- Cut and tape plastic separating film to outside repair areas to avoid damaging surrounding surfaces during repair procedure and remove tape and wash surfaces after repairs are complete.
Occupations with related tasks Save Table: XLSX CSV
- Hold cut or uneven edges of glass against automated abrasive belts to shape or smooth edges.
- Cut flat safety glass according to specified patterns or perform precision pattern making and glass cutting to custom fit replacement windows.
- Prime all scratches on pinchwelds with primer and allow to dry.
- Remove all dirt, foreign matter, and loose glass from damaged areas, apply primer along windshield or window edges, and allow primer to dry.
- Allow all glass parts installed with urethane ample time to cure, taking temperature and humidity into account.
- Apply a bead of urethane around the perimeter of each pinchweld and dress the remaining urethane on the pinchwelds so that it is of uniform level and thickness.
- Select appropriate tools, safety equipment, and parts, according to job requirements.
- Install replacement glass in vehicles.
- Obtain windshields or windows for specific automobile makes and models from stock and examine them for defects prior to installation.
- Check for and remove moisture or contamination in damaged areas and keep areas dry until repairs are complete.
- Replace all moldings, clips, windshield wipers, or other parts that were removed prior to glass replacement or repair.
- Remove broken or damaged glass windshields or window glass from motor vehicles, using hand tools to remove screws from frames holding glass.
- Remove moldings, clips, windshield wipers, screws, bolts, and inside A-pillar moldings and lower headliners in preparation for installation or repair work.
- Install, repair, or replace safety glass and related materials, such as back glass heating elements, on vehicles or equipment.
- Cool or warm glass in the event of temperature extremes.
- Replace or adjust motorized or manual window-raising mechanisms.
- Install new foam dams on pinchwelds, if required.
- Install rubber channeling strips around edges of glass or frames to weatherproof windows or to prevent rattling.
- Hold cut or uneven edges of glass against automated abrasive belts to shape or smooth edges.
- Cut flat safety glass according to specified patterns or perform precision pattern making and glass cutting to custom fit replacement windows.
- Trim trees that could be hazardous to the functioning of cables or wires.
- Cut and peel lead sheathing and insulation from defective or newly installed cables and conduits prior to splicing.
- Adhere to safety practices and procedures, such as checking equipment regularly and erecting barriers around work areas.
- Drive vehicles equipped with tools and materials to job sites.
- Open switches or attach grounding devices to remove electrical hazards from disturbed or fallen lines or to facilitate repairs.
- Climb poles or use truck-mounted buckets to access equipment.
- Install, maintain, and repair electrical distribution and transmission systems, including conduits, cables, wires, and related equipment, such as transformers, circuit breakers, and switches.
- Inspect and test power lines and auxiliary equipment to locate and identify problems, using reading and testing instruments.
- Coordinate work assignment preparation and completion with other workers.
- Replace or straighten damaged poles.
- String wire conductors and cables between poles, towers, trenches, pylons, and buildings, setting lines in place and using winches to adjust tension.
- Attach cross-arms, insulators, and auxiliary equipment to poles prior to installing them.
- Dig holes, using augers, and set poles, using cranes and power equipment.
- Travel in trucks, helicopters, and airplanes to inspect lines for freedom from obstruction and adequacy of insulation.
- Identify defective sectionalizing devices, circuit breakers, fuses, voltage regulators, transformers, switches, relays, or wiring, using wiring diagrams and electrical-testing instruments.
- Install watt-hour meters and connect service drops between power lines and consumers' facilities.
- Test conductors, according to electrical diagrams and specifications, to identify corresponding conductors and to prevent incorrect connections.
- Place insulating or fireproofing materials over conductors and joints.
- Splice or solder cables together or to overhead transmission lines, customer service lines, or street light lines, using hand tools, epoxies, or specialized equipment.
- Pull up cable by hand from large reels mounted on trucks.
- Lay underground cable directly in trenches, or string it through conduit running through the trenches.
- Cut trenches for laying underground cables, using trenchers and cable plows.
- Clean, tin, and splice corresponding conductors by twisting ends together or by joining ends with metal clamps and soldering connections.
- Trim trees that could be hazardous to the functioning of cables or wires.
- Cut and peel lead sheathing and insulation from defective or newly installed cables and conduits prior to splicing.
- Cut new drumheads from animal skins, using scissors, and soak drumheads in water to make them pliable.
- Cut out sections around cracks on percussion instruments to prevent cracks from advancing, using shears or grinding wheels.
- Play instruments to evaluate their sound quality and to locate any defects.
- Adjust string tensions to tune instruments, using hand tools and electronic tuning devices.
- Reassemble instruments following repair, using hand tools and power tools and glue, hair, yarn, resin, or clamps, and lubricate instruments as necessary.
- Disassemble instruments and parts for repair and adjustment.
