develop, or perform preventive or general maintenance procedures, such as cleaning, power-washing, or vacuuming equipment, oiling parts, or changing filters.
- Inspect and test systems to verify system compliance with plans and specifications or to detect and locate malfunctions.
- Repair or replace defective equipment, components, or wiring.
- Install or repair self-contained ground source heat pumps or hybrid ground or air source heat pumps to minimize carbon-based energy consumption and reduce carbon emissions.
- Install, connect, or adjust thermostats, humidistats, or timers.
- Install auxiliary components to heating or cooling equipment, such as expansion or discharge valves, air ducts, pipes, blowers, dampers, flues, or stokers.
- Braze or solder parts to repair defective joints and leaks.
- Lay out and connect electrical wiring between controls and equipment, according to wiring diagrams, using electrician's hand tools.
- Perform mechanical overhauls and refrigerant reclaiming.
- Install expansion and control valves, using acetylene torches and wrenches.
- Mount compressor, condenser, and other components in specified locations on frames, using hand tools and acetylene welding equipment.
- Install dehumidifiers or related equipment for spaces that require cool, dry air to operate efficiently, such as computer rooms.
- Record and report time, materials, faults, deficiencies, or other unusual occurrences on work orders.
- Keep records of repairs and replacements made and causes of malfunctions.
- Cut or drill holes in floors, walls, or roof to install equipment, using power saws or drills.
- Estimate, order, pick up, deliver, and install materials and supplies needed to maintain equipment in good working condition.
- Schedule work with customers and initiate work orders, house requisitions, and orders from stock.
- Supervise and instruct assistants.
- Lay out reference points for installation of structural and functional components, using measuring instruments.
- Lift and align components into position, using hoist or block and tackle.
- Install or repair air purification systems, such as specialized filters or ultraviolet (UV) light purification systems.
- Repair or service heating, ventilating, and air conditioning (HVAC) systems to improve efficiency, such as by changing filters, cleaning ducts, and refilling non-toxic refrigerants.
- Test pipes, lines, components, and connections for leaks.
- Measure, cut, thread, or bend pipe or tubing, using pipe fitter's tools.