- Repair or replace musical instrument parts and components, such as strings, bridges, felts, and keys, using hand and power tools.
- Inspect instruments to locate defects, and to determine their value or the level of restoration required.
- Compare instrument pitches with tuning tool pitches to tune instruments.
- String instruments, and adjust trusses and bridges of instruments to obtain specified string tensions and heights.
- Polish instruments, using rags and polishing compounds, buffing wheels, or burnishing tools.
- Repair cracks in wood or metal instruments, using pinning wire, lathes, fillers, clamps, or soldering irons.
- Mix and measure glue that will be used for instrument repair.
- Shape old parts and replacement parts to improve tone or intonation, using hand tools, lathes, or soldering irons.
- Refinish instruments to protect and decorate them, using hand tools, buffing tools, and varnish.
- Make wood replacement parts, using woodworking machines and hand tools.
- Align pads and keys on reed or wind instruments.
- Solder posts and parts to hold them in their proper places.
- Remove dents and burrs from metal instruments, using mallets and burnishing tools.
- Test tubes and pickups in electronic amplifier units, and solder parts and connections as necessary.
- Adjust felt hammers on pianos to increase tonal mellowness or brilliance, using sanding paddles, lacquer, or needles.
- Remove irregularities from tuning pins, strings, and hammers of pianos, using wood blocks or filing tools.
- Strike wood, fiberglass, or metal bars of instruments, and use tuned blocks, stroboscopes, or electronic tuners to evaluate tones made by instruments.
- Wash metal instruments in lacquer-stripping and cyanide solutions to remove lacquer and tarnish.
- Assemble and install new pipe organs and pianos in buildings.
- Refinish and polish piano cabinets or cases to prepare them for sale.
- Deliver pianos to purchasers or to locations of their use.
- Remove drumheads by removing tension rods with drum keys and cutting tools.
- Place rim hoops back onto drum shells to allow new drumheads to dry and become taut.
- Solder or weld frames of mallet instruments and metal drum parts.
- Repair breaks in percussion instruments, such as drums and cymbals, using drill presses, power saws, glue, clamps, grinding wheels, or other hand tools.
- Assemble bars onto percussion instruments.
- Stretch drumheads over rim hoops and tuck them around and under the hoops, using hand tucking tools.
- Clean, sand, and paint parts of percussion instruments to maintain their condition.
- File metal reeds until their pitches correspond with standard tuning bar pitches.
- Replace xylophone bars and wheels.
- Remove material from bars of percussion instruments to obtain specified tones, using bandsaws, sanding machines, machine grinders, or hand files and scrapers.
- Cut new drumheads from animal skins, using scissors, and soak drumheads in water to make them pliable.
- Cut out sections around cracks on percussion instruments to prevent cracks from advancing, using shears or grinding wheels.
- Spread plastic film over areas to be repaired to prevent damage to surrounding areas.
- Trim and shape replacement body sections to specified sizes and fits and secure sections in place, using adhesives, hand tools, and power tools.
- Examine and inspect aircraft components, including landing gear, hydraulic systems, and deicers to locate cracks, breaks, leaks, or other problems.
- Conduct routine and special inspections as required by regulations.
- Inspect completed work to certify that maintenance meets standards and that aircraft are ready for operation.
- Read and interpret maintenance manuals, service bulletins, and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.
- Maintain repair logs, documenting all preventive and corrective aircraft maintenance.
- Modify aircraft structures, space vehicles, systems, or components, following drawings, schematics, charts, engineering orders, and technical publications.
- Inspect airframes for wear or other defects.
- Measure parts for wear, using precision instruments.
- Obtain fuel and oil samples and check them for contamination.
- Maintain, repair, and rebuild aircraft structures, functional components, and parts, such as wings and fuselage, rigging, hydraulic units, oxygen systems, fuel systems, electrical systems, gaskets, or seals.
- Replace or repair worn, defective, or damaged components, using hand tools, gauges, and testing equipment.
- Read and interpret pilots' descriptions of problems to diagnose causes.
- Test operation of engines and other systems, using test equipment, such as ignition analyzers, compression checkers, distributor timers, or ammeters.
- Measure the tension of control cables.
- Remove or install aircraft engines, using hoists or forklift trucks.
- Assemble and install electrical, plumbing, mechanical, hydraulic, and structural components and accessories, using hand or power tools.
- Locate and mark dimensions and reference lines on defective or replacement parts, using templates, scribes, compasses, and steel rules.
- Fabricate defective sections or parts, using metal fabricating machines, saws, brakes, shears, and grinders.
- Reassemble engines following repair or inspection and reinstall engines in aircraft.
- Service and maintain aircraft and related apparatus by performing activities such as flushing crankcases, cleaning screens, and or moving parts.
- Clean, refuel, and change oil in line service aircraft.
- Accompany aircraft on flights to make in-flight adjustments and corrections.
- Remove or cut out defective parts or drill holes to gain access to internal defects or damage, using drills and punches.
- Install and align repaired or replacement parts for subsequent riveting or welding, using clamps and wrenches.
- Inventory and requisition or order supplies, parts, materials, and equipment.
- Clean, strip, prime, and sand structural surfaces and materials to prepare them for bonding.
- Communicate with other workers to coordinate fitting and alignment of heavy parts, or to facilitate processing of repair parts.
- Examine engines through specially designed openings while working from ladders or scaffolds, or use hoists or lifts to remove the entire engine from an aircraft.
- Check for corrosion, distortion, and invisible cracks in the fuselage, wings, and tail, using x-ray and magnetic inspection equipment.
- Disassemble engines and inspect parts, such as turbine blades or cylinders, for corrosion, wear, warping, cracks, and leaks, using precision measuring instruments, x-rays, and magnetic inspection equipment.
- Cure bonded structures, using portable or stationary curing equipment.
- Listen to operating engines to detect and diagnose malfunctions, such as sticking or burned valves.
- Clean engines, sediment bulk and screens, and carburetors, adjusting carburetor float levels.
- Determine repair limits for engine hot section parts.
- Remove, inspect, repair, and install in-flight refueling stores and external fuel tanks.
- Prepare and paint aircraft surfaces.
- Spread plastic film over areas to be repaired to prevent damage to surrounding areas.
- Trim and shape replacement body sections to specified sizes and fits and secure sections in place, using adhesives, hand tools, and power tools.
- Cover surfaces with laminated plastic covering material.
- Cut timbers, lumber, or paneling to specified dimensions.
- Cut and install insulating or sound-absorbing material.
- Cut tile or linoleum to fit and spread adhesives on flooring for installation.
- Clean work areas, machines, or equipment, to maintain a clean and safe job site.
- Fasten timbers or lumber with glue, screws, pegs, or nails and install hardware.
- Perform tie spacing layout and measure, mark, drill or cut.
- Select tools, equipment, or materials from storage and transport items to work site.
- Drill holes in timbers or lumber.
- Position and hold timbers, lumber, or paneling in place for fastening or cutting.
- Align, straighten, plumb, or square forms for installation.
- Hold plumb bobs, sighting rods, or other equipment to aid in establishing reference points and lines.
- Erect scaffolding, shoring, or braces.
- Construct forms and assist in raising them to the required elevation.
- Install handrails under the direction of a carpenter.
- Glue and clamp edges or joints of assembled parts.
- Smooth or sand surfaces to remove ridges, tool marks, glue, or caulking.
- Secure stakes to grids for constructions of footings, nail scabs to footing forms, and vibrate and float concrete.
- Cover surfaces with laminated plastic covering material.
- Cut timbers, lumber, or paneling to specified dimensions.
- Cut and install insulating or sound-absorbing material.
- Cut tile or linoleum to fit and spread adhesives on flooring for installation.
- Cut new or duplicate keys, using key cutting machines.
- Disassemble mechanical or electrical locking devices, and repair or replace worn tumblers, springs, and other parts, using hand tools.
- Cut new or duplicate keys, using impressions or code key machines.
- Open safe locks by drilling.
- Install door hardware, such as locks and closers.
- Insert new or repaired tumblers into locks to change combinations.
- Set up and maintain master key systems.
- Keep records of company locks and keys.
- Move picklocks in cylinders to open door locks without keys.
- Repair and adjust safes, vault doors, and vault components, using hand tools, lathes, drill presses, and welding and acetylene cutting apparatus.
- Install safes, vault doors, and deposit boxes according to blueprints, using equipment such as power drills, taps, dies, truck cranes, and dollies.
- Install alarm and electronic access systems.
- Unlock cars and other vehicles.
- Remove interior and exterior finishes on safes and vaults, and spray on new finishes.
- Cut new or duplicate keys, using key cutting machines.
- Open and close doors, windows, and drawers to test their operation, trimming edges to fit, using jackplanes or drawknives.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Move and set up mobile homes or prefabricated buildings on owners' lots or at mobile home parks.
- Inspect, examine, and test the operation of parts or systems to evaluate operating condition and to determine if repairs are needed.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of plumbing fixtures.
- Remove damaged exterior panels, repair and replace structural frame members, and seal leaks, using hand tools.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, and diagrams.
- Confer with customers or read work orders to determine the nature and extent of damage to units.
- Install, repair, and replace units, fixtures, appliances, and other items and systems in mobile and modular homes, prefabricated buildings, or travel trailers, using hand tools or power tools.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Repair leaks in plumbing or gas lines, using caulking compounds and plastic or copper pipe.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, and hand tools.
- Connect electrical systems to outside power sources and activate switches to test the operation of appliances and light fixtures.
- Refinish wood surfaces on cabinets, doors, moldings, and floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Open and close doors, windows, and drawers to test their operation, trimming edges to fit, using jackplanes or drawknives.
- Measure, cut, and install frameworks and conduit to support and connect wiring, control panels, and junction boxes, using hand tools.
- Inspect and test electrical systems and equipment to locate and diagnose malfunctions, using visual inspections, testing devices, and computer software.
- Reassemble and test equipment after repairs.
- Adjust, repair, or replace defective wiring and relays in ignition, lighting, air-conditioning, and safety control systems, using electrician's tools.
- Splice wires with knives or cutting pliers, and solder connections to fixtures, outlets, and equipment.
- Locate and remove or repair circuit defects such as blown fuses or malfunctioning transistors.
- Maintain equipment service records.
- Refer to schematics and manufacturers' specifications that show connections and provide instructions on how to locate problems.
- Install fixtures, outlets, terminal boards, switches, and wall boxes, using hand tools.
- Install new fuses, electrical cables, or power sources as required.
- Cut openings and drill holes for fixtures, outlet boxes, and fuse holders, using electric drills and routers.
- Confer with customers to determine the nature of malfunctions.
- Install electrical equipment such as air-conditioning, heating, or ignition systems and components such as generator brushes and commutators, using hand tools.
- Repair or rebuild equipment such as starters, generators, distributors, or door controls, using electrician's tools.
- Estimate costs of repairs based on parts and labor requirements.
- Measure, cut, and install frameworks and conduit to support and connect wiring, control panels, and junction boxes, using hand tools.
- Apply protective materials to equipment, components, and parts to prevent defects and corrosion.
- Install or replace machinery, equipment, and new or replacement parts and instruments, using hand or power tools.
- Examine and test machinery, equipment, components, and parts for defects to ensure proper functioning.
- Tend and observe equipment and machinery to verify efficient and safe operation.
- Adjust, connect, or disconnect wiring, piping, tubing, and other parts, using hand or power tools.
- Clean or lubricate vehicles, machinery, equipment, instruments, tools, work areas, and other objects, using hand tools, power tools, and cleaning equipment.
- Diagnose electrical problems and install and rewire electrical components.
- Disassemble broken or defective equipment to facilitate repair and reassemble equipment when repairs are complete.
- Position vehicles, machinery, equipment, physical structures, and other objects for assembly or installation, using hand tools, power tools, and moving equipment.
- Transfer tools, parts, equipment, and supplies to and from work stations and other areas.
- Adjust, maintain, and repair tools, equipment, and machines, and assist more skilled workers with similar tasks.
- Order new parts to maintain inventory.
- Design, weld, and fabricate parts, using blueprints or other mechanical plans.
- Assemble and maintain physical structures, using hand or power tools.
- Prepare work stations for use by mechanics and repairers.
- Hold or supply tools, parts, equipment, and supplies for other workers.
- Apply protective materials to equipment, components, and parts to prevent defects and corrosion.
- Cut and weld metal to repair broken metal parts, fabricate new parts, or assemble new equipment.
- Repair or maintain the operating condition of industrial production or processing machinery or equipment.
- Repair or replace broken or malfunctioning components of machinery or equipment.
- Clean, lubricate, or adjust parts, equipment, or machinery.
- Disassemble machinery or equipment to remove parts and make repairs.
- Reassemble equipment after completion of inspections, testing, or repairs.
- Examine parts for defects, such as breakage or excessive wear.
- Record repairs and maintenance performed.
- Operate newly repaired machinery or equipment to verify the adequacy of repairs.
- Record parts or materials used and order or requisition new parts or materials, as necessary.
- Observe and test the operation of machinery or equipment to diagnose malfunctions, using voltmeters or other testing devices.
- Analyze test results, machine error messages, or information obtained from operators to diagnose equipment problems.
- Study blueprints or manufacturers' manuals to determine correct installation or operation of machinery.
- Enter codes and instructions to program computer-controlled machinery.
- Demonstrate equipment functions and features to machine operators.
- Assign schedules to work crews.
- Cut and weld metal to repair broken metal parts, fabricate new parts, or assemble new equipment.
- Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.
- Reline or repair ladles and pouring spouts with refractory clay, using trowels.
- Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.
- Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.
- Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.
- Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.
- Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.
- Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.
- Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.
- Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.
- Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.
- Dump and tamp clay in molds, using tamping tools.
- Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.
- Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.
- Install preformed metal scaffolding in interiors of cupolas, using hand tools.
- Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.
- Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.
- Open and close doors, windows, or drawers to test their operation, trimming edges to fit, as necessary.
- Explain proper operation of vehicle systems to customers.
- Locate and repair frayed wiring, broken connections, or incorrect wiring, using ohmmeters, soldering irons, tape, or hand tools.
- Repair plumbing or propane gas lines, using caulking compounds and plastic or copper pipe.
- Confer with customers, read work orders, or examine vehicles needing repair to determine the nature and extent of damage.
- Examine or test operation of parts or systems to ensure completeness of repairs.
- Connect electrical systems to outside power sources, and activate switches to test the operation of appliances or light fixtures.
- Connect water hoses to inlet pipes of plumbing systems, and test operation of toilets or sinks.
- Inspect recreational vehicles to diagnose problems and perform necessary adjustment, repair, or overhaul.
- Inspect, repair, or replace brake systems.
- Diagnose and repair furnace or air conditioning systems.
- Repair leaks with caulking compound or replace pipes, using pipe wrenches.
- List parts needed, estimate costs, and plan work procedures, using parts lists, technical manuals, or diagrams.
- Remove damaged exterior panels, and repair and replace structural frame members.
- Reset hardware, using chisels, mallets, and screwdrivers.
- Refinish wood surfaces on cabinets, doors, moldings, or floors, using power sanders, putty, spray equipment, brushes, paints, or varnishes.
- Seal open sides of modular units to prepare them for shipment, using polyethylene sheets, nails, and hammers.
- Open and close doors, windows, or drawers to test their operation, trimming edges to fit, as necessary.
- Drape and pin protective cloths around customers' shoulders.
- Clean and sterilize scissors, combs, clippers, and other instruments.
- Cut and trim hair according to clients' instructions or current hairstyles, using clippers, combs, hand-held blow driers, and scissors.
- Question patrons regarding desired services and haircut styles.
- Clean work stations and sweep floors.
- Apply lather and shave beards or neck and temple hair contours, using razors.
- Record services provided on cashiers' tickets or receive payment from customers.
- Shape and trim beards and moustaches, using scissors.
- Perform clerical and administrative duties such as keeping records, paying bills, and hiring and supervising personnel.
- Stay informed of the latest styles and hair care techniques.
- Suggest treatments to alleviate hair problems.
- Order supplies.
- Shampoo hair.
- Recommend and sell lotions, tonics, or other cosmetic supplies.
- Measure, fit, and groom hairpieces.
- Identify hair problems, using microscopes and testing devices, or by sending clients' hair samples out to independent laboratories for analysis.
- Provide skin care and nail treatments.
- Keep card files on clientele, recording notes of work done, products used and fees charged after each visit.
- Curl, color, or straighten hair, using special chemical solutions and equipment.
- Provide face, neck, and scalp massages.
- Drape and pin protective cloths around customers' shoulders.
- Apply coatings or operate systems to mitigate corrosion of geothermal plant equipment or structures.
- Monitor and adjust operations of geothermal power plant equipment or systems.
- Prepare and maintain logs, reports, or other documentation of work performed.
- Identify and correct malfunctions of geothermal plant equipment, electrical systems, instrumentation, or controls.
- Collect and record data associated with operating geothermal power plants or well fields.
- Determine whether emergency or auxiliary systems will be needed to keep properties heated or cooled in extreme weather conditions.
- Perform pre- and post-installation pressure, flow, and related tests of vertical and horizontal geothermal loop piping.
- Identify equipment options, such as compressors, and make appropriate selections.
- Adjust power production systems to meet load and distribution demands.
- Maintain electrical switchgear, process controls, transmitters, gauges, and control equipment in accordance with geothermal plant procedures.
- Calculate heat loss and heat gain factors for residential properties to determine heating and cooling required by installed geothermal systems.
- Maintain, calibrate, or repair plant instrumentation, control, and electronic devices in geothermal plants.
- Install and maintain geothermal plant electrical protection equipment.
- Design and lay out geothermal heat systems according to property characteristics, heating and cooling requirements, piping and equipment requirements, applicable regulations, or other factors.
- Install and maintain geothermal system instrumentation or controls.
- Prepare newly installed geothermal heat systems for operation by flushing, purging, or other actions.
- Weld piping, such as high density polyethylene (HDPE) piping, using techniques such as butt, socket, side-wall, and electro-fusion welding.
- Test water sources for factors, such as flow volume and contaminant presence.
- Install, maintain, or repair ground or water source-coupled heat pumps to heat and cool residential or commercial building air or water.
- Integrate hot water heater systems with geothermal heat exchange systems.
- Determine the type of geothermal loop system most suitable to a specific property and its heating and cooling needs.
- Dig trenches for system piping to appropriate depths and lay piping in trenches.
- Backfill piping trenches to protect pipes from damage.
- Operate equipment, such as excavators, backhoes, rock hammers, trench compactors, pavement saws, grout mixers or pumps, geothermal loop reels, and coil tubing units (CTU).
- Apply coatings or operate systems to mitigate corrosion of geothermal plant equipment or structures.
- Cut door stops or angle irons to fit openings.
- Wind large springs with upward motion of arm.
- Adjust doors to open or close with the correct amount of effort, or make simple adjustments to electric openers.
- Carry springs to tops of doors, using ladders or scaffolding, and attach springs to tracks to install spring systems.
- Repair or replace worn or broken door parts, using hand tools.
- Complete required paperwork, such as work orders, according to services performed or required.
- Fasten angle iron back-hangers to ceilings and tracks, using fasteners or welding equipment.
- Collect payment upon job completion.
- Install door frames, rails, steel rolling curtains, electronic-eye mechanisms, or electric door openers and closers, using power tools, hand tools, and electronic test equipment.
- Inspect job sites, assessing headroom, side room, or other conditions to determine appropriateness of door for a given location.
- Assemble and fasten tracks to structures or bucks, using impact wrenches or welding equipment.
- Set doors into place or stack hardware sections into openings after rail or track installation.
- Operate lifts, winches, or chain falls to move heavy curtain doors.
- Remove or disassemble defective automatic mechanical door closers, using hand tools.
- Fabricate replacements for worn or broken parts, using welders, lathes, drill presses, or shaping or milling machines.
- Prepare doors for hardware installation, such as drilling holes to install locks.
- Run low voltage wiring on ceiling surfaces, using insulated staples.
- Study blueprints and schematic diagrams to determine appropriate methods of installing or repairing automated door openers.
- Install dock seals, bumpers, or shelters.
- Order replacement springs, sections, or slats.
- Lubricate door closer oil chambers, and pack spindles with leather washers.
- Set in and secure floor treadles for door-activating mechanisms, and connect power packs and electrical panelboards to treadles.
- Cover treadles with carpeting or other floor covering materials, and test systems by operating treadles.
- Bore or cut holes in flooring as required for installation, using hand or power tools.
- Clean door closer parts, using caustic soda, rotary brushes, or grinding wheels.
- Cut door stops or angle irons to fit openings.
- Measure, cut, thread, or bend pipe or tubing, using pipe fitter's tools.
- Test electrical circuits or components for continuity, using electrical test equipment.
- Comply with all applicable standards, policies, or procedures, such as safety procedures or the maintenance of a clean work area.
- Study blueprints, design specifications, or manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.
- Discuss heating or cooling system malfunctions with users to isolate problems or to verify that repairs corrected malfunctions.
- Connect heating or air conditioning equipment to fuel, water, or refrigerant source to form complete circuit.
- Adjust system controls to settings recommended by manufacturer to balance system.
- Recommend, develop, or perform preventive or general maintenance procedures, such as cleaning, power-washing, or vacuuming equipment, oiling parts, or changing filters.
- Inspect and test systems to verify system compliance with plans and specifications or to detect and locate malfunctions.
- Repair or replace defective equipment, components, or wiring.
- Install or repair self-contained ground source heat pumps or hybrid ground or air source heat pumps to minimize carbon-based energy consumption and reduce carbon emissions.
- Install, connect, or adjust thermostats, humidistats, or timers.
- Install auxiliary components to heating or cooling equipment, such as expansion or discharge valves, air ducts, pipes, blowers, dampers, flues, or stokers.
- Braze or solder parts to repair defective joints and leaks.
- Lay out and connect electrical wiring between controls and equipment, according to wiring diagrams, using electrician's hand tools.
- Perform mechanical overhauls and refrigerant reclaiming.
- Install expansion and control valves, using acetylene torches and wrenches.
- Mount compressor, condenser, and other components in specified locations on frames, using hand tools and acetylene welding equipment.
- Install dehumidifiers or related equipment for spaces that require cool, dry air to operate efficiently, such as computer rooms.
- Record and report time, materials, faults, deficiencies, or other unusual occurrences on work orders.
- Keep records of repairs and replacements made and causes of malfunctions.
- Cut or drill holes in floors, walls, or roof to install equipment, using power saws or drills.
- Estimate, order, pick up, deliver, and install materials and supplies needed to maintain equipment in good working condition.
- Schedule work with customers and initiate work orders, house requisitions, and orders from stock.
- Supervise and instruct assistants.
- Lay out reference points for installation of structural and functional components, using measuring instruments.
- Lift and align components into position, using hoist or block and tackle.
- Install or repair air purification systems, such as specialized filters or ultraviolet (UV) light purification systems.
- Repair or service heating, ventilating, and air conditioning (HVAC) systems to improve efficiency, such as by changing filters, cleaning ducts, and refilling non-toxic refrigerants.
- Test pipes, lines, components, and connections for leaks.
- Measure, cut, thread, or bend pipe or tubing, using pipe fitter's tools.
- Measure, cut, and thread pipe, and connect it to feeder lines and equipment or appliances, using rules and hand tools.
- Bill customers for repair work, and collect payment.
- Observe and examine appliances during operation to detect specific malfunctions such as loose parts or leaking fluid.
- Talk to customers or refer to work orders to establish the nature of appliance malfunctions.
- Refer to schematic drawings, product manuals, and troubleshooting guides to diagnose and repair problems.
- Trace electrical circuits, following diagrams, and conduct tests with circuit testers and other equipment to locate shorts and grounds.
- Replace worn and defective parts such as switches, bearings, transmissions, belts, gears, circuit boards, or defective wiring.
- Provide repair cost estimates, and recommend whether appliance repair or replacement is a better choice.
- Disassemble appliances so that problems can be diagnosed and repairs can be made.
- Respond to emergency calls for problems such as gas leaks.
- Service and repair domestic electrical or gas appliances, such as clothes washers, refrigerators, stoves, and dryers.
- Reassemble units after repairs are made, making adjustments and cleaning and lubricating parts as needed.
- Record maintenance and repair work performed on appliances.
- Test and examine gas pipelines and equipment to locate leaks and faulty connections, and to determine the pressure and flow of gas.
- Light and adjust pilot lights on gas stoves, and examine valves and burners for gas leakage and specified flame.
- Instruct customers regarding operation and care of appliances, and provide information such as emergency service numbers.
- Contact supervisors or offices to receive repair assignments.
- Maintain stocks of parts used in on-site installation, maintenance, and repair of appliances.
- Level refrigerators, adjust doors, and connect water lines to water pipes for ice makers and water dispensers, using hand tools.
- Observe and test operation of appliances following installation, and make any initial installation adjustments that are necessary.
- Set appliance thermostats, and check to ensure that they are functioning properly.
- Install appliances such as refrigerators, washing machines, and stoves.
- Level washing machines and connect hoses to water pipes, using hand tools.
- Clean and reinstall parts.
- Clean, lubricate, and touch up minor defects on newly installed or repaired appliances.
- Conserve, recover, and recycle refrigerants used in cooling systems.
- Install gas pipes and water lines to connect appliances to existing gas lines or plumbing.
- Take measurements to determine if appliances will fit in installation locations, performing minor carpentry work when necessary to ensure proper installation.
- Assemble new or reconditioned appliances.
- Disassemble and reinstall existing kitchen cabinets, or assemble and install prefabricated kitchen cabinets and trim in conjunction with appliance installation.
- Hang steel supports from beams or joists to hold hoses, vents, and gas pipes in place.
- Measure, cut, and thread pipe, and connect it to feeder lines and equipment or appliances, using rules and hand tools.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Record maintenance information, including test results, material usage, and repairs made.
- Disassemble and repair mechanical control devices or valves, such as regulators, thermostats, or hydrants, using power tools, hand tools, and cutting torches.
- Lubricate wearing surfaces of mechanical parts, using oils or other lubricants.
- Calibrate instrumentation, such as meters, gauges, and regulators, for pressure, temperature, flow, and level.
- Install, inspect and test electric meters, relays, and power sources to detect causes of malfunctions and inaccuracies, using hand tools and testing equipment.
- Test valves and regulators for leaks and accurate temperature and pressure settings, using precision testing equipment.
- Record meter readings and installation data on meter cards, work orders, or field service orders, or enter data into hand-held computers.
- Turn meters on or off to establish or close service.
- Shut off service and notify repair crews when major repairs are required, such as the replacement of underground pipes or wiring.
- Install regulators and related equipment such as gas meters, odorization units, and gas pressure telemetering equipment.
- Turn valves to allow measured amounts of air or gas to pass through meters at specified flow rates.
- Report hazardous field situations and damaged or missing meters.
- Vary air pressure flowing into regulators and turn handles to assess functioning of valves and pistons.
- Examine valves or mechanical control device parts for defects, dents, or loose attachments, and mark malfunctioning areas of defective units.
- Mount and install meters and other electric equipment such as time clocks, transformers, and circuit breakers, using electricians' hand tools.
- Connect regulators to test stands, and turn screw adjustments until gauges indicate that inlet and outlet pressures meet specifications.
- Investigate instances of illegal tapping into service lines.
- Trace and tag meters or house lines.
- Repair electric meters and components, such as transformers and relays, and replace metering devices, dial glasses, and faulty or incorrect wiring, using hand tools.
- Replace defective parts, such as bellows, range springs, and toggle switches, and reassemble units according to blueprints, using cam presses and hand tools.
- Recondition displacement type gas meters and governors, fabricating, machining, or modifying parts needed for repairs.
- Measure tolerances of assembled and salvageable parts for conformance to standards or specifications, using gauges, micrometers, and calipers.
- Clean internal compartments and moving parts, using rags and cleaning compounds.
- Dismantle meters, and replace or adjust defective parts such as cases, shafts, gears, disks, and recording mechanisms, using soldering irons and hand tools.
- Disconnect or remove defective or unauthorized meters, using hand tools.
- Reassemble repaired equipment, and solder top, front, and back case panels in place, using soldering guns, power tools, and hand tools.
- Attach air hoses to meter inlets, plug outlets, and observe gauges for pressure losses to test internal seams for leaks.
- Make adjustments to meter components, such as setscrews or timing mechanisms, so that they conform to specifications.
- Recommend and write up specifications for changes in hardware, such as house wiring.
- Clamp regulator units into vises on stages above water tanks, and attach compressed air hoses to intake ports.
- Repair leaks in valve seats or bellows of automotive heater thermostats, using soft solder, flux, and acetylene torches.
- Collect money due on delinquent accounts.
- Splice and connect cables from meters or current transformers to pull boxes or switchboards, using hand tools.
- Attach pressurized meters to fixtures which submerge them in water, and observe meters for leaks.
- Advise customers on proper installation of valves or regulators and related equipment.
- Calibrate thermostats for specified temperature or pressure settings.
- Clean plant growth, scale, paint, soil, or rust from meter housings, using wire brushes, scrapers, buffers, sandblasters, or cleaning compounds.
- Connect hoses from provers to meter inlets and outlets, and raise prover bells until prover gauges register zero.
- Cut seats to receive new orifices, tap inspection ports, and perform other repairs to salvage usable materials, using hand tools and machine tools.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
- Inspect and test equipment to locate damage or worn parts and diagnose malfunctions, or read work orders or schematic drawings to determine required repairs.
- Reassemble repaired electric motors to specified requirements and ratings, using hand tools and electrical meters.
- Measure velocity, horsepower, revolutions per minute (rpm), amperage, circuitry, and voltage of units or parts to diagnose problems, using ammeters, voltmeters, wattmeters, and other testing devices.
- Repair and rebuild defective mechanical parts in electric motors, generators, and related equipment, using hand tools and power tools.
- Lift units or parts such as motors or generators, using cranes or chain hoists, or signal crane operators to lift heavy parts or subassemblies.
- Record repairs required, parts used, and labor time.
- Disassemble defective equipment so that repairs can be made, using hand tools.
- Adjust working parts, such as fan belts, contacts, and springs, using hand tools and gauges.
- Lubricate moving parts.
- Read service guides to find information needed to perform repairs.
- Inspect electrical connections, wiring, relays, charging resistance boxes, and storage batteries, following wiring diagrams.
- Scrape and clean units or parts, using cleaning solvents and equipment such as buffing wheels.
- Weld, braze, or solder electrical connections.
- Verify and adjust alignments and dimensions of parts, using gauges and tracing lathes.
- Steam-clean polishing and buffing wheels to remove abrasives and bonding materials, and spray, brush, or recoat surfaces as necessary.
- Set machinery for proper performance, using computers.
- Test equipment for overheating, using speed gauges and thermometers.
- Reface, ream, and polish commutators and machine parts to specified tolerances, using machine tools.
- Maintain stocks of parts.
- Assemble electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools.
- Solder, wrap, and coat wires to ensure proper insulation.
- Rewire electrical systems, and repair or replace electrical accessories.
- Clean cells, cell assemblies, glassware, leads, electrical connections, and battery poles, using scrapers, steam, water, emery cloths, power grinders, or acid.
- Rewind coils on cores in slots, or make replacement coils, using coil-winding machines.
- Test conditions, fluid levels, and specific gravities of electrolyte cells, using voltmeters, hydrometers, and thermometers.
- Add water or acid to battery cell solutions to obtain specified concentrations.
- Pour compounds into transformer-case terminal openings to seal out moisture.
- Remove and replace defective parts such as coil leads, carbon brushes, and wires, using soldering equipment.
- Hammer out dents and twists in tools and equipment.
- Drain and filter transformer oil and refill transformers with oil until coils are submerged.
- Seal joints with putty, mortar, and asbestos, using putty extruders and knives.
- Repair and operate battery-charging equipment.
- Sharpen tools such as saws, picks, shovels, screwdrivers, and scoops, either manually or by using bench grinders and emery wheels.
- Inspect batteries for structural defects such as dented cans, damaged carbon rods and terminals, and defective seals.
- Test battery charges, and replace or recharge batteries as necessary.
- Bolt porcelain insulators to wood parts to assemble hot stools.
- Position and level battery cells, anodes, or cathodes, using hoists or leveling jacks, or signal other workers to perform positioning and leveling.
- Clean, rinse, and dry transformer cases, using boiling water, scrapers, solvents, hoses, and cloths.
- Cut and form insulation, and insert insulation into armature, rotor, or stator slots.
